Installation Guide
Page 10
Installing Column Wrap
Tools Required
Painting
Parts
Fastening
• AZEK Column Wraps are not structural and are not intended for load bearing
applications.
• Manufactured edges of the column wrap are sharp and should be handled with
care.
• AZEK Column Wrap should be installed in accordance with the local building
codes and the installation guidelines included below. AZEK Building Products
Inc. accepts no liability or responsibility for the improper installation of this
product. Failure to install AZEK Column Wrap in accordance with applicable
building codes and this Installation Guide may lead to personal injury, affect
product performance and void the product warranty.
Cutting
• AZEK Column Wrap can be cut using the same tools used to cut
lumber.
• Carbide tipped blades designed to cut wood work well. Avoid using
ne tooth metal cutting blades.
• Rough edges from cutting may be caused by excessive friction, poor
board support, worn or improper tooling.
• For best results, use fasteners designed for wood trim and wood siding.
These fasteners have a thinner shank, blunt point, and full round head.
• To take advantage of the performance of AZEK products, use a highly
durable fastener such as stainless steel or hot dipped galvanized.
• The fasteners should be long enough to penetrate the solid wood
substrate a minimum of 1 1/2".
• Standard nail guns work well with AZEK Trim products. If using
pneumatic tools, the air pressure should be regulated so fasteners
slightly penetrate the surface.
• AZEK COLUMN WRAP FASTENING CONSIDERATIONS
(Use one of the following):
• #7 trim screw
• 16 gauge T-nail
• 15 gauge round head
• Fasteners should be a minimum of 1 1/2” in length
• AZEK Column Wrap does not require paint for protection, but
accepts and holds paint very well.
• If you choose to paint, use a 100% acrylic latex paint with colors
having a Light Reective Value (LRV) of 55 or higher.
• For darker colors (LRV of 54 or lower) use paints with heat
reective characteristics specically formulated for use on vinyl/
PVC products. These paints/coatings are designed to reduce
excessive heat gain.
• WARNING: It is recommended that should you choose to paint a
darker color (LRV of 54 or lower) all aforementioned installation
steps should be followed.
• Follow the paint manufacturers recommendations for use and
compatibility with AZEK Column Wrap.
• AZEK Column Wrap surfaces must be clean, dry, and void of any
foreign material such as dirt, oil, grease or other contaminates that
may come from normal handling, storage and/or installation prior
to painting.
• Moisture cycling is a main reason for paint failure on wood. Since
AZEK material absorbs almost no moisture, paints last longer on
AZEK products than it does on wood.
• Since AZEK products have almost no moisture absorption, paints
may take longer to cure on AZEK material than on wood. Generally
paints on AZEK products will be dry to the touch quickly, but may
take up to 30 days to fully cure depending on the humidity and
temperature.
WARNING! Please read all instructions completely before starting any part of the installation.
• AZEK Column Wrap may not be suitable for every application. It is the sole
responsibility of the installer to be sure that AZEK Column Wraps are t for
the intended use. Since all installations are unique, it is also the installer’s
responsibility to determine specic requirements in regards to each application.
• AZEK Building Products recommends that all applications be reviewed by a licensed
architect, engineer, or local building ofcial before installation. If you have any
questions or need further assistance, please call AZEK Customer Service at 877-ASK-
AZEK (877-275-2935) or visit our website at www.AZEK.com.
Storage & Handling
• Care should be taken in handling the individually wrapped column
wraps to prevent tearing of tape or cracking at miter lock corner joints.
• Store AZEK Column Wrap on a at level surface.
• Since AZEK Trim products are more exible than wood, they may
conform to uneven surfaces. Ensure that storage areas, as well as all
framing and substructures, are at and level to minimize uneven surfaces.
• AZEK Column Wrap has a density comparable to pine and should be
handled in similar fashion as pine to avoid damage.
• Units of AZEK products are shipped from the manufacturer in a
protective covering. If covering has been removed, take care to keep
product free of dirt and debris at jobsite. If product gets dirty, clean
after installation.
Gluing
• For best results, eliminate debris from grooved joints prior to applying
glue so that joints can maintain good contact with each other.
• For best results, apply adhesive to all joints to prevent joint
separation.
• The glued joint should be secured to allow adequate bonding time.
Do not use a fastener to secure the joint.
• AZEK Adhesive has a working time of approximately 10 minutes and
will be fully cured in at least 24 hours.
• If standard PVC cements are used, these products typically cure
quickly which will result in limited working time and may reduce
adhesive strength.
Ad hes iv e