Code 505088 T-2000CK 2hp Cyclone Extractor
INVENTORY LIST C1 B F A G A1 Q O B1 T H Z N I J E K R L W C D M S P X V Y A. Reducing Collector N. Lower Leg (Short-2 off) B. Round Collector C. 7”*4” Y-adapter O. Upper Leg (3 off) P. PE Bag (Small for under filter) D. Housing Cover E. Connecting Bracket (3 off) Q. Lower Dust Drum R. Upper Dust Drum F. Main Housing Assembly S. PE Bag (Big for waste drum) G. 1-1/2” Hose T. Lower Leg (Long-1 off) H. Round Clamp (Large) U. Wheels (2 off) I. Round Clamp (Small) V.
Machine Assembly Step 1 Assemble Round Collector Main Housing Place the main housing (F) upside down, and place the Round Collector (B) on the housing on motor side with inlet Chute positioned as shown Fixing by 12 off,3/16” x 3/8” Cap screws around drum and 6 off, 1/4 Hex head Bolts on leg supports Notice: The Position of Inlet 12 of Cap Screws 6 off Hex Head Bolts Step 2 Assemble Upper Leg with Round Collector Fit three pcs Upper Legs (O)in the tube bracket on the round collector as shown.
Step 3 Assemble Connecting tube Fit the connecting bracket tube (E) with upper leg (O), and fixing by 5/16” Button HD screw Step 4 leg tube Fit the lower leg tube (N and T) with connecting tube, and fixing by 5/16” Button HD screw A1 Step 5 Assemble long Support Tube brace Fit two long Support brace (A1) as shown, and fixing by 5/16” Button HD screw A1 6
Step 6 Assemble Short Support Tube brace Fit the short Support Tube Brace (B1) as shown, and fixing by 5/16” Button HD screw B1 Step 7 Assemble 7” (U) Wheel in short lower leg (N) as shown, and fixing by 3/8” Nut Step 8 Assemble 3” Caster(Y) in the Long lower leg (T) as shown, 7
Step 9 Fit Switch & Gage 9A) Assemble the Magnetic Switch Place the Magnetic Switch under the Main Housing as photo and fix by 5/16” Flange Bolt. 9B) Fit the Gage as photo shows, and tighten by 1/4” Flange Bolt.
Step 13 Fit top lid (D) Please the main Housing cover with Main Housing and fit as photo 3/16" x 3/8 socket head cap screws. Step 14 Assemble canister filter cleaning Handle (M) Place Handle on the Canister and fix by the M6 set Screw.
Step 17 . Place the upper dust drum (R) onto the lower dust drum (Q) as shown, with suction pips on bottom drum opposite Window of top drum. Fit the big round clamp (H). Fix the Round Clamp by 1/4”*4” L Hex Screw and Nut. When fitting top drum half on top of bottom base centralize it the best you can then fit clamp and tighten it progressively while lightly tapping on the clamp ringwith a soft face hammer around the outside. Step 18.
Step 20 Put the big PE Bag (S) inside the dust drum. And try to get air between the Drum and PE bag out as much as possible Step 21 Assemble reducer cone to drum lid Assemble Lid (Z) and top cone (A) as shown. And Fix by 1/4” Flange HD Screw, and 1/4”Flange Nut Place this assembly on top of the mobile collection drum to assist in the next step Step 22 Reducing Collector Assembly When d rum and lid assembled under the machine. Lift the Reducing Collector, and assemble under Machine to connect together.
Step 23 Small PE Bag Install Place the small PE bag (P) as shown on canister filter bottom and fixing by the Belt clamp (X) 1 Step 24 Assemble the 1-1/2 Hose Slide the 1-1/2” hose (G) on the 38mm tube of the round collector and fix by one of the1-3/4” hose clamp.(J) Step 25. Slide the 1-1/2” hose the other side as shown on the 38mm tube of the dust drum and fix by the 1-3/4” hose clamp (J).
Part List 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 41 42 44 46 47 48 50 51 52 Motor Main Housing Aluminum Impeller Reducing Collector PE Bag PE Bag Ball Caster Round Clamp Hose Switch Plate Magnetic Switch Hose Clamp Inlet Steel Clamp Impeller Washer Handle Square Pad PC Board Inlet Cap Lower Fixing Plate Flapper Bearing Fixing Plate Washer Flange Nut Lower Drum Round Clamp Upper Drum Hex Bolt Rivet 4-2 Canister Filter
NO. Description Specification Q'TY 53 Connecting Tube 3 54 Lower Leg 3 55 Power Cord W/ Plug 1 56 N Type Handle 1 57 Cap Screw 3/16"* 3/8" 27 58 Main Spindle 1 59 Connecting Spindle 1 60 Cap Screw M6* 12 2 61 Bearing Fixing Plate 1 62 Hex Bolt M6* 16 1 63 Flange Bolt 1/4"*1/2" 8 64 Flange Bolt 1/4"* 1/2" 14 66 Nut M5 4 67 Drum Lid 1 68 Cap Nut 1/4" 2 69 Phil.
General Machinery Safety Instructions Read this entire Manual before using this machine. 1. Read the entire Manual before starting machinery. Machinery may cause serious injury if not correctly used. 2. Always use correct hearing protection when operating machinery. Machinery noise may cause permanent hearing damage. 3. Machinery must never be used when tired, or under the influence of drugs or alcohol. When running machinery you must be alert at all times. 4. Wear Correct Clothing.
Wood Dust Collector Safety Instructions Read this entire Manual before using this machine. 1. Maintenance. Make sure the Dust collector is turned off and disconnect from the main power supply and make sure all moving parts have come to a complete stop before any inspection, adjustment or maintenance is carried out. 2. Dust collector Condition. Dust collector must be maintained for a proper working condition. Never operate a Dust collector that has damaged or worn parts.
The Axminster guarantee is available on Hobby, Trade, Industrial, Engineer, Air Tools & Axcnc Technology Series machines It’s probably the most comprehensive FREE guarantee ever- buy with confidence from Axminster! So sure are we of the quality, we cover all parts and labour free of charge for three years! • Look for the icon and put your trust in Axminster • No registration necessary - just keep your proof of purchase • Optional Service Plan for Industrial Series machinery AXMINSTER Hobby SERIES Great v
