OUTDOOR FIRE PIT MODEL #GSF-PR-PC R R R C US Precaution! The Powder Coating paint process has become the most common widely used application in the outdoor furniture category. Unfortunately powder coating is extremely sensitive to Humidity and Moisture. A simple process to protect your furniture, especially flat surfaces is to apply a simple coat of good quality car wax prior to using. If this process is done every few months it will protect your furniture for years to come. ANSI Z21.97-2014/CSA 2.
HOW TO REMOVE OXIDATION Rub the surface with automotive rubbing or polishing compound to abrade away oxidation. 1. Apply a coat of automotive paste wax to the surface. 2. Allow the wax to dry for a few minutes. 3. Remove residue and polish surface with a clean cloth. Oxidation can be a problem on metal painted surfaces, since the outermost layers of paint are constantly exposed to air and water.
PACKAGE CONTENTS A I B C J D K E F L G M H N PART A B C D E F G H I J K L M N 3 DESCRIPTION Knob Lid Table Side Panel (Right) Back Panel Gas Cylinder Block Belt Side Panel (Left) Bottom plate Glass (One Pack) Front top plate Burner Assembly Control Knob Door Panel Door Handle QUANTITY 1 1 1 1 1 1 1 1 1 1 1 1 1 1
HARDWARE CONTENTS AA Philips screwdriver Qty. 1 BB M4 X 5 Screw Qty. 3 CC M4 X 8 Screw Qty. 2 DD EE M6 X 12 Screw Qty. 8 M5 X 8 Screw Qty. 4 N Door Handle Qty. 1 A Knob Qty. 1 SAFETY INFORMATION Please read and understand this entire manual before attempting to assemble, operate or install the product. If you have any questions regarding the product, please call customer service at 1-888-775-1330, 7 a.m. - 4 p.m., PST, Monday - Friday.
SAFETY INFORMATION DANGER DANGER • EXPLOSION - FIRE HAZARD • Keep solid combustibles, such as building materials, paper or cardboard, a safe distance away from the fire pit as recommended by the instructions. • Provide adequate clearances around air openings into the combustion chamber. • Never use the fire pit in spaces which do or may contain volatile or airborne combustibles, or products such as gasoline, solvents, paint thinner, dust particles or unknown chemicals.
SAFETY INFORMATION WARNING WARNING California Proposition 65 Combustion by-products produced when using this product contain chemicals known to the State of California to cause cancer, birth defects, and other reproductive harm. • This product is fueled by propane gas. Propane gas is invisible, odorless, and flammable. An odorant is normally added to help detect leaks and can be described as a “rotten egg” smell. The odorant can fade over time so leaking gas is not always detectable by smell alone.
ASSEMBLY INSTRUCTIONS 1. 1. Attach the door handle (N) to the door panel (M) using 2 M4X5 screws. 1 M Hardware Used AA Philips screwdriver BB M4X5 screw x1 N x2 2. Attach the gas cylinder block belt (F) to the back panel (E) using 2 M4X8 screws. 2 E Hardware Used AA CC Philips screwdriver M4X8 screw x1 F x2 3. Attach the knob (A) to the lid (B) using 1 M4X5 screw.
ASSEMBLY INSTRUCTIONS 4. Loosen the screws attached to the base (H), left side panel (G), and right side panel (D). 4 G H 5. Place the right and left panels over the loosened screws, then push the panels back. Tighten the screws. 5 D G H The hole for assembling the door 6. Slide the back panel (E) over the screws on both side panels .Tighten the screws.
ASSEMBLY INSTRUCTIONS 7. Attach the door (M) to the base with the spindle at the bottom of the door into the hole and the top spindle into the hole of the front top plate (J). Use 4 M6X12 screws to attach the front top plate to the right and left side panels. Hardware Used AA J M Philips screwdriver DD M6X12 screw 7 x1 x4 8. Line up the screw holes on the table (C) with the left and right side panels. Use 4 M6X12 screws to attach the table tightly.
ASSEMBLY INSTRUCTIONS 10. Plug the knob (L) onto the pole of the gas valve. 10 L 11. Put the gas tank into the gas housing of the fire pit. Use the gas cylinder block belt to fasten the gas tank in place. 11 12. Put the fire glass into the burner.
ASSEMBLY INSTRUCTIONS 13 13. Put the lid (B) on the burner. B 14. Connect hose and regulator to cylinder. The propane gas and cylinder are sold separately. Use a standard 20 lb. propane cylinder only. Use this heater only with a propane vapor withdrawal supply system. See chapter 5 of the standard for storage and handling of liquefied petroleum gas, ANS/NFPA 58. Your local library or fire department should have this book.
ASSEMBLY INSTRUCTIONS A dented, rusted or damaged propane cylinder may be hazardous and should be checked by your cylinder supplier. Never use a propane cylinder with a damaged valve connection. The propane cylinder must be constructed and marked in accordance with the specifications for LP gas cylinders of the U.S. Department of Transportation (DOT) or the standard for cylinders, spheres and tubes for transportation of dangerous goods and commission, CAN/CSA-B339.
OPERATION INSTRUCTIONS Leak Check WARNING • Perform all leak tests outdoors. • Extinguish all open flames. • NEVER leak test when smoking. • Do not use the fire pit until all connections have been leak tested and do not leak. Hose / Regulator connection Regulator / Cylinder connection 1. Make 2-3 oz. of leak check solution (one part liquid dishwashing detergent and three parts water). 2. Apply several drops of solution where hose attaches to regulator. 3.
OPERATION INSTRUCTIONS WARNING DANGER • CARBON MONOXIDE HAZARD • For outdoor use only. Never use inside house, or other unventilated or enclosed areas. This fire pit consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life. Very hot while in a operation! Never lean over the fireplace while in use. Do not touch tile of spark guard while the fire pit is in operation, wait until the fire pit has cooled down after use.
OPERATION INSTRUCTIONS WARNING FOR YOUR SAFETY Be careful when attempting to manually ignite this fire pit. Holding in the control know for more than 10 seconds before igniting the gas will cause a ball of flame upon ignition. When fire pit is ON: Burner will display tongues of blue and yellow flame. These flames should not be yellow or produce thick black smoke, indicating an obstruction of airflow through the burners. The flame should be blue with straight yellow tops.
OPERATION INSTRUCTIONS 9. Fire pit is away from gasoline or other flammable liquids or vapors. 10. Fire pit is away from windows, air intake openings, sprinklers and other water sources. 11. Fire pit is at least 24 in. on rear and at least 24 in. on sides from combustible materials. 12. Fire pit is on a hard and level surface. 13. There are no signs of spider or insect nests. 14. All burner passages are clear. 15. All air circulation passages are clear. 16.
CARE AND MAINTENANCE Gas odor with extreme yellow tipping of flame. Fire pit does NOT reach the desired temperature. Fire pit glow is excessively uneven. Fire pit makes popping noises. Spiders and insects can nest in burner or orifices. This dangerous condition can damage fire pit and render it unsafe for use. Clean burner holes by using a heavy-duty pipe cleaner. Compressed air may help clear away smaller particles. Carbon deposits may create a fire hazard.
TROUBLESHOOTING If you have any questions regarding the product, please call customer service at 1-888-775-1330, 7 a.m. - 4 p.m. (PST), Monday - Friday.
ONE-YEAR LIMITED WARRANTY CUSTOMERS IN USA Do not return this product to the store where you purchased it. Please call 1-888-775-1330 for assistance. CUSTOMERS IN CANADA IMPORTANT Only return this product to the store if it was purchased within 90 days. If you have problems after 90 days of purchase, please CALL 1-888-775-1330 DATED PROOF OF PURCHASE REQUIRED FOR WARRANTY SERVICE. This product is inspected, tested and carefully packaged to minimize the chance of damage during shipment.
REPLACEMENT PARTS LIST For replacement parts, call our customer service department at 1-888-775-1330, 7 a.m. - 4 p.m., EST, Monday - Friday.