Owner’s Manual M odel # F-1350-FPT OUTDOOR FIRE PIT TABLE R R C R US ANS Z21.
REPLACEMENT PARTS LIST A B I C D G F E K J H PART A B C D E F G H I J K L M N O P Q DESCRIPTION QUANTITY Burner Cover 1 Table Top 1 Burner 1 Burner Bracket 1 Side Panel 1 1 Side Panel 2 1 1 Side Panel 3 (Burner Controls) 1 Side Panel 4 (Door Frame) 1 Conneting Rod 1 Gas Tank Br acket (side) 1 Gas Tank Support (bottom) Bolt(8*55mm)/Nut(M8)/Washer/Spring Washer 4 Bolt(6*18mm)/Washer(M6) 12 Screwdriver 1 Wrench 1 Allen Wrench 1 2boxes/4bags Glass Beads 2
HARDWARE CONTENTS L N M Bolt(8*55mm) Nut(M8) Washer Spring washer Qty. 4 Bolt (6*18mm) Washer Qty. 12 O Qty. 1 Q P Wrench Qty 1 SAFETY INFORMATION Screwdriver Allen wrench Qty 1 Glass Beads 2boxes/4bags Please read and understand this entire manual before attempting to assemble, operate or install the product . This appliance has been tested to and complies with the ANS Z21.97-2010, Outdoor Decorative Gas Appliances CGA CR 9 7-003Outdoor Gas Fireplaces.
SAFETY INFORMATION DANGER DANGER · · EXPLOSION - FIRE HAZARD Keep solid combustibles, such as building materials, paper or cardboard, a safe distance away from the fire pit as recommended by the instructions. · Provide adequate clearances around air openings into the combustion chamber. · Never use the fire pit in spaces which do or may contain volatile or airborne combustibles, or products such as gasoline, solvents, paint thinner, dust particles or unknown chemicals.
SAFETY INFORMATION WARNING WARNING California Proposition 65 Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects, and other reproductive harm. · This product is fueled by propane gas. Propane gas is invisible, odorless, and flammable. An odorant is normally added to help detect leaks and can be described as a "rotten egg”smell. The odorant can fade over time so leaking gas is not always detectable by smell alone.
OPERATION CHECKLIST Operation Checklist For a safe and pleasurable heating experience, perform this check before each use. Before Operating: 1. I am familiar with entire owner’s manual and understand all precautions noted. 2. All components are properly assembled, intact and operable. 3. No alterations have been made. 4. All gas connections are secure and do not leak. 5. Wind velocity is below 10 mph. 6. Unit will operate at reduced efficiency below 40 F/4.44°C 7.
ASSEMBLY INSTRUCTIONS NOTE: It is best to assemble the fire pit with two people . 1.Connect Side Panels ( E , F , G , H ) with Bolt ( 6 * 18mm ) / Washer ( M6 ) ( M ) as shown in Figure 1 using Allen Wrench .( make sure that holes1 , 2 can be found on the side panels and assemble as Figure 1 , the two holes help fix the Gas Tank Bracket and Gas Tank Support in the Step 2 .) (NOTE:Don't put the Bolts on too tight.) 1 G hole2 hole1 Hardware Used M Bolt(6*18mm) x8 F E Washer (M6) x8 P H 2.
ASSEMBLY INSTRUCTIONS 3. Place the Burner Bracket (D) onto the assembled panels as shown in Figure 3. Move the Burner (C) so that the burner controls can face Panel G. (NOTE: There is a HOLE at the top of Panel G to accommodate the control knob on the burner.) Make sure the switch of the burner is alignedwith the (G). 3 C hole control 4.. Attach the Connecting rod (I) to the Burner(C)using Opening pin through the hole at the top of the side panel (G) .
ASSEMBL ASSEMB LY INST INSTR RUCTIONS 5. Attach the 4 - Bolt(8*55mm) (L) to the holes of the Table Top (B). Then align the Bolts with the holes in the Burner Bracket and assembled panels and insert the Bolts through the holes. Attach the Table Top to the Burner Bracket and assembled panels with 4 - Washer/Spring Washer/Nuts (L). 5 (NOTE:Tighten all the Bolts and Nuts.) Hardware Used L Bolt (8*55mm), Nut(M8), Washer, Spring washer x4 O N 6. Pour the Glass Beads (Q) around the Burner (C).
ASSEMBL ASSEMB LY INST INSTR RUCTIONS 7. Connect the hose and regulator to the cylinder. The propane gas and cylinder are sold separately. Use a standard 20 lb. propane cylinder only. Use this fire pit only with a propane vapor withdrawal supply system. See Chapter 5 of the standard for storage and handling of liquefied petroleum gas, ANSI/NFPA 58. Your local library or fire department should have this book.
ASSEMBLY INSTRUCTIONS A dented, rusted or damaged propane cylinder may be hazardous and should be checked by your cylinder supplier. Never use a propane cylinder with a damaged valve connection. The propane cylinder must be constructed and marked in accor dance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT) or the standard f or cylinders, spheres and tubes for transportation of dangerous goods and commission, CAN/CSA-B339.
OPERATION INSTRUCTIONS Leak Test WARNING Perform all leak tests outdoors. Extinguish all open flames. NEVER leak test when smoking. Do not use the fire pit until all connections have been leak tested and do not leak. Hose / Regulator connection Regulator / Cylinder connection 1. Make 2-3 oz. of leak test solution (one part liquid dishwashing detergent and three parts water). 2. Apply several drops of solution where hose attaches to regulator. 3.
OPERATION INSTRUCTIONS DANGER WARNING • CARBON MONOXIDE HAZARD • For outdoor use only. Never use inside house, or other unventilated or enclosed areas. This fire pit consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life. Very hot while in operation! Never lean over the fireplace while in use. Failure to comply with these instructions may result in serious bodily injury.
OPERATION INSTRUCTIONS WARNING FOR YOUR SAFETY Be careful when attempting to manually ignite this fire pit. Holding in the control knob for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition. When fire pit is ON: Burner will display tongues of blue and yellow flame. These flames should not be yellow or produce thick black smoke, which would indicate an obstruction of airflow through the burners. The flame should be blue with straight yellow tops.
CARE AND MAINTENANCE Gas odor with extreme yellow tipping of flame. Fire pit does NOT reach the desired temperature. Fire pit glow is excessively uneven. Fire pit makes popping noises. Spiders and insects can nest in burner or orifices. This dangerous condition can damage fire pit and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles. Carbon deposits may create a fire hazard.
TROUBLESHOOTING PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION Propane cylinder is frosted over Wait until the propane cylinder warms up and becomes unfrosted Blockage in orifice Clear blockage Control knob is not in ON position Turn control knob to ON Gas pressure is low Turn cylinder valve OFF and fill the cylinder Outdoor temperature is less than 40ºF and tank is less than 1/4 full Use a full cylinder Control knob fully ON Check burner and orifices for blockage Carbon build-up Dirt or film on
