AZATOM ® iPunch 2 Docking Station with Bluetooth® USER MANUAL www.AZATOM.
AZATOM ® Thank you for purchasing the AZATOM® iPunch 2 Docking Station with Bluetooth. This compact modern speaker has been designed and developed here in the UK to give great quality sound and value. AZATOM® uses the latest Digital Sound Processing (DSP) technology which digitally filters the audio signal to produce a very high quality sound. The iPunch 2 also has the latest amplifier to improve the tone of the music and produce deeper bass.
Controlling your iPunch 2 1. 2. 3. 4. AC Power Connector (DC input 9V) Line out Line in (When using FM radio, the supplied Audio cable works as an FM antenna) Dimmer (The Blue LED has 3 brightness settings – press this button to scroll through the different settings) 5. Standby button 6. Mode / Source selection buttons (choose between iPod, FM, Line-in or Bluetooth mode) 7. Previous track / “Rewind” / FM Tuner (Down) 8. Volume Down ( - ) 9. LED Screen / Remote control window 10. iPod / iPhone Dock 11.
Setting up your iPunch 2 Connect the power adapter with the input socket to the rear of the speaker. Once connected to the mains, press the Play/Pause button. (The remote control can be used to place the speaker into standby mode by pressing the Play/Pause button for 3 seconds). Note: In standby mode, the stored radio stations will be saved. If disconnected from the power supply, the stored radio stations will be lost and will need to be stored again.
2) On your audio device, switch on Bluetooth (sometimes, on your device, you will have to switch the Bluetooth off and back on, in order for it to actively search). The speaker ® ® name is: AZATOM iPunch. Select the AZATOM iPunch in order to connect to the speaker. Note: If prompted for a pair code, enter “0000” – the iPunch 2 does not require a code for modern devices, however, older devices will be required to enter one.
Using the Remote Control The speaker supports a fully-functioning remote control which has a range of 5 metres. Before using the remote control, remove the film from the battery pack within the battery compartment. The remote control will not work until the plastic film has been removed. 1. Remote sensor 2. Standby button 3. Previous playlist button 4. Next playlist button 5. Battery compartment 6. Down button on the iPod / iPhone / FM radio 7. Up button on the iPod / iPhone / FM radio 8.
Troubleshooting Problem Solution There is no sound coming from my iPunch 2 speaker • Make sure the power cord is properly connected to the back of the iPunch 2 system and that the system is plugged into the AC power outlet. • Ensure the Source / Mode “M” button is set correctly. • Press the Play/Pause button on the unit and on the remote control. • Increase the system volume. • Increase the volume on your connected device • Remove your iPod/iPhone from the dock, wait 5 seconds, then reconnect it.
Specifications Maximum Output Power Audio Inputs Power Input Frequency Response Signal-to-Noise Ratio Channel Separation Channel Imbalance FM Frequency Range Bluetooth Standard Bluetooth Protocol Bluetooth Sensitivity Bluetooth Transmitting Power Wireless Transmitting Range Remote Control Distance Remote Control Angle Remote Control Power Supply 30W (15W+15W） THD=10% 3.5mm Jack iPod Dock Connector 9V/2000mA AC Power Adapter 120-18,000Hz (±3dB) ≥60dB ≥40dB ≤3dB 87.5-108MHz v.2.1+EDR A2DP1.
Safety Information 1. Do not install this equipment in a confined space such as a book case or similar unit, and ensure the area remains well ventilated. The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table-cloths, curtains etc. 2. WARNING: Only use attachments/accessories specified or provided by the manufacturer (such as the exclusive power adapter, battery etc.). 3.
