AW-CM286NF IEEE 802.11 1X1 ac/a/b/g/n Wireless LAN + Bluetooth NGFF Module Datasheet Version 0.8 (For Cert.
1. General Description 1-1. Product Overview and Functional Description AzureWave Technologies, Inc. introduces the IEEE 802.11ac/a/b/g/n 1X1 WLAN & Bluetooth NGFF module --- AW-CM286NF. The module is targeted to mobile devices including Notebook, TV, Tablet and Gaming Device which need small package module, low power consumption, multiple interfaces and OS support.
1-2. Key feature: Small footprint: 16mm(L) x 12mm(W) x 1.95mm(H)Max IEEE 802.11ac compliant, 1x1 spatial stream with data rates up to MCS9 (433 Mbps) Bluetooth 4.2 (supports Low Energy (LE)) SDIO 3.
1-3. Specifications Table Model Name AW-CM286NF Product Description Wireless LAN + Bluetooth Combo Module WLAN Standard IEEE 802.11ac/a/b/g/n, Wi-Fi compliant Bluetooth Standard Bluetooth 4.2 complaint with Bluetooth 2.1+Enhanced Data Rate (EDR) Host Interface Major Chipset Marvell 88W8887 Dimension 12mm x 16mm x 1.95mm(Max) Weight TBD Package LGA SDIO 3.0 device interface (SPI, 1-bit SDIO, 4-bit SDIO transfer modes at full clock range up to 208 MHz) Operating Conditions Voltage 3.
Receive Sensitivity WLAN: WLAN G band : 11b:-87dBm (11M) 11g:-73dBm (54M) 11n:HT20 -70dBm (MCS7) HT40 -68dBm (MCS7) WLAN A band: 11a: -68dBm (54M) 11n HT20:-66dBm (MCS7) 11n HT40:-64dBm(MCS7) 11ac VHT_20: -61dBm(MCS8) 11ac VHT_40: -58dBm(MCS9) 11ac VHT_80: -52dBm(MCS9) Bluetooth: BDR:-88dBm(DH1) EDR:-91dBm(2DH5) BLE:-94.5dBm Data Rates WLAN 802.11b: 1, 2, 5.5, 11Mbps 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54Mbps 802.11n: up to 150Mbps 802.11ac:up to 86.7Mbps (20MHz channel) 802.
2. Electrical Characteristic 2-1.Absolute Maximum Ratings Symbol VDD_3V3 VIO VIO_SD Parameter 3.3V input Host I/O power supply SDIO power supply Condition Min Typ Max Units -- -- 3.3 4.0 V 3.3 4.0 2.5 3.0 1.8 2.2 3.3 4.0 1.8 2.2 -- -- -- -- V V 2-2.Recommanded Operating Conditions Symbol VBAT_IN VIO VIO_SD Parameter LDO VBAT input Condition Min Typ Max Units -- 2.7 3.3 3.63 V 2.97 3.3 3.63 2.25 2.5 2.75 1.62 1.8 1.98 2.97 3.3 3.63 1.62 1.8 1.98 1.
2-3.Clock Specifications 2-3-1 External Sleep Clock Timing External Sleep Clock is necessary for two reasons: 1. Auto frequency Detection. This is where the internal logic will bin the Ref clock source to figure out what is the reference clock frequency is. This is done so no strapping is needed for telling 8887 what the ref clock input is. 2. Allow low current modes for BT to enter sleep modes such as sniff modes. The AW-CM286NF external sleep clock pin is powered from the 1.8V voltage supply.
2-5.
3. Host Interfaces 3-1. SDIO Interface The AW-CM286NF supports a SDIO device interface that conforms to the industry standard SDIO Full-Speed card specification and allows a host controller using the SDIO bus protocol to access the Wireless module device. The AW-CM286NF acts as the device on the SDIO bus. The host unit can access registers of the SDIO interface directly and can access shared memory in the device through the use of BARs and a DMA engine.
3-1-2. Default Speed, High Speed Modes (3.3V) SDIO Protocol Timing Diagram – Default Speed Mode (3.3V) SDIO Protocol Timing Diagram – HighSpeed Mode (3.3V) Table shows SDIO Timing Data—Default Speed, High Speed Modes (3.3V) NOTE: Over full range of values specified in the Recommended Operating Conditions unless otherwise specified.
3-2. PCM Interface 3-2-1.
3-2-2.
4. Pin Definition Pin No Definition Basic Description Type 1 GPIO[15]/TMS JTAG controller select 2 GPIO[14]/TCK JTAG test clock 3 GPIO[16]/TDI JTAG test data(input) I 4 VDD_3V3 3.3V Analog RF Power Supply I 5 VDD_3V3 3.
Pin No Definition Basic Description Type 28 GPIO[13] 29 NC No connect -- 30 NC No connect -- 31 GPIO[12] GPIO[12] -- 32 GND 33 NC No connect -- 34 NC No connect -- 35 GND 36 NC No connect -- 37 NC No connect -- 38 GND 39 NC No connect -- 40 NC No connect -- 41 GND 42 GPIO[0]/CLK_REQ 43 NC 44 VIO_SD 45 GPIO[13] System Ground Pin System Ground Pin System Ground Pin System Ground Pin GPIO[0] (input/output) O No connect -- 1.8V/3.
Pin No Definition Basic Description Type 59 GPIO[4]/PCM_IN GPIO[4] (input/output) I 60 GPIO[5]/PCM_OUT GPIO[5] (input/output) O 61 GPIO[6]/PCM_CLK GPIO[6] (input/output) I/O 62 GND 63 NC 64 GPIO[2]/WLAN_LED 65 GPIO[3]/BT_LED 66 System Ground Pin No connect -- LED_OUT_WLAN (output) O LED_OUT_BT (output) O NC No connect -- 67 NC No connect -- 68 GND 69 NC No connect -- 70 NC No connect -- 71 GND 72 NC No connect -- 73 VIO Digital I/O Power Supply I 74
Pin No Definition Basic Description 90 GND System Ground Pin 91 GND System Ground Pin 92 GND System Ground Pin 93 GND System Ground Pin 94 GND System Ground Pin 95 GND System Ground Pin 96 GND System Ground Pin G1 GND System Ground Pin G2 GND System Ground Pin G3 GND System Ground Pin G4 GND System Ground Pin G5 GND System Ground Pin G6 GND System Ground Pin G7 GND System Ground Pin G8 GND System Ground Pin G9 GND System Ground Pin G10 GND System Ground P
5. Mechanical Information 5-1.
5-2.
6.
6-4 生产标签 AFFIX PACKING LABEL 6-5 1 Carton= 5 Boxes TRANSPARENT SEALING TAPE AFFIX PACKING LABEL 6-6 Note: 1 tape reel = 1 box = 1,500pcs 1 carton = 5 boxes = 5 * 1,500pcs=7,500pcs - 20 -
FCC Statement: FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
If the labelling area is larger than the palm of the hand, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Ant. 1 2 3 4 5 6 Ant. Brand Holder Brand Holder P/N SE-ECX10-001 Smart Approach Co.,Ltd.
IC Statement: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 54705600 MHz and 5650-5725 MHz. Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 54705600 MHz et 5650-5725 MHz. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC Statement: FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
If the labelling area is larger than the palm of the hand, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. Ant. Brand Holder Brand Holder P/N Antenna Type Connector 1 Smart Approach Co.,Ltd.
IC Statement: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
Dynamic Frequency Selection (DFS) for devices operating in the bands 5250- 5350 MHz, 5470-5600 MHz and 5650-5725 MHz. Sélection dynamique de fréquences (DFS) pour les dispositifs fonctionnant dans les bandes 5250-5350 MHz, 5470-5600 MHz et 5650-5725 MHz. The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.
USERS MANUAL OF THE END PRODUCT: In the users manual of the end product, the end user has to be informed to keep at least 20 cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment.
