PATIO HEATER OWNER’S MANUAL IMPORTANT Read this manual carefully before assembling, using or servicing this FOR MODELS: HSS-A R R heater. Keep this manual for future reference.
Contents DANGER General Safety Information....................................... 1 Assembly Instructions DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Components & Hardware........................................ 3 Additional Requirements ........................................ 3 WARNING Installation Process Step1 - Attach Wheel Assembly to Base.................
DANGER DANGER • EXPLOSION - FIRE HAZARD • Keep solid combustibles, such as building materials, paper or cardboard, a safe distance away from the heater as recommended by the instructions. • Provide adequate clearances around air openings into the combustion chamber. • Never use the heater in spaces which do or may contain volatile or airborne combustibles, or products such as gasoline, solvents, paint thinner, dust particles or unknown chemicals.
WARNING • This product is fueled by propane gas. Propane gas is invisible, odorless, and flammable. An odorant is normally added to help detect leaks and can be described as a “rotten egg” smell. The odorant can fade over time so leaking gas is not always detectable by smell alone. Assembly Instructions Components Remove all components from package. Reflector Panel(3) Reflector Plate • Propane gas is heavier than air and leaking propane will sink to the lowest level possible.
WARNING California Proposition 65 Combustion by products produced when using this product contain chemicals known to the state of California to cause cancer, birth defects, and other reproductive harm. Used in Hardware Picture Qty Description Step(s) 4 Small Bolt 4 (For models without . . Washer Small Screw Large Flat 9 Washer Small Flat 9 Washer Assembly time: 0.
Lay Bucket inside of Base and screw on large nut. Step 5 – Tabletop Installation Put the Plastic nut & Fastening piece through the post in order.Put the Tabletop through the post as show. Tighten with Philips screwdriver. Fill Sand . To improve the stability , please fill the bucket with Sand. Step 3 – Attach Cylinder Housing to Base Attach Cylinder Housing Loosely to Base with 8 pcs M5X10 bolts. Put the Plastic connecting through the post as show.
. Step 7 – Attach Head Assembly to Post 9 Req’d Small Screw s Screw off 4 small bolts. 4 Req’d Small Bolts Head Assembly .. . . . Load Head Assembly by inserting hose into post. Insert Head Assembly into post. . 9 Req’d Small Flat Washers Control knob should be above decal on post. 9 Req’d Cap Nuts Slide one Small Flat Washer over threaded end of screw and screw on Cap Nut loosely. Attach Head Assembly to post, and loosely install four small bolts. Tighten bolts securely.
.. Step 9 – Attach Reflector Assembly to Studs Slide 3 Large Flat Washers over threaded end of Studs. 6 Req’d Large Flat Washers .. The minimum permissible gas supply pressure of 10 W.C. is required for purpose of input adjustment. Support Heater. 3 Req’d Wing Nuts Locate Reflector Assembly on 3 studs. Install large flat washers on studs & securely tighten wing nuts but do not over-tighten! . . . . . .
Leak Check Operation WARNING DANGER • Perform all leak tests outdoors. • Extinguish all open flames. • CARBON MONOXIDE HAZARD • NEVER leak test when smoking. • Do not use the heater until all connections have been leak • For outdoor use only. Never use inside house, or other tested and do not leak. unventilated or enclosed areas. This heater consumes air (oxygen). Do not use in unventilated or enclosed areas to avoid endangering your life. DANGER • EXPLOSION - FIRE HAZARD . . . .. .. .
. . .. .. . . . Before Turning Gas Supply ON: Your heater was designed and approved for outdoor 4 visible through Viewing Hole. 5 Release Control Knob after 30-60 seconds. Pilot Light will remain lit. If not, return to step 1. use only. Do NOT use it inside a building, garage, or any other enclosed area. Push and release the igniter button until pilot flame is 6 Turn Control Knob to ON. Main Burner will light Make sure surrounding areas are free of combustible immediately.
If you experience any ignition problem please consult “Troubleshooting” on page 11. Caution: Avoid inhaling fumes emitted from the heater’s first use. Smoke and odor from the burning of oils used in manufacturing will appear. Both smoke and odor will dissipate after approximately 30 minutes. The heater should NOT produce thick black smoke. Note: The burner may be noisy when initially turned on. To . . . Shut Down: Turn Control Knob clockwise to Pilot.
Troubleshooting If the problem is: And this condition exists: Then do this Cylinder valve is closed Open valve Blockage in orifice or pilot tube Clean or replace orifice or pilot tube Air in gas line knob in) for not more than 1 - 2 minutes or Open gas line and bleed it (pressing control Pilot won’t light until you smell gas Low gas pressure with cylinder valve Note: Heater operates at reduced efficiency below 40ºF Turn cylinder valve OFF and replace fully open Use match to light pilot; o
.. .. . . Gas odor with extreme yellow tipping of flame. Heater does NOT reach the desired temperature. Heater glow is excessively uneven. Heater makes popping noises. . . . Store heater upright in an area sheltered from direct contact with inclement weather (such as rain, sleet, hail, snow, dust and debris). If desired, cover heater to protect exterior surfaces and to help prevent build up in air passages. Never leave LP cylinder exposed to direct sunlight or excessive heat.
