User's Manual

SIDEWINDER PG. 9
PG. 4 SIDEWINDER
down side by the centering ring indentation.
This practice will increase the pad life and help
maintain a properly functioning pad driver.
NEVER TILT A MACHINE ON ITS SIDE!
II. OPERATION
This machine is designed to deep scrub and/or
strip hard surface floors in preparation for top
coat or restoring of tile, smooth concrete,
terrazzo or close fitted tile. Any other
application of the equipment should be checked
with customer service at the factory to
determine if the proposed use is appropriate.
Provide and use ear protection during
operation.
Never let an untrained person operate or
perform repairs on the machine. They may
hurt themselves, damage the floor or the
equipment.
Engine speed not to exceed 3400 RPM.
This machine is not suitable for picking up
hazardous dust.
Do not use on surfaces with a gradient
exceeding 2%.
A. Prepare the machine for operation.
Follow steps A through E in the previous
section and determine the best brush or pad for
the task.
B. Transport by tilting on rear wheels.
C. Apply cleaning or stripping solution to the
floor.
III. STARTING THE ENGINE
A. Kawasaki with centrifugal clutch:
1. Open propane (LPG) tank valve
(counter clockwise).
2. Turn the key to start position and move
throttle towards fast position.
3. If engine does not start, release the key,
then try again.
4. Equipment is supplied with a centrifugal
clutch. When engine RPM is lower than
1800 RPM clutch will disengage;
brushes/pads will stop.
B. Never tilt back machine while engine is
running.
IV. STOPPING THE ENGINE
Turn the propane tank valve clockwise to a
closed position and turn the key OFF.
NOTE: The exhaust system will be very hot and
takes several minutes to cool, so keep yourself
and all materials clear.
V. OPERATING PROCEDURES
A. Transporting the machine
1. The tank should be securely fastened.
2. The tank valve must be closed.
B. Cleaning the equipment
1. Place machine in “tilt back” position.
2. Rinse unit between top of brushes and
brush plate. Do not spray water into brush
drive (above plate).
3. Rinse around splash skirt and body.
4. Return machine to operating position, then
start engine and run machine briefly to
expel any excess water.
C. Storing the machine and tank
1. The engine should be stopped properly
and the tank valve closed.
2. Remove the LPG tank from the machine
and store the tank in a well ventilated
approved area.
3. Store your machine in a safe area: away
from enclosed high heat, away from sparks
or flames, away from traffic lanes of
heavy equipment.
VI. MAINTENANCE
A. Machine & engine maintenance
1. Refer to engine manufacturer’s owners
manual and comply completely with the
instructions. Change the oil and filter
according to the Engine Owners Manual.
2. Keep a good service log on each
machine with the date, hour meter
reading, type(s) of service performed
and the name of the person who
performed them.
3. Clean the entire unit after each use. when
cleaning the unit, check for possible
loose nuts and bolts.
B. Engine maintenance meter
This multi-function meter acts as a preventive
maintenance tool, which benefits you with
increased fuel economy, less down-time and longer
engine life.
The meter’s displays are:
Hour Meter: Displays total run hours when
machine is off.
Tachometer: Indicates engine RPM during operation.
Service Alert: The display flashes to alert you to
SIDEWINDER 24" BODY PARTS
PART # DESCRIPTION PART # QTY
1 TOGGLE & NUT 284-TB2-60 1
2 3/8-16 LOK-NUT 164-22834 5
3 LEFT BRACKET 283-025-400 1
RIGHT BRACKET 283-025-500 1
4 T-HANDLE 283-025-600 1
5 HANDLE GRIP 224-1 2
6 LOK-PIN 625-98404A385 1
7 KICK PLATE 283-010-04 1
8 3/8-16*3 BOLT 164-10131 1
9 20 # LP CYLINDER 293-20#STLMF 1
10 HANLE ASSEMBLY 010-971CCH 1
11 6" WHEEL 156-XA-06251-12 2
12 SPANNER BUSHING 156-ZF-0812-39 2
13 AXEL & NUT 156-ALBZJ085408 2
14 BODY 288-01024S-01 1
15 BRUSHDRIVE COVER 283-01024-02 1
16 SPLASH SKIRT 01024S-971S 1
17 BELT COVER 283-01024-03 1
18 THROTTLE CABLE 196-60314 1
SIDEWINDER 24"
PART # DESCRIPTION PART # QTY
1 3/8-16 HEX NUT 164-22004 2
2 TENSION PULLEY 188-V42B 1
3 BELT TENSIONER 010-962T 1
4 BELT 113-L538 1
5 5/16 FLAT WASHER 164-20156 1
6 NYLON BUSHING 196-71200 2
7 TENSION SPRING 173-7599-DWG 1
SIDEWINDER 24" LOWER DRIVE
PART # DESCRIPTION PART # QTY
1 HEAD SUPPORT BOOM 01024-962B 1
2 INPUT BOOM PULLEY 0105-962S1 1
3 5/16 FLAT WASHER 164-20156 3
4 3/8-16*2 BOLT 164-10123 2
5 24" TOP PAN 01024-962MS 1
6 BELLEVILLE WASHER 164-20250 8
7 OUTER PAN PULLEY 010-962S3 3
8 BELT 113-BB68 1
9 BELT TENSIONER 01024-962TT 1
10 BRUSH OPTIONS
HVY DUTY STRIP (RED) 01024-962STBH 3
HEAVY SCRUB (BLUE) 01024-962SCB 3
PAD HOLDER 01024-962STP 3
11 24" STEEL PLATE 01024-962MP 1
12 TENSION SPRING 173-7501-DWG 1
13 NYLON BUSHING 198-71200 1
14 3/8-16 HEX NUT 164-22004 2
15 TENSION PULLEY 188-V42B 1
16 CENTER PAN PULLEY 010-962S2 1
17 BOOM PULLEY WASHER 164-58114F 1
18 BRUSH DRIVE UNIT 01024-953B 1
T
TT