Aztech DSL5018EN 4-Port ADSL 2/2+ 150 MbpsWireless-N Modem Router V1.
© COPYRIGHT 2013 ALL RIGHTS RESERVED No part of this document may be reproduced, republished, or retransmitted in any form or by any means whatsoever, whether electronically or mechanically, including, but not limited to, by way of photocopying, recording, information recording, or through retrieval systems without the express written permission. We reserve the right to revise this document at any time without the obligation to notify any person and/or entity.
CONTENTS About the Device ............................................................................................................ 1 Minimum System Requirements .................................................................................. 1 Package Contents .......................................................................................................... 1 Device Design ................................................................................................................
Application> ACL ................................................................................................................................... 25 Application> Filter ................................................................................................................................. 26 Application> Routing ............................................................................................................................. 27 Application> NAT.........................................
U s e r M a n u a l 1 About the Device The Aztech DSL5018EN 4-Port ADSL2+ 150Mbps Wireless-N Modem Router with USB host uses complete Ralink chipsets solution that fully complies with ADSL2/ADSL2+ standard. The Aztech DSL5018EN supports 1T1R MIMO technology with PHY rate up to 150Mbps.
U s e r M a n u a l 2 Device Design Front Panel LABEL ICON ACTION DESCRIPTION 1. POWER Off Steady green Steady red No power is supplied to the device Connected to an AC power supply Error on the device 2. ETHERNET LAN Off Steady green Blinking green No Ethernet connection Connected to an Ethernet port Transmitting/Receiving data 3. WIRELESS Off Steady green Blinking green Wireless interface disabled Wireless Interface enabled Transmitting/Receiving data 4.
U s e r M a n u a l 3 Back Panel LABEL DESCRIPTION 1. 12VDC 12V 1.0A DC Input port 2. ON/OFF Power ON/OFF button 3. ETHERNET Connecting computers and other Ethernet devices (RJ45) 4. USB Connecting USB storage or printer 5. DSL Connecting the modem to an ADSL line (RJ11) 6. WPS To setup wireless security with WPS-capable clients 7. ANTENNA Fixed Wifi Antenna 8.
U s e r M a n u a l 4 Getting Started Setting up the device is easy. The flowchart below provides an outline of the steps needed to complete the installation. Brief descriptions appear beside each step. Detailed instructions are provided in the subsequent pages. Plan your Network Remove/Disable Conflicts You may need to check some settings or disable some applications before installation. Set up the Router Connect the telephone cables, Ethernet cables, and power adapter.
U s e r M a n u a l 5 Planning Your Network Before moving ahead to setup your network, it is a good idea to draw out a network diagram to help identify your network devices and plan out how to connect these devices. The illustration below is an example of a network diagram. Each port in the router can be used for different connections.
U s e r M a n u a l 6 Remove or Disable Conflicts To ensure that the router installation moves on smoothly, you need to remove or disable conflicts that may interfere with the installation.
U s e r M a n u a l 7 Configuring Internet Properties To set the Internet Properties: 1. 2. 3. 4. 5. Select Start > Run. This opens the Run dialog box. Enter control inetcpl.cpl and then click OK. This opens Internet Properties. Click Connections tab. In the Dial-up and Virtual Private Network settings pane, select ‘Never dial a connection’. Click OK to close Internet Properties. Removing Temporary Internet Files Temporary Internet files are files from Web sites that are stored in your computer.
U s e r M a n u a l 8 To setup a telephone on the POTS Splitter (DSL Microfilter): a. b. c. 4. 5. Locate the phone jack in your house. Insert the POTS Splitter into the phone jack. Plug one end of the telephone cable from the POTS Splitter’s TEL port and then plug the other end into the telephone. Connect the power adapter from the router’s 12V 1.0A DC port into the power outlet. Press the ON/OFF switch to turn on the device.
U s e r M a n u a l 9 Connecting to the Internet You can use the web user interface to setup your Internet connection. Connecting using Quick Setup 1. 2. 3. Launch the web browser. Input 192.168.1.1 on the address bar and press enter. Input ‘admin’ for username and ‘admin’ for password. Click the Login button. 4. Click Quick Setup on the Basic menu.
U s e r 5. M a n u a l 10 Under WAN Connection a. Select Connection Type b. Input VPI and VCI on the required field. (Note: Please refer to your Internet Service Provider for the information needed on the required field). 6. Under Wireless a. Tick WLAN Enabled box to enable the wireless interface. b. Tick Broadcast SSID to broadcast Wireless Name. c. SSID input the Wireless Name on the required field. d. Tick WPA/WPA2 Enabled to enable the wireless security e.
U s e r M a n u a l 11 Basic Mode Basic Mode displays pages with information about the device and its current configuration. Basic – Home This section of the web user interface displays information about of the Internet, LAN, Wireless Connection, Local Network, Storage and Printer status. Internet Connection. Provides details of the Internet connection. LAN Connection. Provides details of Local Area Network connection. Wireless Connection. Provides an overview of the Wireless connection information.
U s e r M a n u a l 12 Basic -Wizard This section of the web user interface guides user to setup their device to access the Internet and set wireless connection.
U s e r M a n u a l 13 Basic – Quick Setup This section of the web user interface displays allows user to configure Time and Date WAN and Wireless connection. WAN Connection. Allows user to set the WAN connection type. 1. Connection Type. Allows you to change the default Internet Connection type. Verify with your Internet Service Provider your Internet Connection Type before changing the configuration. 2. VPI/VCI. Allows you to change the default VPI/VCI set on the modem.
U s e r M a n u a l 14 Advanced Mode The Advanced Mode page can be accessed from the Basic page by clicking on Advanced Mode. Advanced Mode – Network The initial page will show all the settings of your existing WAN connection configured on the router. Network>Internet This page allows user to configure the default WAN settings of the modem/router.
U s e r M a n u a l 15
U s e r M a n u a l To add a WAN interface: 1. Select an available Virtual Circuit from the drop-down box 2. Enter VPI/VCI settings (provided by your ISP) 3. Input QoS settings (provided by your ISP) 4. Select the IPv4/IPv6 version 5. Select the WAN Connection Type 6. For PPP enter PPP Username and Password (provided by your ISP) 7. Bridge Interface should be deactivated. 8. Connection Setting should be ‘Always on’. 9. Ensure Default Route is selected as Yes 10. Ensure Get IP Address is set to Dynamic 11.
U s e r M a n u a l 17 Network>LAN Configure the DSL Router IP Address and Subnet Mask for LAN interface. You may also configure the DHCP server and Public IP Pass Through settings of your router. This page also displays the DHCP Client list connected to the modem/router.
U s e r M a n u a l 18 Network>DHCP Reservation Allows you to reserve an IP address for a specific device connected to the modem/router. Network> Ethernet Media Type Allows you to change the speed at which the Ethernet Ports should operate on. Click Apply for the settings to take effect.
U s e r M a n u a l 19 Network> ADSL Allows you to select the ADSL Mode and Type required by their Internet Service Provider. Network> SNMP Allows you to configure SNMP settings, type the SNMP information on the required field and click Apply for the settings to take effect.
U s e r M a n u a l 20 Network> CWMP Allows the Internet Service Provider to manage the device via remotely. Input the information on the required field and click apply for the settings to take effect. Network> IPv6RD Allows Internet service Provider to configure IPv6 settings. Input the information on the required field and click Apply for the settings to take effect.
U s e r M a n u a l 21 Advanced – Wireless This page allows user to change the default configuration of the Wireless LAN connection set on the modem.
U s e r M a n u a l 22 Wireless> Basic Allows you to change the default Wireless Configuration set on the device. Access Point settings allows you to Enable or Disable the wireless interface. 11.n settings allows you to change the wireless channel bandwidth. SSID settings allows user to change or keep Wireless name that is being broadcasted by the device. Click Apply for the settings to take effect.
U s e r M a n u a l 23 Wireless> Security This page allows you to change the default Wireless Security set on the modem. This also allows you to enable/disable the WPS feature, click Apply for the settings to take effect.
U s e r M a n u a l 24 Wireless> MAC Address Filter This page allows you to control which wireless clients will be Allowed or Denied access connection to the modem by entering the MAC address of the wireless client to the Access control list. Click Apply for the settings to take effect. Advanced – Applications Allows you to change/set the modem’s application features.
U s e r M a n u a l 25 Application > DDNS This page allows you to set a static host name with a Dynamic IP address. Input the information on the required box click Save for the settings to take effect. Application> ACL This feature allows you to configure access rights to a certain core services running on your modem. You can allow or deny access from LAN or WAN connection to meet your security requirements. Tick the boxes you wish to enable and click Save for the settings to take effect.
U s e r M a n u a l 26 Application> Filter This page allows you to set the IP, MAC, URL and Application filtering on the device. Select Filter type from the drop down box and input the information on the required field click Set for the settings to take effect.
U s e r M a n u a l 27 Application> Routing This page will list the routing table information. This allows you to Add/Edit/Drop the static route. Click Add Route and input the information on the required field then click Apply for the settings to take effect.
U s e r M a n u a l 28 Application> NAT Allows user to configure DMZ, Port Forwarding and Port Triggering applications. DMZ. This feature allows you to set a host between a private local network and the public network. This feature allows outside users from getting direct access to your local network. Port Forwarding. This feature allows you to set a direct incoming traffic from the Internet to a specific computer in your local network. Port Triggering.
U s e r M a n u a l 29 Application> QoS Quality of Service or QoS provides different priority to different applications, users, or data flows, to guarantee a certain level of performance. For example, QoS is important for realtime streaming multimedia applications such as voice over IP, online games and IPTV to provide fixed bit rate and prevent delay.
U s e r M a n u a l 30 Application> Port Mapping This page feature allows ATM PVCs to be permanently routed to a physical interface on the device.
U s e r M a n u a l 31 Application> Parental This page allows you to block access to specific URL or MAC address on a specific day and time. Select Activated and Blocking Type then input the information on the required field and click Apply for the settings to take effect. 1. 2. 3. Day of Week- tick the days that you want to block the access to a specific URL or MAC Address. Start Blocking Time- Input the start time on the required field.
U s e r M a n u a l Application> Firewall This page allows you to enable or disable Firewall and SPI feature set on the modem. Advanced- System Allows you to Back-up, Restore settings and do Firmware upgrade on the modem.
U s e r M a n u a l 33 System>Information Displays detailed information of the modem’s Firmware version, LAN/WLAN MAC Address and System Uptime. System> Time Zone Allows you to set the time used by the device for scheduling services.
U s e r M a n u a l 34 System> UPnP Allows you to enable/disable UPnP application set on the modem. System> Settings Allows you to Save and Restore modem’s configuration. 1. Back-up. Click Backup button to save romfile.cfg on your computer. This will serve as your modem’s back-up configuration file. 2. Restore. click ‘Browse’ to select romfile.cfg that was saved on your computer to restore your modem to the last saved configuration then click Restore for the settings to take effect. 3.
U s e r M a n u a l 35 System> Firmware Allows you to change the firmware saved on the modem. System> Password This page allows you to change the password set on the modem to access the Web User Interface.
U s e r M a n u a l Advanced – Status Displays the status of the modem. Status> Statistic Provides statistical information of LAN, ADSL and WLAN interface.
U s e r M a n u a l Status> ADSL Status Displays detailed information of the ADSL quality. Status> System Log Displays the modem’s system log.
U s e r M a n u a l 38 Status> Diagnostics Displays the test results for the connectivity of the physical later and protocol for ADSL, ATM, WLAN/LAN port and LAN connection, click Start test to start the test. Status> Network Tools Allows you to test the modem’s Internet connectivity.
U s e r M a n u a l 39 Modem Care Tips 1. Do not deface the modem. 2. Do not use any power adapters with the modem other than the supplied adapter as it may damage the device rendering it unusable. 3. Do not let the modem get wet, when water gets in contact with the modem, the internal components can corrode which breaks down the modem. 4. Install the modem on a flat surface and ensure that there is enough space for air to circulate. 5.
