Ayre V-6x Owner’s Manual A y r e V-6x Power Amplifier
Table of Contents Welcome to Ayre . . . . . . . . . . . . . . . . . . . . . . . 2 Connections and Installation . . . . . . . . . . . . . . . . . . . . 3 Controls and Operation . . . . . . . . . . . . . . . . . . . . . 7 Numbers and Specifications . . . . . . . . . . . . . . . . . . 10 In Case of Trouble . . . . . . . . . . . . . . . . . . . . . 11 Statement of Warranty . . . . . . . . . . . . . . . . . . . . 14 A Place for Notes . . . . . . . . . . . . . . . . . . . . . .
Welcome to Ayre Please send in your warranty registration card so we can stay in contact with you. Your Ayre V-6x offers a significant advance in the musical performance of high-fidelity equipment. The warmth and immediacy of a live performance are apparent from the first listening. The combination of superb resolution and a natural, relaxed quality will draw you into the music, time and time again. This level of performance has been implemented using the highest level of workmanship and materials.
Connections and Installation The Ayre V-6x is easy to hook up and use. The following guidelines will ensure that the installation goes smoothly. Location Do not stack the Ayre V-6x directly with other components, as this may restrict the air flow or induce hum into the audio circuitry. A good location for your power amplifier is on the floor between your loudspeakers, or in an open-backed cabinet, or on a shelf. The Ayre V-6x produces a moderate amount of heat during operation.
Inputs When you have a choice, a balanced connection will usually offer slightly higher sound quality. The power amplifier can be driven by a surround-sound processor or preamplifier. There are two sets of input connectors for each installed channel of the Ayre V-6x. The RCA connectors accept signals from unbalanced sources, while the XLR connectors are for balanced sources. Only one set of inputs (balanced or unbalanced) may be connected at a time.
V-6 Power Amplifier Unbal Input Sel Bal ¡Attention! — Balanced Outputs Do Not Connect Output Terminals to Ground S.N.
Controls and Operation The Ayre V-6x has a front panel control for normal stand-alone operation. The amplifier may also be controlled via a “trigger” input in a home-theater. Power Switches The master power switch on the rear panel also incorporates a circuit breaker. There are two power switches on the Ayre V-6x. The master power switch on the rear panel is normally intended to be left on at all times. The front-panel switch selects between the “Standby” and “Operate” modes.
In the green “Standby” mode the output stage is turned off, while the input circuitry remains powered. This allows the unit to warm up quickly for optimal sonic performance, while reducing the power consumption from 60 watts per installed channel to 10 watts total. Trigger Input Use a 1/8" mini-phone plug with a positive voltage of between +5 and +12 VDC at the tip to operate the trigger input.
Repeating this procedure will revert the unit back to the level-sensitive mode, as indicated by the status LED slowly flashing red (about 1 Hz). In the pulse-sensitive mode, a positive-going pulse edge will toggle the amplifier between the “Standby” and “Operate” states, duplicating the action of the front-panel switch. In this mode the front panel switch is always operative. However, operating the unit with the front panel switch may put the unit out of “synch” with the control device.
Numbers and Specifications Power Output 150 watts per channel continuous into 8 ohms 300 watts per channel continuous into 4 ohms Input Impedance 100 kΩ – unbalanced inputs 200 kΩ – balanced inputs (100 kΩ per phase) XLR Input Polarity Gain Pin 1 = Ground Pin 2 = Non-inverting (Positive) Pin 3 = Inverting (Negative) 26 dB Frequency Response DC - 200 kHz Power Consumption 10 watts in standby mode 60 watts per installed channel in operating mode, (no signal) Dimensions Weight 18" W x 19" D x 7-¾
In Case of Trouble The Ayre V-6x provides comprehensive protection for both the amplifier and your loudspeakers, including faults that may occur in your source components. Overheating Sensors located on each audio module will shut the amplifer off if the heatsink temperature reaches 175° F (80° C). If the unit is operated at high playback levels with insufficient ventilation, the internal temperature may become too high, triggering the thermal protection circuitry.
Rail Fuses Indicator LEDs on the rear of the unit will glow red when one of the fuses blows. Please refer fuse replacement to a qualified service technician. Internal fuses on the power supply rails of each channel protect the loudspeakers from excessive current, as well as the amplifier from short-circuits. If one of these rail fuses blows, that channel will fail to operate, although the front panel LED will typically continue to glow blue. Do not remove the amplifier cover.
“Warm-Up” mode, and power is immediately removed from the output stage. After correcting the suspected fault condition, a press of the front panel button is required to return the unit to the green “Standby” condition. A second press of the button will restore the unit to the blue “Operate” mode. If the fault is still present when the front panel switch is pressed the second time, the unit will immediately revert to the red “Warm-Up” mode.
Statement of Warranty Please take a moment to fill out and return the enclosed warranty registration card. Your Ayre V-6x power amplifier is warranted against defects in workmanship and materials for a period of five years from the date of purchase. This warranty is transferable to subsequent purchasers within the original five-year period. All warranty claims must be made through an authorized Ayre dealer or distributor. Warranty Statement 1. Ayre Acoustics, Inc.
or to Ayre’s authorized agent. 3. Ayre reserves the right to inspect any product that is the subject of any warranty claim prior to repairing or replacing it. Final determination of warranty coverage lies solely with Ayre. Out-of-warranty claims will be billed for labor, materials, return freight, and insurance as required. Any product for which a warranty claim is accepted will be returned to the purchaser and the cost of shipping and insurance will be factory prepaid within the boundaries of the USA.
6. Ayre does not authorize any third party, including any dealer or sales representative to assume any liability of Ayre or make any warranty for Ayre. The unit must not have been altered or improperly serviced. The serial number on the unit must not have been altered or removed. 7. Warranty registration cards must be completed and mailed to Ayre within 30 days of purchase. Ayre may, at its option, require from the purchaser valid proof of purchase (dated copy or photocopy of dealer’s original invoice).
A Place for Notes 16 Rev. 1.
Ayre Acoustics, Inc. 2300-B Central Avenue Boulder, Colorado 80301 www.ayre.
