Azores AX1800 WiFi-6 Wireless Router Manual Azores Networks, LLC
Product Hardware Description Product Backside Description： Reset Button Description Short press (1 second) for reset the router
Long press (5 seconds or longer) for reset to factory default settings LED Description LED Behavior Dark Steady Red Blinking Red Blinking Green Scenario No Power Powering up No network cable connected Network connection in progress Steady Green Function normally and can access the Internet Blinking Blue WPS or Mesh pairing in progress Steady Blue Paring successful Product Manual For single router： Connect the provided network cable from the AX-1800 Router to your home Broadband Gateway (i.e.
For mesh router set: Master AP is used as the main router, which is to be connected, via provided network cable, to your home Broadband Gateway (i.e. cable/DSL modem, PON gateway); Slave AP is used for Wi-Fi network expansion. Please refer to ONE ROUTER SETUP STEPS (for Master AP) & MESH SETUP STEPS (for Slave AP) for network setup.
The Single Router or Master AP in a Mesh Router Set can be connected according to the diagram above. Note the DSL/PON/Cable Gateway must be connected to the WAN port of the AP. The AP is connected to the Internet when the LED light is steady green. If you can, try place the Single Router or Master AP in an open area like on a table or a shelf.
*Note:If you know there is a spot in your home, where the Wi-Fi signal is the weakest. Try place the Slave AP midway between the Master AP and the weakest spot. *Note:When Master AP and Slave AP paring successfully, the SSID and Password would be same, that is showing on the bottom of Master AP. Azores Router APP 01 Connect your Mobile device to Wi-Fi network according to the Wi-Fi SSID and password sticker on the bottom of the Master AP.
04 Enter the “My Wi-Fi” menu to modify WiFi configuration or perform other operations. *Note: If you want to use the mobile device to perform other operations on the router, follow the instructions on the mobile APP.
MORE SETTINGS ※ Refer to the following steps to change the Internet access method: 01 Wireless access terminals (such as mobile phones, PAD, laptops, etc.) or wired access terminals can open the browser to visit http://192.168.0.1(or http://azoresrouter.com), and configure the router device. 02 Password needs to be set for the first time login, click "Next". Please remember this login password. 03 Set Internet configuration.
*Note:If you forget your broadband account password, you can inquire from the broadband operator. *Note:"Skip" defaults to "DHCP" mode. 04 Set Wi-Fi name and password (you can modify the Wi-Fi name). The device selects “The password is the same as the login password” by default, clicks “Next”directly, which means that the default wireless password is the same as the login password; If you do not check "The password is the same as the login password", you can set a new Wi-Fi password and click "Next".
Prompt "Setup Succeed", "Confirm" to jump to the login page. After "Confirm", the wireless terminal can reconnect to the new Wi-Fi name and password. ※ Refer to the following steps to switch Router to Bridge mode: 01 Visit http://192.168.0.1(or http://azoresrouter.com) and using the login password to login. 02 Change the "Uplink mode" to "Bridge Mode" on the "WAN Settings" page and click Save.
03 Start networking. If you choose wired networking, connect the new single product network port to the Master AP LAN port. The wired network is successful when the new single product indicator is steady green; If you choose wireless networking, place the new item near the Master AP, press both device WPS buttons for 1s, then release. The Master AP indicator will turn on in blue for 1 minute, then restore to the original state.
Frequently Asked Questions Q1 After connecting network cable from DSL/PON/Cable gateway to the Azores AP or Azores Master AP in a mesh set, the AP's red LED is keep flashing.What should I do? Answer:For some cable carriers limit the number of in-home device to one. This problem may happen if you replace your old router with Azores AP. In this case, you need to power down the cable gateway, leave it powered down for 15 seconds and power back it up.
