Specifications

ManualsBrandsAzden ManualsMicrophones and systems30BT

320 SYSTEM

User’s Guide

320UPR • 30BT • 30HT • 30XT

ON-CAMERA

UHF WIRELESS MICROPHONE SYSTEM

Azden Corporation, 147 New Hyde Park Road, P.O. Box 10, Franklin Square, NY 11010

vox - 516.328.7500 • fax - 516.328.7506 • email - azdenus@azdencorp.com

P1070-01

Printed in USA

Specifications

Due to constant improvements, specifications are subject to change without notice.

320UPR Receive

Frequency Range UHF 240 Selectable Frequencies (794-805.950MHz)

Type of Reception Dual-channel Receiver

Oscillator PLL Synthesized

RF Squelch Level 13dBµV

Frequency Response 50Hz – 15kHz

S/N Ratio >70dB “A” Weighted

Audio Out MIC Level – Unbalanced – 3.5mm Mini-Jack

Batteries 2 “AA” Alkaline (2 x 1.5V) - 3-4 hours runtime

2 “AA” rechargeable Ni-MH or Ni-Cd (2 x 1.2V)

External Power 6VDC @ 0.5A

Dimensions 2.87"W x 4.45"H x 1.59"D (73 x 113 x 40.5 mm)

Weight Approx. 9.17oz (260g) w/batteries

30BT Body-pack Transmitter

Frequency Range UHF 240 Selectable Frequencies (794-805.950MHz)

Oscillator PLL Synthesized

RF Power 15mW

Frequency Response 50Hz – 15kHz

Max. Deviation ±40kHz @ 1kHz Modulation, MIC Input – 11dBm

Batteries 2 “AA” Alkaline (2 x 1.5V) – 8-10 hours runtime

2 “AA” rechargeable Ni-MH or Ni-Cd (2 x 1.2V)

Dimensions 2.52"W x 3.94"H x 1.06"D (64 x 100 x 27 mm)

Weight Approx. 4.54oz (160g) w/batteries

30XT Plug-In Transmitter

Frequency Range UHF 240 Selectable Frequencies (794-805.950MHz)

Antenna Internal

Max. Input level -7dBm

RF Power 15mW

Input Impedance 6k ohms

Audio Adjust. Range -63dBm to 18dBm

Battery 1 9V Alkaline – 6-8 hours runtime

Dimensions 1.57"W x 1.57"H x 3.9"L (40 x 40 x 99 mm)

Weight Approx. 6.4oz (181.4g) w/battery

30HT Handheld Microphone/Transmitter

Frequency Range UHF 240 Selectable Frequencies (794-805.950MHz)

Oscillator PLL Synthesized

RF Power 15mW

Frequency Response 50Hz – 15kHz

Max. Deviation ±40kHz @ 1kHz Modulation, MIC Input – 65dBm (dev ±5kHz)

Batteries 2 “AA” Alkaline (2 x 1.5V) – 8-10 hours runtime

2 “AA” rechargeable Ni-MH or Ni-Cd (2 x 1.2V)

Dimensions Φ1.89" x 9.23"L (48 x 234.5 mm)

Weight Approx. 4.23oz (245g) w/batteries

Summary of content (4 pages)

PAGE 1
Specifications 320UPR Receiver Frequency Range Type of Reception Oscillator RF Squelch Level Frequency Response S/N Ratio Audio Out Batteries External Power Dimensions Weight 30BT Body-pack Transmitter Frequency Range UHF 240 Selectable Frequencies (794-805.950MHz) Oscillator PLL Synthesized RF Power 15mW Frequency Response 50Hz – 15kHz Max. Deviation ±40kHz @ 1kHz Modulation, MIC Input – 11dBm Batteries 2 “AA” Alkaline (2 x 1.5V) – 8-10 hours runtime 2 “AA” rechargeable Ni-MH or Ni-Cd (2 x 1.
PAGE 2
Operating the system 19 6 Because this is a frequency agile system, the receiver and transmitter must be on the same channel number. To change the channel number, use the tip of the provided tool and press the UP or DOWN button to the desired channel. Make sure both the receiver and transmitter are on the same channel. 4 320UPR Receiver 3 21 20 9 18 17 7 8 5 After installing new batteries, mount the receiver to your video camera with the supplied shoe mount or hook & loop fastener.
PAGE 3
(21) LCD Display: The display will light up when the power is turned “ON”. The LCD display shows the following information. Channels number: 001 to 240 Battery Condition: Using a 3 step indicator – 1(Low) to 3 (High) To change the channel number, use the tip of the tool provided and press the UP or DOWN button until the desired channel number appears (001 to 240). Once the desired channel number has been selected on the transmitter, set the receiver to the same channel number.
PAGE 4
A) Make sure that you use 2 different channel numbers that are at least 10 numbers apart. This will prevent possible crosstalk between the 2 channels being used. For example: If you use channel number 10 for one transmitter, use channel number 20 for the other transmitter. The 2 channels on the receiver must also be set on the numbers 10 and 20. (14) MIC Input Jack Plug the supplied EX-503L microphone into the MIC input jack and tighten the collar until snug (DO NOT OVERTIGHTEN).