Users Manual

ManualsBrandsAzores ManualsNetwork HardwareWi-Fi 6 MESH AP

Overview Product Hardware Description Product Manual

WAN

LAN

Power

WPS

LED

ON/OFF

WPSWAN

ON/OFF

LED Behavior

Scenario

Steady Red

Powering up

Blinking Red

No network cable connected

Blinking Green

Network connection in progress

Steady Green

Function normally and can access the Internet

Blinking Blue

Steady Blue

WPS or Mesh pairing in progress

Reset

Product label

Azores AX1800 Wi-Fi6

Wireless Router

Thank you for choosing our product.

Please read this manual before use.

If you need to change Internet Access method, i.e. from router

to bridge mode, or add a new Mesh AP to your Mesh network,

or need other information, please scan the QR code below to

view the electronic user manual for instructions.

Reset Button Description

Short press (1 second) for reset the router

Long press (5 seconds or longer) for reset to factory default settings

AX1800 Backside illustration

AX1800 Bottom illustration

LED Description:

Pairing successful

Dark No power

Single Router

Mesh Router Set

For single router：Connect the provided network cable from

the AX1800 Router to your home Broadband Gateway

(i.e. cable/DSL modem, PON gateway).

Please refer to SINGLE ROUTER SETUP STEPS for network setup.

For mesh router set: Master AP is used as the main router,

which is to be connected, via provided network cable, to your

home Broadband Gateway (i.e. cable/DSL modem, PON gateway);

Slave AP is used for Wi-Fi network expansion. Please refer to

ONE ROUTER SETUP STEPS (for Master AP) & MESH SETUP

STEPS (for Slave AP) for network setup.

Place the Slave AP at a proper location based on your home

layout. After powering on, Slave AP is all set when the LED is

steady green. To optimize wireless performance, place the

Slave AP in a location that minimizes the barrier (such as

wall, door, and ﬂoor) between the Master and the Slave AP.

We recommend one wall/door/ﬂoor between the two APs.

You can connect the Slave AP to your Master AP via network

cable (preferred method) or wirelessly.

Master AP Slave AP

(1) Connect your Mobile device to Wi-Fi network according to

the Wi-Fi SSID and password sticker on the bottom of

the Master AP.

(2) Download mobile APP software from corresponding App

Store (searching for “azores router”) or Scan the following QR code.

Scan QR code to download Azores Router APP

(3) Login with WiFi password on the bottom of the Master AP

(4) Enter the “My Wi-Fi” menu to modify Wi-Fi conﬁguration or

perform other operations. Note: If you want to use the mobile

device to perform other operations on the router, follow the

instructions on the mobile APP.

I replaced my old router with Azores AP. After

connecting network cable from DSL/PON/Cable

gateway to the Azores AP or Azores Master AP in a

mesh set, the AP’s red LED or Green LED is keep flashing.

What should I do?

When the router is powered on, pushing the “Reset” hole on the

bottom of the device with a needle. The LED starts to ﬂash

green and hold for 5 more seconds. Release when the LED turns

off. The LED will become steady red and will then start to

blink green. Wait for about 2 minutes, then the factory default

reset is completed.

Mobile phones and other devices are connected

to the router but cannot access the Internet

Answer:

Azores Router APP cannot control Azores routing?

Please make sure to use the Azores Router APP to connect to

the Azores router, and use the current Wi-Fi password for login.

If the way that you connect to the network is

different from shown in the figure in "ONE ROUTER

SETUP STEPS", or the IP address conflicts with the

address of the deployed home router/gateway, how to

configure Internet access?

Try put the Router in a bridge mode. Please scan the QR code

(1) Check whether the main router's WAN port is connected to

your Broadband Gateway. The main router’s network port

azoresnetworks.com

POWER

Mesh Setup Steps

Azores Router Mobile APP

Frequently Asked Questions

Master AP Slave AP

Please note the Master AP

has the QR code on the bottom

Quick Start Guide

How to reset the device?

Answer:

(2) If PPPoE Internet access is needed, you need to check

whether the broadband account and password are ﬁlled in

correctly; otherwise, check whether the Internet status of your

Broadband Gateway is normal.

(3) Make sure the broadband service is normal and you have

paid Internet bill.

(4) When all above are normal, try reboot the device and then

check the network once it powers back on.

should be connected to your Broadband gateway

(i.e. DSL/Cable modem, PON gateway) with a network cable.

Answer:

(on page 1)to view the electronic user manual to switch to the

bridge mode.

What if I already purchased a Mesh Router set

and want to further expand the network with

additional AP(s)?

You need to purchase another or more Azores routers (the same

model) and expand the current mesh network. Please scan the

QR code to view the electronic user manual to obtain the

customized mesh network operation method.

How to manage Azores router network?

Scan QR code to download electronic user manual

One Router Setup Steps

(1) The Single Router or Master AP in a Mesh Router Set can be

connected according to the diagram above. Note the DSL/PON/

Cable Gateway must be connected to the WAN port of the AP. The

AP is connected to the Internet when the LED light is steady Green.

If you can, try place the Single Router or Master AP in an open

area like on a table or a shelf.

(2) Wired devices can be connected directly to LAN port for

Internet access; wireless devices can use the network name

(SSID) & password (see the sticker on the bottom of the Single

Router or Master AP) to connect to Internet.

Note:

For some cable carriers, they limit the number of in-home device

to one. This problem may happen if you replace your old router

with Azores AP. In this case, you need to power down the cable

gateway, leave it powered down for 15 seconds and power back

it up. Afterwards, power down and up the Azores AP or the

Master AP in a mesh set, then you should see the AP’s LED turns

solid green pretty soon.

Answer:

How to access the Slave AP web management

page (GUI) if the mesh pairing failed?

Manually set the PC IP address to 192.168.0.X

(e.g. 192.168.0.100), the subnet mask is 255.255.255.0. Open

the browser and enter http://192.168.0.254

(1) If you know there is a spot in your home, where the Wi-Fi signal is

the weakest. Try place the Slave AP midway between the Master AP

and the weakest spot.

(2) When Master AP and Slave AP paring successfully, the SSID and

Password would be same, that is showing on the bottom of Master AP.

AX1800

WAN

LAN

Powe r

WPS

LED

ON/OFF

AX1800

Connect the Ethernet

interface to WAN Port

1 2 3 4 5

6 7 8 9 10

Technical Support:

Tel: +1 518-300-1595

Email: support@azoresnetworks.com

Connect your device to the Router using wireless or wired

connection. Open an internet browser and enter

http://192.168.0.1(or http://azoresrouter.com). You can modify

WAN conﬁguration, router conﬁguration, single SSID for 2.4

and 5G network, guest Wi-Fi network, and retrieve

your wireless network status.

FCC Warning

This device complies with part 15 of the FCC Rules. Operation is subject to the

following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation.

This equipment generates uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an

uncontrolled environment.

This equipment should be installed and operated with minimum distance 20cm

between the radiator & your body.

Operations in the 5.15-5.25GHz band are restricted to indoor use only.