DMX LED light effect with 4 scan mirrors User manual 1
Safety precautions WARNING: This unit may cause serious injury to the eyes when used incorrectly. It is therefore strongly advised to read this user manual carefully, to get familiance yourself with the functions of this device. WARNING: This unit must be operated by, or under the supervision of an adult. This device is not suitable for children. WARNING: Do not look directly into the beam from a short distance. This may cause serious injury to the eyes.
Box contents Box contents 1x TDC 444 fixture 1x power cable Unit and accessory inspection - Always use the supplied power cable to connect the unit to a power supply. If the cable appears broken or has visible damage, do not use it. - If the unit is not going to be used for a longer period of time, disconnect it from the power supply and store it in a dust-free environment. - Always check the unit for possible damage before use.
Device overview 1. Moving mirror 2. Beam output 3. Adjustable bracket 4. Ventilation slots 5. Fan 6. IEC Power inlet with integrated fuse holder 7. Control panel display with MENU, UP and DOWN buttons 8. Sound sensitivity potentiometer 9. Safety eye, for optional safety cable 10. Built-in microphone for sound active mode 11. DMX input (3P XLR) 12.
Setting up the unit To activate the unit, connect the included power supply with the unit and a suitable 230V, 50 Hz power outlet. The unit will activate directly after it is plugged in to a wall outlet or other power source. Give the scanner time to calibrate the stepping motors, which are used to determine the position of the mirror. You may hear and see some shaking, which is normal. The stepping motors use an end point to determine the beginning and end of their movement.
Set the correct address on the digital display, you are able to choose a value between 001 and 255. When a DMX-signal is received, a blinking red dot on the display is active. Working time: hour: It is possible to see the total working time of this fixture, by activating this feature. Test mode: test: The unit will test all its internal programs. Channel mode: Chnd This mode changes the DMX channel mode between 8, 12 and 17.
294 215 236 214 235 255 Gobo 0 Gobo 11 Gobo 12 Channel 2: Horizontal movement (Pan) for Mirror 1 Channel 3: Vertical movement (Tilt) for Mirror 1 Channel 4: Select gobo for Mirror 2 Start value 0 8 29 50 70 91 112 132 153 174 294 215 236 End value 7 28 49 69 90 111 131 152 173 193 214 235 255 Function No function Gobo 1 Gobo 2 Gobo 3 Gobo 4 Gobo 5 Gobo 6 Gobo 7 Gobo 8 Gobo 9 Gobo 0 Gobo 11 Gobo 12 Channel 5: Horizontal movement (Pan) for Mirror 2 Channel 6: Vertical movement (Tilt) for Mirror 2 Channe
294 215 236 214 235 255 Gobo 0 Gobo 11 Gobo 12 Channel 11: Horizontal movement (Pan) for Mirror 4 Channel 12: Vertical movement (Tilt) for Mirror 4 17 channel DMX mode Channel 1: Dimmer intensity Start value 0 128 End value 128 255 Function No function Dimmer 0-100% Channel 2: Strobe slow/fast (only works when CH1 is set to 128-255) Channel 3: Select gobo (channel 4 must be set to off) Channel 4: Select rotating gobo (channel 3 must be set to off) Channel 5: Gobo rotation Start value 0 128 End value
Installation and maintenance Mounting the bracket A pre-mounted hanging bracket is provided, with screwknobs at both sides of the scanner. This bracket can be used to install the unit to a fixed structure, such as a T-bar or truss. Installing the scanner in a hanging position When you wish to hang the scanner against a wall, ceiling or beam, make sure to use proper installation tools and let a skilled technician install the scanner for you.
The mirror and lens can be cleaned with a non-aggressive glass cleaning solution, but is not recommended. Ayra recommends to clean the mirror and lens with a fine brush, while removing dust and/or dirt with a vacuum cleaner. Do not touch the mirror and lens with your fingers, as this may cause fingerprints which are harder to remove. Checkup To prevent dangerous situations, make sure your fixture is in optimal condition before using it.
Technical specifications - LED light effect with four moving mirrors Light source: 60x 5mm LEDs (16x red, 20x green, 20x blue, 4x amber) 8, 12 or 17 DMX-channels 3-pin XLR in- and output Music controlled mode with internal microphone Microphone sensitivity adjustable Working modes: music controlled, DMX, test, master/slave Power consumption: 132W continuous, 246W max.