AXMINSTER Code 501260 Hobby SERIES AWDS12H 300mm Disc Sander
Index of Contents Page No Index of Contents 02 Declaration of Conformity 02 What’s in the Box 03 General Instructions for 230V Machines 04 Specific to Sanding Machines 05-06 Assembly 07-08-09 Specifications 10 Parts Illustraction and Description 11 Changing the Sanding Disc 12 Maintenance 12 Illustrated Parts Breakdown 13 Illustrated Parts List 14 Notes 15 Declaration of Conformity Copied from CE Certificate The undersigned, F. Nispel authorised by Laizhou Chunlin Machinery Co., Ltd. No.
What’s in the Box Model Number DS12 Box Containing: 1 No. 300mm Disc Sander (Sanding Disc & Table Fitting) 1 No. Flexible Extraction Hose. Bag 1 Containing: 2 No. Moulded Lift & Shift Locking Handles 2 No. Locking Handle Spring/Screws Bag 1 Containing: 1 No. Mitre Fence 1 No. Instruction Manual Having opened the box, remove all the components stowed in the packaging. Place these carefully to one side.
General Instructions for 230V Machines Good Working Practices/Safety The following suggestions will enable you to observe good working practices, keep yourself and fellow workers safe and maintain your tools and equipment in good working order. WARNING! KEEP TOOLS AND EQUIPMENT OUT OF THE REACH OF YOUNG CHILDREN! Mains Powered Tools (General) /Disc & Belt Sander Primary Precautions These machines are supplied with a moulded 13 Amp. Plug and 3 core power cable.
Specific to Sanding Machines Warning! The sanding disc cannot be declutched from the belt and vice versa, both functions are active when the machine is running. Remember this, and do not leave loose objects of any description, on the machine if it is going to be used. Once the sander is mounted, carry out any setting operations, (mitre, tilt...), and remove all tools used in the setting operations (if any) and place safely out of the way.
Specific to Sanding Machines Check that the belts or discs are undamaged; torn edges can pick up on the workpiece and will cause the medium to tear, often very rapidly with accompanying sharp flapping edges. Always offer the workpiece to the belt/disc so that the motion carries the work against the restraining surface, (i.e. the work stop or the table, (use the left hand side of the disc). Do not press too heavily against the sanding surface, all this will do is slow the sander down.
Assembly In order to reduce the footprint of the machine for packaging, several items are dismounted from the machine and need to be re-affixed. Locate the two moulded locking handles and the two spring/screws, insert the handles over the table swivel studs one on either side of the table (See fig 1). Fig 1 Swivel stud Moulded locking handle Introduce and screw the spring/screw through the locking handle into the swivel stud using a screwdriver (See figs 2-3) Fig 2 Spring/Screw Continues Over....
Assembly Screwdriver Fig 3 DO NOT OVERTIGHTEN! Lift the table until the scale pointer reads 90˚degrees on the scale, place a 90˚ degrees square on top of the table and adjust until both table and sanding disc are at 90˚ degrees, then clamp the table in position by pulling the locking handles down.
Assembly Locate the mitre fence and slide it into the “T” slot machined into the table. (See fig 5) Mitre fence Fig 5 “T” slot Locate the flexible extraction hose and fit one end of the hose over the dust extraction outlet, push firmly home. (See fig 6) The other end of the hose can be attached to a dust extraction system. The Sander is ready for use.
Specification Model Code Rating Power Speed Diameter of Disc Table Size Table Tilt Dust Extraction Outlet Overall L x W x H Weight 10 AWDS12H 501260 Hobby 750W 230V 1ph 1,420rpm 300mm 445 x 155mm 45° 63mm 500 x 470 x 420mm 30kg
Parts Illustraction and Description PUSH DOWN Motor On/Off switch Disc brake Disc guard Sanding disc Sanding table Mitre fence Flexible extraction hose Rubber feet Table locking handle 11
Changing the Sanding Disc DISCONNECT THE MACHINE FROM THE MAINS SUPPLY! 1) Remove the sanding disc guard by removing the two Phillips screws on top of the guard. 2) Remove the two locking handles on either side of the sander. 3) Remove the swivel studs and lift the table away. 4) Lift the edge of the disc and, gripping firmly, peel the disc away from the plate; turning the plate as required to free the entire disc. 5) Remove and throw away.
Illustrated Parts Breakdown 13
Illustrated Parts List Item 01 Decription Sanding Disc Specification Qty Item 300mm 1 15 Decription Specification Qty Pan Head Bolt 4 02 Base 1 16 Lock Assembly 2 03 Motor 1 17 Disc Cover Outlet 1 1 18 Dust Extraction Outlet adaptor 1 19 Table 1 20 Mitre Fence 1 04 Key 05 Brake Base A5 x25 1 06 Brake Frame 1 07 Pin 1 08 Handle 1 09 Spring 1 10 Washer 1 11 Screw 12 Hex Headbolt M5 x 10 1 4 13 Trunion 2 14 Reference washer 2 14 21 Screw 1
Notes 15
The Axminster guarantee is available on Hobby, Trade, Industrial, Engineer, Air Tool & Axcnc Technology Series machines It’s probably the most comprehensive FREE guarantee ever- buy with confidence from Axminster! So sure are we of the quality, we cover all parts and labour free of charge for three years! • Look for the icon and put your trust in Axminster • No registration necessary - just keep your proof of purchase • Optional Service Plan for Industrial Series machinery Great value & easy-to-use, perfec
