® .
CONTENTS SAFETY INSTRUCTION AND GUIDELINES P. 1-4 GETTING STARTED P. 5-6 VELOCITY ADJUSTMENT P. 7 REGULATOR ADJUSTMENT P. 8-9 ZERO SYSTEM P. 10-11 ASSEMBLY AND CLEANING P. 12-13 REASSEMBLE REAR INTERNALS P. 14 TROUBLESHOOTING P. 15 KAOS-D SCREW CHART P. 16-17 KAOS-D O-RING CHART P. 18-19 ZeRO SYSTEM P. 20 INLINE REGULATOR P. 21 ON/OFF BOTTOM ASA P. 22 KAOS-D PARTS LIST P. 23 KAOS-D EXPLODED VIEW P.
! WARNING ! IMPORTANT SAFETY INSTRUCTION AND GUIDELINES • This Paintball Marker is NOT A TOY. Misuse can cause serious injury or death. • Recommend 18 years or older to purchase this product. Person under 18 must have adult supervision. • Read this manual, understand and follow the manual instructions for using this product. • Eye and face protection specially designed for paintball use, must be worn by user and persons within range at all times.
! WARNING ! IMPORTANT SAFETY INSTRUCTION AND GUIDELINES • Ensure all air lines and fittings are tightened and secured before installing the air tanks. • Do not shoot at people, animals, houses, cars or anything is not related to the sport of paintball. • Always keep the marker in Safe mode until ready for use. • Fire only 0.68 caliber paintballs with this marker. • Always make sure the bolt is in the un-cocked position when marker is not in use.
! WARNING ! IMPORTANT CO2/ HPA AIR TANK SAFETY INSTRUCTION AND GUIDELINES • Tank valves must be installed or removed by qualified personnel. • All tanks must be retested before the expiration date. • Improper use, filling, storage of this air tank may cause death, serious injury and property damage. • Air tanks must be filled only by properly trained personnel. • Do not over pressurize. Do not expose pressurized tanks to temperatures in excess of 130F° degrees (54°C).
! WARNING ! IMPORTANT CO2/ HPA AIR TANK SAFETY INSTRUCTION AND GUIDELINES STOP IMMEDIATELY CO2 or HPA/ N2 Air tanks will have enough force to fly off and cause serious injury or death if the valve unscrews from the tank head. Look at the valve when removing the tank from the marker’s Bottom ASA (A021). Make sure that the valve is turning with the tank instead of staying with the marker. STOP IMMEDIATELY if valve starts to unscrew from the tank itself.
GETTING STARTED 1. First, place the BARREL BLOCKING DEVICE over the barrel. ® 2. Always point your marker at a “SAFE” direction before use. To use, push the safety button from the “PUSH SAFE” side of the grip frame. Doing this will put the marker in a lock safe mode. To unlock the safe mode, point the marker in the safe direction, and push the safety button towards the “PUSH SAFE” side of the grip frame. 3. Firmly screw in the CO2/ HPA/ N2 air tank to the On/Off Bottom ASA (A091).
6. Check marker’s velocity FPS (Feet Per Second). Turning the Velocity Adjuster (P023) clockwise will increase the velocity. Counterclockwise will decrease the velocity. 7. After playing, take out all paintballs from the hopper. Then detach the hopper from the marker. CAUTION: There may be 1-2 paintballs in the breach area; take a couple more shots in a safe direction to make sure the marker is empty of paintballs. ® 8.
REGULATOR ADJUSTMENT (INCREASE & DECREASE AIR PRESSURE) CLOCKWISE DECREASE VELOCITY COUNTERCLOCKWISE INCREASE VELOCITY To increase the input pressure use the allen wrench to turn the Regulator Adjustment Screw (S032) counterclockwise. To decrease the input pressure use the allen wrench to turn the Regulator Adjustment Screw (S032) clockwise.
NOTE: Regulator is preset at the factory for optimum performance. Fine adjustment of velocity should be done with the velocity adjustor (P023) on page 7. NOTE: Each quarter turn correspond to approximate increase or decrease of 20psi.
ZeRO SYSTEM INSTRUCTION AND ADJUSTMENT WARNING: Never remove the internal of the marker while the air tank is attached with the marker. ® FOR CO2 OPERATION: NOTE: Zenith is optimized for use with HPA, in order to optimize the Zenith for CO2 use, please follow the instructions below. 1. Insert the 3mm allen wrench into the ZeRO Adjustment Screw (Z001). Turn clockwise two full revolutions. 2. To optimize the velocity, make sure the rear velocity adjustment is backed all the way out.
2. To optimize the velocity, make sure the rear velocity adjustment is backed all the way out. Adjust the Inline Regulator (refer to Regulator Adjustment) until the marker is shooting at 250 feet per second over a chronograph. 3. To fine-tune the marker velocity follow the direction on page 9 (refer to Velocity Adjustment) ® ADVANCE ADJUSTMENT: The ZeRO System is a revolutionary combination of the Feather Striker and a redesign of the Valve Engine.
ASSEMBLY AND CLEANING PULL THE TOP COCKING KNOB 1 3 2 WARNING: Never remove the internals of the marker while the air tank is attached with the marker. Always remove all paintballs, loader and air tank before disassembling the marker.
CLEANING AND DISASSEMBLE REAR INTERNALS 1. Lift upward on the Top Cocking Knob at the rear of Delrin Bolt. This will let the Delrin Bolt (P041) slide out from the rear of the receiver. 2. Turn the End Cap (A051) counterclockwise. This will let the End Cap and the marker’s internals to slide out from the rear of the receiver. Remember to place the marker in the de-cock position and place light pressure behind the End Cap during the removal of the End Cap, this way will prevent the internals to spring out. 3.
REASSEMBLE REAR INTERNALS 1. Insert the Feather Striker (P021) thru the rear of the receiver with the O-Ring facing towards the front of the marker and with the hole on the Feather Striker facing upright. While inserting the Feather Striker, apply pressure behind the Feather Striker and at the same time pull the Trigger to let Feather Striker enter the rear chamber of the receiver. 2. Insert the Feather Bumper (P024) thru the receiver and insert the Feather Spring (P022) thru the Feather Bumper. 3.
TROUBLESHOOTING WARNING: Always remove all paintballs, loader and air tank before disassembling the marker. RECOCKING ISSUES Need Lubrication on the Striker O-Ring (R011). ® Striker O-Ring is damaged or missing. Replace a correct O-Ring. The pressure in the tank is too low and needed to be refilled. Dirt or broken paintball shell fragments in the receiver. Check, cleaning, and disassemble rear internals. AIR LEAKS Air leaking from the low pressure chamber.
KAOS-D SCREW CHART SIZE: 1:1 PART NUMBER AND NAME S011 M5 X 10L MAIN BODY SCREW S012 M8 X 8L VALVE RETAINING SCREW S014 M5 X 16L VERTICAL ASA SCREW S015 M3 X 3L DETENT COVER ASA SCREW S016 M4 X 8L GRIP PANEL SCREW S031 M4 X 4 RETAINING SCREW 16
KAOS-D SCREW CHART SIZE: 1:1 PART NUMBER AND NAME S032 M12 X 8L REGULATOR ADJUSTMENT SCREW S091 M12 X 8L ON/OFF BOTTOM ASA RETAINING SCREW S092 1/8-27 NPT ON/OFF BOTTOM ASA HOSE PLUG S093 M5 X 12L ON/OFF BOTTOM ASA SCREW Z031 ZeRO ADJUSTMENT SCREW 17
KAOS-D O-RING CHART SIZE: 1:1 PART NUMBER AND NAME R011 STRIKER O-RING (RED) R012 FRONT VALVE O-RING (CLEAR) R013 AZ O-RING (BLACK) R015 AZ O-RING (BLACK) R016 BARREL O-RING (BLACK) 18
KAOS-D O-RING CHART SIZE: 1:1 PART NUMBER AND NAME R017 END CAP O-RING (BLACK) R031 REGULATOR PISTON O-RING (CLEAR) R032 REGULATOR SWIVEL MOUNT O-RING (BLACK) R033 INNER O-RING (CLEAR) R034 REGULATOR SEAL O-RING (CLEAR) Z021 ZeRO CUP SEAL O-RING (CLEAR) 19
Z001 ZeRO SYSTEM Z031 Z014 ® ZeRO SYSTEM PARTS LIST Z041 NO PART NAME P011 Z011 VALVE ZeRO CUP SEAL STEM ZeRO CUP SEAL ZeRO SPRING Z012 Z014 R015 Z021 R012 FRONT VALVE O-RING (CLEAR) R015 AZ O-RING Z021 ZeRO CUP SEAL O-RING Z012 Z011 R012 Z031 ZeRO ADJUSTMENT SCREW Z041 ZeRO HOUSING P011 R015 20
A062 INLINE REGULATOR R015 REGULATOR PARTS LIST P081 S031 R031 NO PART NAME P081 MAIN REGULATOR HOUSING REGULATOR SWIVEL MOUNT REGULATOR END CAP REGULATOR PISTON REGULATOR MAIN SPRING SEAT SEAL CARRIER P082 P083 P084 P084 P085 P085 P086 P082 R032 R032 R033 P083 R015 AZ O-RING R031 REGULATOR PISTON O-RING R032 REGULATOR SWIVEL MOUNT O-RING R033 REGULATOR INNER O-RING R034 REGULATOR SEAL O-RING R034 P086 S032 S031 S032 REGULATOR RETAINING SCREW REGULATOR ADJUSTMENT SCREW 21
A091 ON/OFF BOTTOM ASA P063 P091 ® A092 R033 S092 A093 S091 ON/OFF BOTTOM ASA PARTS LIST NO PART NAME P063 P091 90 DEGREE MACROLINE HOSE ON/OFF BOTTOM ASA STEM R033 INNER O-RING S091 S092 ON/OFF BOTTOM ASA RETAINING SCREW ON/OFF BOTTOM ASA HOSE PLUG A092 A093 ON/OFF BOTTOM ASA CAP ON/OFF BOTTOM ASA MAIN BODY 22
KAOS DELUXE PARTS LIST NO PART NAME NO PART NAME P011 P021 P022 P023 P024 P031 P032 P041 P051 VALVE FEATHER STRIKER FEATHER SPRING VELOCITY ADJUSTER FEATHER BUMPER BALL DETENT DETENT COVER BOLT ASSEMBLY TWIST LOCK FEEDNECK 90 DEGREE ELBOW MACROLINE HOSE S017 VERTICAL ASA SCREW ON/OFF BOTTOM ASA SCREW P063 P072 R011 R013 R015 R016 R017 S011 S012 S015 S016 STRIKER O-RING (RED) AZ O-RING AZ O-RING BARREL O-RING END CAP O-RING S093 A011 A031 A051 A062 A071 A081 A091 A202 Z001 KAOS BODY VERTICAL ASA
KAOS DELUXE 2011 EXPLODED VIEW A051 P051 R013 P041 ® R017 P023 A011 R016 S015 A202 P024 R011 P031 P022 P021 P032 P032 P011 P031 R015 Z001 PLEASE REFER TO PAGE 23 FOR DETAIL OF ZeRO SYSTEM S015 S012 S011 A031 S011 S016 S017 A081 A071 A062 PLEASE REFER TO PAGE 19 FOR DETAIL OF REGULATOR S093 S016 P063 P072 A091 PLEASE REFER TO PAGE 25 FOR DETAIL OF ON/OFF BOTTOM ASA 24
www.azodin.