Code 501269 RDC100H Vacuum Extractor Axminster Tool Centre, Unit 10 Weycroft Avenue, Axminster, Devon EX13 5PH axminster.co.
Index of Contents Page No Index of Contents Declaration of Conformity What’s in the Box General Instructions for 230V Machines Specific Safety for Dust Extractors Specification Assembly Workshop Setup Illustration and Parts Description Changing the Micron Filter Bag Maintenance Parts Breakdown Parts List 02 02 03 04 05 06 06-07 08-09 10-11 12-13 13 14 15 Declaration of Conformity Copied from CE Certificate The undersigned, Galen Chun authorised by Qingdao DandD Electromechanical Technnologies Co., Ltd.
What’s in the Box Model Number RDC100H 1 No. Vacuum Extractor with filter and micron bag fitted. A 1 No. Flexible Hose B 1 No. Flexible Hose Clamps C 1 No. 100mm Adaptor Moulding D 4 No. Micron Filter Bags E Code 210091 1 No. Instruction Manual Having unpacked your vacuum extractor and its accessories please dispose of any unwanted packaging properly. The packaging is biodegradable.
General Instructions for 230V Machines Good Working Practices/Safety The following suggestions will enable you to observe good working practices, keep yourself and fellow workers safe and maintain your tools and equipment in good working order. ! WARNING!! Primary Precautions KEEP TOOLS AND EQUIPMENT OUT OF THE REACH OF YOUNG CHILDREN Mains Powered Tools and Machines These machines are supplied with a moulded 13 Amp. Plug and 3 core power cable.
Specific Safety for Dust Extractors DO NOT use this machine as a vacuum cleaner, try to keep the waste medium to wood by-products. Do not uplift workshop floor debris (stones, nails, screws, paper etc., etc). Be aware that wood dust is an explosive medium. DO NOT allow any ‘naked light’ source to occur anywhere near the machine. This includes cigarettes, matches, etc, and do not place the machine near any unprotected light bulbs, that could possibly get broken.
Specification Model Product Code Rating Power Air Flow Noise Level Particle Size Hose Diameter Overall L x W x H Weight RDC100H 501269 Hobby 1,100W 180m³/hr 85dB(A) 1 micron 100mm 400 x 400 x 700mm 10kg Assembly Your Vacuum Extractor is fully assembled, except for the Flexible Hose and 100mm Adaptor Moulding, you will find all parts inside the vacuum extractor, by removing the vacuum motor head. You will also require a flat ended screwdriver.
Assembly Dust extraction out 4 3 A C B Lift the motor head assembly and remove all the parts from inside the drum, if you haven’t already done so. Replace the motor head and clamping ring (A). Locate one of the two hose clamps (C), place over one of the ends of the hose (B) and push the hose over the dust extraction outlet. C 6 5 B D Secure the hose in position by tightening the hose clamp (C)using a flat edge screwdriver. Locate the 100mm Adaptor Moulding (D) and the remaining hose clamp (C).
Workshop Setup This machine will cope with waste shavings from most bench-top machines and the smaller floor standing machines, especially bandsaws, circular saws, bench top surface planers and hand-held power tools (with the accessory power tool hose kit), (code 718085). Below are two examples showing the vacuum extractor connected to a hand-held sander and floor standing bandsaw.
Workshop Setup 63mm Dust Extraction Kit (Code 410063) Another option is a ducting system package complete with elbows, blast gates and adaptors for connecting up your machines to a workshop extractor. Simply fix a horizontal pipe to the wall or ceiling with the clips supplied and then take branch pipes to exactly where the extraction points are needed in the workshop, using the T junctions and 63mm flexible hose. The picture above shows the vacuum extractor connected to the 63mm dust extraction kit.
Illustration and Parts Description Motor head clamp Carryng handle Filter and micron bag Motor assembly Hose Drum 100mm Adaptor moulding 10
Illustration and Parts Description ON OFF ON/OFF Switch 11
Changing the Micron Filter Bag ! DISCONNECT THE VACUUM EXTRACTOR FROM THE MAINS SUPPLY 1 2 A A Remove the motor head by unlatching the motor clamping ring (A). 3 Remove the motor head clamping ring (A) and place safely aside. 4 Micron bag and filter assembly Lift the motor head assembly away from the drum. 5 Remove the micron bag and filter from the motor assembly and clean the motor assembly and filter using an air line or vacuum cleaner.
Changing the Micron Filter Bag 7 8 Replace the micron bag and filter assembly, push firmly so the assembly is flush up against the motor casing. Lower the motor head assembly back onto the drum, replace the motor clamping ring and lock it, securing it in position. Connect the Vacuum Extractor to the mains and continue with operation. Maintenance ! DISCONNECT THE VACUUM EXTRACTOR FROM THE MAINS SUPPLY Weekly •CHECK the inlet duct, remove any accumulated debris.
Parts Breakdown 14
Parts List ITEM NAME QTY 1 Shaving Drum Container 1 2 Motor Head Clamping Ring 1 3 Cartridge Filter 1 4 Motor 1 5 Screw ST5.
Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local recycling centre and place into the appropriate recycling bin. Only for EU countries Do not dispose of electric tools together with household waste material.
