Assembly Of K/D Wheels P M8 nut bracket with Use PCs M8X15mm bolts and M8 nuts to Wheels connect the bracket with wheels fo the base . Then fasten them.
TABLE OF CONTENTS CANON .. Heater Stand and Location .. Gas Requirements Leakage Test Operation and Storage e, Cleaning and Care s Parts and Specifications Assembly Parts and Procedures ..
® s 0060090 . L Y CAUTION PLEASE READ CAREFULLY THE FOLLOWING SAFETY GUIDELINES BEFORE OPERATION. Do not use the panic heater for indoors, as it may cause personal injury or property damage. This outdoor heater is not intended to be installed on recreational vehicles and/or boats. The installation must conform with local daces o, in the absence of local codes, to the National Fuel Gas Case, ANS! 2223, 1-1988, Propane installation Code. Installation and repair should be done by a qualified service person.
HEATER STAND AND LOCATION . The heater is primarily for outdoor use only. Always ensure that CEILING adequate fresh air ventilation is provided. sum . Always maintain proper clearance to combustible materials, i.e. top 18" G and sides 24" minimum. . Heater must be placed on label firm ground. E . Never aerate heater in an explosive atmosphere like in areas where ® gasoline or other flammable liquids or vapors are stored. .
OPERATION AND STORAGE TO TURN ON THE HEATER Turn on the valve on the gas supply cylinder completely. . Press and tum the variable control knob to PILOT position {counter-clockwise 90°). . Press down the variable control knob and hold for 30 seconds. While holding down the variable control knob, press the ignite button several times unit the pilot fame lights. Release the variable control knob after the pilot flame lights. ww Note: .
CLEANING AND CARE Wipe off powder coated surfaces with soft, moist rag. Do not clean heater with cleaners that are combustible or corrosive. Remove debris from the burner to keep it clean and safe for use. Cover the burner unit with the optional protective cover when the heater is not in use. PARTS AND SPECIFICATIONS 813mm Reflector. Flame screen. [ Buber base N2 Alr admittance fe =N Gas valve controvert / Base of control house ¥ 2210mm Tank Tank housing suppose-i i i Stand v4.
A Construction and characteristics Transportable terrace/garden heater with dank reusing Casing in steel with powder-coating or stainless steel Gas hose connections with metal clamp (screw caps for Germany) Stainless steel flame screen Haas emission from reflector B. Specifications For outdoor use ably Use propane ar butane gas only Max. wattage: 13000 watts (41000 Btu) Min. wattage: 5000 watts (17000 Btu) Consumption: 450 girth — 870 fuhrer With CE & CSA certificates C.
ASSEMBLY PARTS Tools needed: .
ASSEMBLY PROCEDURES STEP 1-1. Put the 3 pes post brackets on each position on the base as shown in the picture. 1-2. Use 3 pcs bolts to join the post brackets and stand. STEP 2-1. Puttee post on the top of 3 pcs post brackets. 2-2. Use 6 pes bolts and nuts to connect the post to the 3 pes post brackets. Tighten the bolts and nuts, STEP Place the tank housing on the stand.
STEP 4 4-1. Fit the gas hosepipe nut to the burner gas inlet connector. 4-2. Tighten the gas hose/pipe nut and gas inst thread. 4-3. Fix the completed boomer unit to the post by 4 pcs bolts. STETS §-1. Check whether the connection of vertical post and burner are assembled according fo instructions, and all bots and nuts are tightened, 5-2. Put washer @8 mm on each reflector support bolt, STEP 6 6-1. Fasten the reflector with 3 pcs washers and 3 pes M8 mm mods nuts.
STEP? 7-1. Bring up the tank housing and rest it on the post plate. 7-2. Connect the regulator to the gas tank and tighten it with adjustable wrench, 7-3. Connect the end thread of net gas hose to the regulator. 7-4. Put LPG gas tank on the stand.