Installation Instructions / Warranty Wallbar Sets Unica’E 06890XX0 Croma E 75 3-Jet 06494XX0 Croma E 75 2-Jet 06496XX0 Clubmaster 04044XX0 Monsoon II 04043XX0 Raindance E 120 3-Jet 04098XX0
Unica’E Wallbar Croma E 75 3-Jet Croma E 75 2-Jet Follow the installation instructions (see page 4) when drilling the mounting holes.
Technical Information Croma E 75 3-Jet handshower 2.5 gpm Full, massage, turbo massage Croma E 75 2-Jet handshower 2.5 gpm Full, turbo massage Clubmaster handshower 2.5 gpm Full, massage, soft aerated Raindance E 120 AIR handshower 2.5 gpm AIR, Whirl AIR, Balance AIR Monsoon II handshower 2.5 gpm Full, massage, turbo massage Installation Considerations • For best results, Hansgrohe recommends that this unit be installed by a licensed, professional plumber.
Wallbar installation 1 Remove the screw covers from the wallbar. Position the wallbar in the desired location. Mark the positions of the screw holes (1). Place the wallbar in a safe location. Drill the holes with a 6 mm bit (2). Do not drill into existing water lines! (3) Install the anchors. Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. Install the wallbar using the screws and washers. Install the screw covers.
06494XX0/06496XX0 only: Place a black rubber washer in one end of the handshower hose. Connect this end to the wall supply (not included). Place a second washer in the other end of the hose. Connect this end to the handshower. Rest the handshower in the holder. Install the vacuum breaker (Models 04043XX1/04044XX1/04098XX1 only) Install the vacuum breaker and washer on the water supply. Place a hose washer in one end of the hose. Connect this end of the hose to the vacuum breaker.
User Instructions Do not remove the handshower by pulling “out” on it. This will damage the handshower holder. To remove the handshower from the holder, pull “up” on it until the nut at the end of the handshower hose clears the holder, before pulling “out”. To move the slider up and down the bar, loosen the slider knob. Move the slider to the desired position. Tighten the knob. To change the angle of the handshower, use the handshower as a lever. Pull or push the handshower to the desired position.
Handshower user instructions Clubmaster only: Turn the function ring until the desired function is achieved.
Scale Removal This handshower incorporates the Quick Clean cleaning system. If scale deposits are noticed in the spray channels, turn the water on lightly and rub the spray channels with a finger or a sponge. Clubmaster only: When the spray modes are changed, pins push deposits from the normal spray channels. If scale deposits are noticed on the spray face, pour about 3/4” of a commercial scale remover, such as Lime-Away™ or CLR™,into a shallow dish. Dilute the remover according to the label instructions.
Replacement Parts 3 6 2 7 5 1 8 4 9 1 2 3 4 5 6 7 8 9 slider 88590XX0 screw cover 88534XX0 tile spacer (optional) 96184000 handshower hose, 63” 28276XX0 handshower hose, 72” 88625XX0 Croma E 75 2-jet handshower 28570XX1 Croma E 75 3-jet handshower 28573XX1 Clubmaster handshower 28525XX1 Raindance E 120 3-jet handshower 28507XX1 soap dish 69007000 hose washer 98058000 XX = color 00 = chrome 62 = oil rubbed bronze 82 = brushed nickel 83 = polished nickel 93 = polished brass
Cleaning Recommendation for Hansgrohe Products Modern lavatory faucets, kitchen faucets, and showers consist of very different materials to comply with the needs of the market with regard to design and functionality. To avoid damage and returns, it is necessary to consider certain criteria when cleaning.
5 years, with respect to AXOR products. THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: A. Conditions, malfunctions or damage not resulting from defects in material or workmanship. B.
www.hansgrohe-usa.com US - Installation Instructions • Part No. 90965601-02 • Revised 10/2008 Hansgrohe, Inc. • 1490 Bluegrass Lakes Parkway • Alpharetta, GA 30004 Tel.