Specifications

ManualsBrandsAzden ManualsHeadphones1000BT

User’s Guide

1000URX • 1000URX\AB • 1000URX\VM • 1000URX\Si

1000BT • 1000XT

ENHANCED BROADCAST PERFORMANCE

UHF WIRELESS SYSTEM

Azden Corporation, 147 New Hyde Park Road, P.O. Box 10, Franklin Square, NY 11010

vox - 516.328.7500 • fax - 516.328.7506 • email - azdenus@azdencorp.com

P1020-05

Printed in USA

SPECIFICATIONS

1000URX - 1000URX\AB - 1000URX\Si - 1000URX\VM

RF Carrier Frequency Range 121 steps ~ 723.000 - 735.000MHz

MicroComputer Controlled PLL Synth.

Effective Operating Range 200 - 300 ft ~ 60 - 100m

Frequency Response 50 - 15kHz (± 1.5dB)

RF Sensitivity (12dB SINAD) 1.2

μμ

μV

Adjacent Channel Selectivity > 73dB (± 250kHz)

Image Rejection > 93dB

IF Rejection > 93dB

Audio THD < 0.8%

Audio Output +4dBm ± 40kHz Deviation (-40dBm ± 5kHz Deviation for 1000URX\Si)

Output Impedance Line - 600

Ω Ω

Ω ~ MIC - 600

Ω (Ω (

Ω (300

ΩΩ

Ω for 1000URX\Si)

Signal/Noise Ratio > 62dB (± 5kHz Deviation)

Power Requirements 11 - 15V DC @ 220mA (10 - 17V DC @ 200mA for 1000URX\Si)

Dimensions (1000URX) 3.3 (W) x 3.9 (H) x 1.2 (D) inches

84 (W) x 100 (H) x 30 (D) mm

Operating Temperature Range 32

- 113

F ~ 0

- 45

Weight 9.88 ounces ~ 280g for 1000URX

15.87ounces ~ 450g for 1000URX\AB

8.81ounces ~ 250g for 1000URX\AB

1000BT

Output Power 20mW

Max Modulation Sensitivity -4dBm

MIC Level / Imped. -60dBm / 2.2k

Ω Ω

Ω (± 5kHz Deviation)

Power Requirements 9V DC (Alkaline) @ < 62mA

Dimensions 2.5 (W) x 3.85 (H) x 1.0 (D) inches

63 (W) x 98 (H) x 27 (D) mm

Weight w/Battery 5.64 ounces ~ 160g

1000XT

Output Power 20mW

Max Modulation Sensitivity (ECM -- Dynamic) +20dBM ~ 0dBm

MIC Level / Imped. (ECM) -35dBm / 2.2k

Ω Ω

Ω (± 5kHz Dev.)

MIC Level / Imped. (Dynamic) -55dBm / 2.2k

Ω Ω

Ω (± 5kHz Dev.)

Power Requirements 9V DC (Alkaline) @ < 60mA

Dimensions 1.57 (W) x 4.4 (H) x 1.57 (D) inches

40 (W) x 112 (H) x 40 (D) mm

Weight w/Battery 6.7 ounces ~ 190g

Due to constant improvements, specifications are subject to change without notice.

Licensing

Licensing of this, or any Azden wireless equipment is the user’s responsibility. The ability to receive a license

depends largely on the user’s classification, application and frequency. Contact the appropriate agency (FCC in

the USA) for further information.

Summary of content (8 pages)

PAGE 1
SPECIFICATIONS 1000URX - 1000URX\AB - 1000URX\Si - 1000URX\VM RF Carrier Frequency Range 121 steps ~ 723.000 - 735.000MHz MicroComputer Controlled PLL Synth. Effective Operating Range 200 - 300 ft ~ 60 - 100m Frequency Response 50 - 15kHz (± 1.5dB) μV RF Sensitivity (12dB SINAD) 1.2μ Adjacent Channel Selectivity > 73dB (± 250kHz) Image Rejection > 93dB IF Rejection > 93dB Audio THD < 0.
PAGE 2
The 1000URX Receiver D. Input Level Adjustment This screwdriver adjustment [i] controls the input level of the microphone. Counterclockwise rotation reduces the input gain while clockwise rotation increases the input gain. E. Display In addition to showing the frequency and channel number, the display [l] also shows other useful information. 1 7 8 The LCD segments on the left show the approximate remaining battery life (from 1 to 3 segments) with 3 segments meaning maximum battery power.
PAGE 3
USING THE 1000XT TRANSMITTER’S CONTROLS AND DISPLAY A. Power The POWER ON/OFF switch [k] turns the 1000XT ON or OFF. B. Audio Prior to first turning the 1000XT ON it is best to set the AUDIO switch [j] to OFF. When you are ready to begin transmitting, switch to ON. The OFF position acts as a ‘mute’ that maintains the RF signal but turns off the audio. 10 3 4 5 6 7 8 9 Phontom Power Switch C. MIC Connector/Locking Ring This 3-pin XLR connector [e] is the microphone input.
PAGE 4
TABLE OF CONTENTS 1000URX RECEIVER VIEW .............................................................................................. i INTRODUCTION .............................................................................................................. ii RECEIVER (1000URX) SETUP ....................................................................................... 1 Powering the 1000URX ....................................................................................................
PAGE 5
G. Display (continued) life (from 1 to 3 segments) with 3 segments meaning maximum battery power. The bottom segment will blink when the battery power falls to less than 6.2V and indicates that it is time to replace the battery. Azden recommends the use of Alkaline batteries only. Across the top of the display, up to 5 segments will illuminate depending on the strength of the transmitted audio signal - from 2 (weak) to 5 (strong). The first (left) segment will light when the ST.BY switch is turned to ON.
PAGE 6
RECEIVER (1000URX) SETUP (continued) A. Attaching the antennas to the 1000URX: To attach the high-gain antennas to the 1000URX, fit the BNC connector on the antenna to the receiver [c], press down and rotate clockwise. To remove the antennas, rotate the antenna’s BNC connector counterclockwise and pull up. B.
PAGE 7
SETTING THE TRANSMITTING FREQUENCY ON THE 1000BT Before the 1000BT can be used, it and the associated receiver have to set to the same frequency. This can be accomplished on the 1000BT transmitter by first setting the LCD display to one of two views - ‘Frequency’ or ‘Channel’. To do this, after installing a fresh battery, turn the 1000BT to the ON position [e].
PAGE 8
THE 1000URX\AB and 10000URX\VM The 1000URX\AB is a specially developed version that integrates the Anton/Bauer “Gold Mount” to power the receiver. The 1000URX\VM is a specially developed version that integrates the IDX battery-mount to power the receiver. All of the functions and controls on the 1000URX remain unchanged except for the method of powering the receiver.