AXIS Q1614 Network Camera User Manual
About this Document This manual is intended for administrators and users of the AXIS Q1614/Q1614–E Fixed Dome Network Camera, and is applicable to firmware 5.60 and later. It includes instructions for using and managing the product on your network. Previous experience of networking will be of use when using this product. Some knowledge of UNIX or Linux-based systems may also be beneficial, for developing shell scripts and applications.
Safety This product complies with IEC/EN/UL 60950-1, Safety of Information Technology Equipment. If its connecting cables are routed outdoors, the product shall be grounded either through a shielded network cable (STP) or other appropriate method. The power supply used with this product shall fulfill the requirements for Safety Extra Low Voltage (SELV) and Limited Power Source (LPS) according to IEC/EN/UL 60950-1. Battery The Axis product uses a 3.
AXIS Q1614 Network Camera Table of Contents Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Connectors and Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Status LED Behavior for Focus Assistant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Buzzer Signal for Focus Assistant . . . . . .
AXIS Q1614 Network Camera Table of Contents Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I/O Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AXIS Q1614 Network Camera Hardware Overview Hardware Overview 1 2 3 10 4 5 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 6 7 8 9 11 12 13 14 15 Status LED indicator Zoom puller Focus puller I/O connector Iris connector Power connector Power LED indicator Network LED indicator RS485/RS422 connector Network connector (PoE) Control button (1) Function button (2) microSD Card slot Audio in Audio out Connectors and Buttons For technical specifications, see page 64.
AXIS Q1614 Network Camera Hardware Overview Network Connector RJ45 Ethernet connector with Power over Ethernet (PoE). NOTICE TICE NO The product shall be connected using a shielded network cable (STP). All cables connecting the product to the network shall be intended for their specific use. Make sure that the network devices are installed in accordance with the manufacturer’s instructions. For information about regulatory requirements, see Electromagnetic Compatibility (EMC) on page 2 .
AXIS Q1614 Network Camera Hardware Overview • Connecting to AXIS Internet Dynamic DNS Service. See page 51. To connect, press and hold the button for about 3 seconds. Function Button The function button has multiple functions: • Levelling assistant – This function helps to ensure the camera is level. Press the button for about 3 seconds to start the levelling assistant and press again to stop the leveling assistant.
AXIS Q1614 Network Camera Hardware Overview Buzzer Signal for Focus Assistant Buzzer Lens Fast interval Optimally adjusted Medium interval Less optimally adjusted Slow interval Poorly adjusted Status LED Behavior and Buzzer Signal for Levelling Assistant For information on the Function button used for levelling the camera, see Connectors and Buttons.
AXIS Q1614 Network Camera Hardware Overview Note • If you select a DC iris configuration file for a P-iris lens, an error message will appear below the iris configuration type in the Camera Settings page. For custom DC Iris lenses, select Generic DC Iris option. • There is no need to restart the product after changing the lens. However, the product must be restarted if you are interchanging between a P-iris, DC-Iris or fixed/manual iris lens.
AXIS Q1614 Network Camera Access the Product Access the Product To install the Axis product, refer to the Installation Guide supplied with the product. The product can be used with most operating systems and browsers. The recommended browsers are Internet Explorer with Windows, Safari with Macintosh and Firefox with other operating systems. See Technical Specifications on page 64. To view streaming video in Internet Explorer, allow installation of AXIS Media Control (AMC) when prompted.
AXIS Q1614 Network Camera Access the Product To prevent network eavesdropping, the root password can be set via an encrypted HTTPS connection, which requires an HTTPS certificate. HTTPS (Hypertext Transfer Protocol over SSL) is a protocol used to encrypt traffic between web browsers and servers. The HTTPS certificate ensures encrypted exchange of information. See HTTPS on page 47. The default administrator user name root is permanent and cannot be deleted.
AXIS Q1614 Network Camera Access the Product Controls on the Live View Page Click the View size buttons to show the image in full size (right button) or to scale down the image to fit the browser window (left button). Click WDR on to enable WDR in intense backlight conditions. Read more about wide dynamic range on page 23. Click Lightfinder Mode to enable this mode. Read more about Lightfinder on page 23. Click WDR on to enable WDR in intense backlight conditions.
AXIS Q1614 Network Camera Access the Product 1. Go to Setup > Live View Config. 2. Under Action Buttons, select Show manual trigger button. AXIS Media Control viewer toolbar The AXIS Media Control viewer toolbar is available in Internet Explorer only. See AXIS Media Control (AMC) on page 16 for more information. The toolbar displays the following buttons: The Play button connects to the Axis product and starts playing a media stream. The Stop button stops the media stream.
AXIS Q1614 Network Camera Access the Product With the PTZ Control Queue enabled the time each user is in control of the PTZ settings is limited. Click the buttons to request or release control of the PTZ controls. The PTZ Control Queue is set up under PTZ > Control Queue. Click the Emulate joystick mode button and click in the image to move the camera view in the direction of the mouse pointer. Click the Center mode button and click in the image to center the camera view on that position.
AXIS Q1614 Network Camera Media Streams Media Streams The Axis product provides several audio and video stream formats. Your requirements and the properties of your network will determine the type you use. The Live View page in the product provides access to H.264 and Motion JPEG video streams, audio streams and to the list of available stream profiles. Other applications and clients can access video and audio streams directly, without going via the Live View page. How to Stream H.264 H.
AXIS Q1614 Network Camera Media Streams The AMC Control Panel can be used to configure various video and audio settings. Please see the AXIS Media Control User’s Manual for more information. The AMC Control Panel is automatically installed on first use, after which it can be configured. Open the AMC Control Panel from: • Windows Control Panel (from the Start screen or Start menu) • Alternatively, right-click the video image in Internet Explorer and click Settings.
AXIS Q1614 Network Camera Media Streams Note • = IP addess • The Axis product supports QuickTime 6.5.1 and later. • QuickTime may add latency to the video stream. • It may be possible to use other players to view the H.264 stream using the paths above, although Axis does not guarantee this.
AXIS Q1614 Network Camera Set Up the Product Set Up the Product The Axis product can be configured by users with administrator or operator rights. To open the product’s Setup pages, click Setup in the top right-hand corner of the Live View page. • Administrators have unrestricted access to all settings. • Operators have access to all settings except System Options See also the online help . Basic Setup Basic Setup provides shortcuts to the settings that should be made before using the Axis product: 1.
AXIS Q1614 Network Camera Video and Audio Video and Audio The video and audio settings can be used to optimize video and audio quality. You can configure the following: • Video stream settings. See page 20. • Stream profiles. See page 21. • Camera settings. See page 22. • View area. See page 25. • Overlay image. See page 25. • Privacy mask. See page 27. • Focus. See page 27. • Audio settings. See page 28. • Audio clips. See page 29.
AXIS Q1614 Network Camera Video and Audio • Mirror image. If required, the image can be mirrored. • Rotate image. If required, the image can be rotated. • Maximum frame rate. To avoid bandwidth problems, the frame rate allowed to each viewer can be Limited to a fixed amount. Alternatively, the frame rate can be set as Unlimited, which means the Axis product always delivers the highest frame rate possible under the current conditions. • Overlay settings. See Overlay on page 25.
AXIS Q1614 Network Camera Video and Audio • When setting up continuous recording. See Continuous Recording on page 45. • In the Live View page – select the stream profile from the Stream profile drop-down list. For quick setup, use one of the predefined stream profiles. Each predefined profile has a descriptive name, indicating its purpose. If required, the predefined stream profiles can be modified and new customized stream profiles can be created.
AXIS Q1614 Network Camera Video and Audio Image Appearance Increasing the Color level increases the color saturation. The value 100 gives maximum color saturation. The value 0 gives a black and white image. The image Brightness can be adjusted in the range 0–100, where a higher value produces a brighter image. Increasing the Sharpness can increase bandwidth usage. A sharper image might increase image noise especially in low light conditions.
AXIS Q1614 Network Camera Video and Audio Shutter speed is related to the amount of time the shutter is opened and is measured in seconds (s). A slow shutter speed allows more light to reach the sensor and can help produce a brighter image in low light situations. On the other hand, a slow shutter speed can cause moving objects to appear blurry. Set Shutter to • Auto to set the shutter speed automatically. If required, use Max shutter to limit the shutter speed to prevent the frame rate from being reduced.
AXIS Q1614 Network Camera Video and Audio View Area Note This feature is available only if digital PTZ was selected when configuring the product for the first time or after resetting to factory default. A view area is a cropped part of the full view. The view area is treated as a video source in Live View and has its own video stream and PTZ settings. When setting up a view area it is recommended that the video stream resolution is the same size as or smaller than the view area size.
AXIS Q1614 Network Camera Video and Audio Overlay Image An overlay image is a static image superimposed over the video stream. The image, for example a company logo, is used to provide extra information or to mask a part of the image. For more information about privacy masks, see Privacy Mask on page 27. To use an overlay image, the image must first be uploaded to the Axis product. The uploaded image should be a Windows 24-bit BMP image with maximum 250 colors.
AXIS Q1614 Network Camera Video and Audio Create the action rule: 1. Go to Events > Action Rules 2. Click Add to create a new rule. 3. Select a Trigger and, optionally, a Schedule and Additional conditions. See the online help for details. 4. From the Actions list, select Overlay Text 5. Enter the text to display in the Text field. This is the text that #D will be replaced by. 6. Specify the Duration. The text can be displayed while the rule is active or for a fixed number of seconds.
AXIS Q1614 Network Camera Video and Audio Audio Settings The audio functionality for each video stream is enabled under Video & Audio > Video Stream > Audio. Audio Modes The Axis product supports the following audio modes: Full duplex - Simultaneous two-way audio allowing the Axis product to transmit and receive audio at the same time. There is no echo cancellation; if feedback loops appear, try moving the microphone or the speaker.
AXIS Q1614 Network Camera Video and Audio Use the Encoding option to select digital audio encoding format. • AAC requires a license for both encoding and decoding. AAC is the least complicated and most widely used codec. If achieving the best possible audio quality is a priority, AAC is the recommended codec to use. An AAC license is included in the Axis product.
AXIS Q1614 Network Camera Configure the Live View Page Configure the Live View Page You can customize the Live View page and alter it to suit your requirements. It is possible to define the following features of the Live View page. • Stream Profile. See page 21. • Default Viewer for Browser. See page 30. • Viewer Settings. See page 30. • Action Buttons. These are the buttons described in Controls on the Live View Page on page 13. • User Defined Links. See page 31. • Output Buttons. See page 31.
AXIS Q1614 Network Camera Configure the Live View Page • Select Use PTZ joystick mode as default to enable joystick mode. The mode can be changed temporarily from the PTZ control panel. • Select Enable recording button to enable recording from the Live View page. This button is available when using the AMC viewer. The recordings are saved to the location specified in the AMC Control Panel. See AXIS Media Control (AMC) on page 16.
AXIS Q1614 Network Camera PTZ (Pan Tilt Zoom) PTZ (Pan Tilt Zoom) The PTZ menu is available if digital PTZ (pan, tilt and zoom) is enabled in the selected view area or if a PTZ driver has been uploaded. For more information on view areas, see View Area on page 25. For more information on how to upload a driver, see Install PTZ Driver on page 33.
AXIS Q1614 Network Camera PTZ (Pan Tilt Zoom) 7. Click Save. To modify or remove guard tours, go to PTZ > Guard Tour, select the guard tour in the Guard Tour List and click Modify/Remove. For more information see the online help . Advanced Device Settings The Device Settings window displays driver specific settings. The appearance of this window can vary depending on the driver installed.
AXIS Q1614 Network Camera PTZ (Pan Tilt Zoom) A user who belongs to a group (see Users on page 47) with a higher PTZ priority can go before other users in the queue and take control of the product. The order of priority is as follows: 1. Administrator — An administrator takes over PTZ control regardless of who is first in queue. The administrator will be removed from the queue 60 seconds after the last PTZ control command. 2.
AXIS Q1614 Network Camera Detectors Detectors Camera Tampering Camera Tampering can generate an alarm whenever the camera is repositioned, or when the lens is covered, sprayed or severely defocused. To send an alarm, for example an email, an action rule must be set up. To configure tampering: 1. Go to Detectors > Camera Tampering. 2. Set the Minimum duration, that is, the time that must elapse before an alarm is generated. Increase time to prevent false alarms for known conditions that affect the image. 3.
AXIS Q1614 Network Camera Detectors To control the number of motion detection alarms, the parameters Object Size, History and Sensitivity can be adjusted. See Motion Detection Parameters on page 36. Once motion detection windows are configured, the Axis product can be configured to perform actions when motion is detected. Possible actions include uploading images and start recording. For more information, see Set Up Action Rules on page 40.
AXIS Q1614 Network Camera Detectors High level (100%) Only very large objects trigger motion detection. An object that appears in the window triggers motion detection for a long time before it is considered as non-moving. Ordinary colored objects on ordinary backgrounds trigger motion detection. A large difference in luminance is required to trigger motion detection. Medium level (50%) Low level (0%) Even very small objects trigger motion detection.
AXIS Q1614 Network Camera Applications Applications Third party applications can be uploaded to and installed on the Axis product. Applications add functionality to the product, for example video analytics and intelligent video capabilities such as recognition, tracking, detection and counting. For information about available applications, downloads, trials and licenses, go to www.axis.
AXIS Q1614 Network Camera Applications If the Axis product is reset to factory default, installed applications and their settings are removed. For information about factory default, see Reset to Factory Default Settings.
AXIS Q1614 Network Camera Events Events The Event pages allow you to configure the Axis product to perform actions when different events occur. For example, the product can start a recording or send an email notification when motion is detected. The set of conditions that defines how and when the action is triggered is called an action rule.
AXIS Q1614 Network Camera Events • • • • • • - Day/Night Mode – Trigger the rule when the product switches between day mode (IR cut filter on) and night mode (IR cut filter off). This can for example be used to control an external infrared (IR) light connected to an output port. - Live Stream Accessed – Trigger the rule when any stream is accessed and during edge storage playback. This can for example be used to send notifications. - Motion Detection – Trigger the rule when motion is detected.
AXIS Q1614 Network Camera Events Actions Available actions include: • Day/Night Vision Mode – Set day mode (IR cut filter on) or night mode (IR cut filter off). • Output Port – Activate an I/O port to control an external device. • Overlay Text – Display an overlay text. See Use Overlay Text in an Action Rule on page 26. • Play Audio Clip – See Audio Clips on page 29. • PTZ Control - Preset Position – Go to a preset position. - Guard Tour – Start a guard tour. See Guard Tour on page 32.
AXIS Q1614 Network Camera Events To set up an email recipient using one of the listed providers: 1. Go to Events > Recipients and click Add. 2. Enter a Name and select Email from the Type list. 3. Enter the email addresses to send emails to in the To field. Use commas to separate multiple addresses. 4. Select the email provider from the Provider list. 5. Enter the user ID and password for the email account. 6. Click Test to send a test email.
AXIS Q1614 Network Camera Recordings Recordings The Axis product can be configured to record video continuously or according to an action rule: • To start a continuous recording, see page 45. • To set up action rules, see page 40. • To access recordings, see Find Recordings on page 44. • To play recordings, see Play Recording on page 44. • To export a recording as a video clip, see Export Video Clip on page 45. • To configure camera controlled storage, see Storage on page 55.
AXIS Q1614 Network Camera Recordings To play a recording, follow these steps: 1. Go to Recordings > List. 2. To reduce the number of recordings displayed, select the desired options under Filter and click the Filter button to apply the filters. See also Find Recordings on page 44. 3. Select the recording and click Play. The recording will be played in a new browser window. Export Video Clip Recordings on the SD card or network share can be exported as video clips.
AXIS Q1614 Network Camera Languages Languages Multiple languages can be installed in the Axis product. All web pages including the online help will be displayed in the selected language. To switch languages, go to Setup > Languages and first upload the new language file. Browse and locate the file and click the Upload Language button. Select the new language from the list and click Save.
AXIS Q1614 Network Camera System Options System Options Security Users User access control is enabled by default and can be configured under System Options > Security > Users. An administrator can set up other users by giving them user names and passwords. It is also possible to allow anonymous viewer login, which means that anybody may access the Live View page.
AXIS Q1614 Network Camera System Options 2. Select an HTTPS certificate from the list of installed certificates. 3. Optionally, click Ciphers and select the encryption algorithms to use for SSL. 4. Set the HTTPS Connection Policy for the different user groups. 5. Click Save to enable the settings. To access the Axis product via the desired protocol, enter https:// or http:// in the address field in a browser. The HTTPS port can be changed on the System Options > Network > TCP/IP > Advanced page. IEEE 802.
AXIS Q1614 Network Camera System Options To install a self-signed certificate: 1. Go to Setup > System Options > Security > Certificates. 2. Click Create self-signed certificate and provide the requested information. To create and install a CA-signed certificate: 1. Create a self-signed certificate as described above. 2. Go to Setup > System Options > Security > Certificates. 3. Click Create certificate signing request and provide the requested information. 4.
AXIS Q1614 Network Camera System Options Network Basic TCP/IP Settings The Axis product supports IP version 4 and IP version 6. Both versions can be enabled simultaneously, and at least one version must always be enabled. IPv4 Address Configuration By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.
AXIS Q1614 Network Camera System Options ping -l 408 -t Windows example (this may require that you run the command prompt as an administrator) arp -s 192.168.0.125 00-40-8c-18-10-00 ping -l 408 -t 192.168.0.125 4. Check that the network cable is connected and then restart the product by disconnecting and reconnecting power. 5. Close the command prompt when the product responds with Reply from 192.168.0.125:... or similar. 6.
AXIS Q1614 Network Camera System Options Domain name - Enter the domain(s) to search for the host name used by the Axis product. Multiple domains can be separated by semicolons. The host name is always the first part of a fully qualified domain name, for example, myserver is the host name in the fully qualified domain name myserver.mycompany.com where mycompany.com is the domain name. Primary/Secondary DNS server - Enter the IP addresses of the primary and secondary DNS servers.
AXIS Q1614 Network Camera System Options Note • For NAT traversal to work, this must be supported by the router. The router must also support UPnPTM. • The router has many different names: “NAT router”, “Network router”, “Internet Gateway”, ”Broadband router”, “Broadband sharing device” or “Home firewall” but the essential purpose of the device is the same. Enable/Disable - When enabled, the Axis product attempts to configure port mapping in a NAT router on your network, using UPnPTM.
AXIS Q1614 Network Camera System Options SNMP The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups. AXIS Video MIB (Management Information Base) for video hardware can be used to monitor Axis-specific, hardware-related issues that may need administrative attention. For more information about AXIS Video MIB and to download MIB files, go to www.axis.
AXIS Q1614 Network Camera System Options Bonjour The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol. Bonjour can be disabled under System Options > Network > Bonjour. Storage SD Card NOTICE TICE NO To prevent corruption of recordings, the SD card should always be unmounted before it is ejected. Note For SD card recommendations see www.axis.
AXIS Q1614 Network Camera System Options The Axis product can be configured to automatically format SD cards that are inserted into the product. If autoformat is enabled and an SD card is inserted, the product will check if the SD card has the ext4 file system. If the card has a different file system, the card will automatically be formatted to ext4. Important If autoformat is enabled, only use new or empty SD cards. Any data stored on the card will be lost when the card is inserted into the Axis product.
AXIS Q1614 Network Camera System Options I/O Ports The Axis product provides two configurable input and output ports for connection of external devices. For information about how to connect external devices, see Connectors on page 67. The I/O ports are configured under System Options > Ports & Devices > I/O Ports. Select the port direction (Input or Output). The ports can be given descriptive names and their Normal states can be configured as Open circuit or Grounded circuit.
AXIS Q1614 Network Camera System Options • the focus position • uploaded applications are kept but must be restarted Click Default to reset all settings, including the IP address, to the factory default values. This button should be used with caution. The Axis product can also be reset to factory default using the control button, see Reset to Factory Default Settings on page 59.
AXIS Q1614 Network Camera System Options Axis strongly recommends that you do not use this function unless you understand the consequences. Axis Support does not provide assistance for problems with customized scripts. To open the Script Editor, go to System Options > Advanced > Scripting. If a script causes problems, reset the product to its factory default settings, see page 59. For more information, see www.axis.
AXIS Q1614 Network Camera Troubleshooting Troubleshooting Check the Firmware Firmware is software that determines the functionality of network devices. One of your first actions when troubleshooting a problem should be to check the current firmware version. The latest version may contain a correction that fixes your particular problem. The current firmware version in the Axis product is displayed in the page Setup > Basic Setup and in Setup > About.
AXIS Q1614 Network Camera Troubleshooting 5. Reinstall the product, referring to the Installation Guide. If the emergency recovery procedure does not get the product up and running again, contact Axis support at www.axis.com/techsup/ Symptoms, Possible Causes and Remedial Actions Problems setting the IP address When using ARP/Ping Try the installation again. The IP address must be set within two minutes after power has been applied to the product. Ensure the Ping length is set to 408.
AXIS Q1614 Network Camera Troubleshooting Problems with streaming H.264 Problems with AXIS Media Control (Internet Explorer only) To enable the updating of video images in Internet Explorer, set the browser to allow ActiveX controls. Also, make sure that AXIS Media Control is installed on your computer. No H.264 displayed in the client Check that the relevant H.264 connection methods and correct interface are enabled in the AMC Control Panel (streaming tab). See AXIS Media Control (AMC) on page 16.
AXIS Q1614 Network Camera Troubleshooting No audio Incorrect setup Check the sound card in the computer. Ensure that mute is not selected and that the volume settings are correct. Check that Enable audio support is selected under Setup > System Options > Security > Audio Support. Check that the correct Audio Input source is selected under Setup > Video & Audio > Audio Settings. Poor audio quality Stuttering Reduce the number of listeners and viewers. Decrease image resolution and compression.
AXIS Q1614 Network Camera Technical Specifications Technical Specifications Function/group Item Specifications Camera Models AXIS Q1614: 1 MP/HDTV 720p, indoor Image sensor Progressive scan RGB CMOS 1/3” Lens P-iris, IR corrected, varifocal, CS-mount, support for DC-Iris lens, megapixel resolution 2.8 - 8 mm, F1.
AXIS Q1614 Network Camera Technical Specifications Function/group Item Specifications Audio Audio streaming Two-way, full duplex Audio compression AAC LC 8/16/32 kHz, 8-128 kbit/s G.711 PCM 8 kHz 64 kbit/s G.726 ADPCM 8 kHz 32 kbit/s or 24 kbit/s Configurable bit rate Audio input Audio Input: 3.5mm jack for: mic/line in. Max 80 mVpp for microphone/ Max 6.
AXIS Q1614 Network Camera Technical Specifications Function/group General Item Specifications Video buffer 48 MB pre- and post alarm Video access from web browser Camera live view Video recording to file (ASF) Customizable HTML pages Windows Vista, XP, Windows 7, and Server 2008 DirectX 9c or higher For other operating systems and browers see www.axis.
AXIS Q1614 Network Camera Technical Specifications Function/group Item Specifications Warranty Axis 3-year warranty and AXIS Extended Warranty option, see www.axis.com/warranty Connectors I/O connector 4–pin terminal block for: • • • • 0 V DC (-) Auxiliary power (DC output) Digital Input Digital Output Function Pin 0 V DC (-) 1 DC output Configurable (Input or Output) 1 2 3 4 Notes Specifications 2 Can be used to power auxiliary equipment. Note: This pin can only be used as power out.
AXIS Q1614 Network Camera Technical Specifications Audio Connector 3.5 mm audio connectors (stereo) 3 2 1 1 Tip 2 Ring 3 Sleeve Audio Input Balanced Microphone Hot (+) In/Unbalance Microphone In/Line In Balanced Microphone Cold (-) In Ground Audio Output Line out (mono) Ground RS485/422 Connector Two 2-pin terminal blocks for RS485/RS422 serial interface.
AXIS Q1614 Network Camera Technical Specifications • Heavy network utilization due to poor infrastructure. Bandwidth affected. • Viewing on poorly performing client computers lowers perceived performance. Frame rate affected.
User Manual AXIS Q1614 Network Camera © Axis Communications AB, 2013 - 2014 Ver. M4.4 Date: June 2014 Part No.
