AW-NM387 IEEE 802.11 b/g/n Wireless LAN & Bluetooth Module Datasheet Version 0.4 Document release Version0.1 Version0.12 Version0.2 Version0.3 Version0.
1. General Description 1-1. Product Overview and Functional Description AzureWave Technologies, Inc. introduces the first IEEE 802.11b/g/n WLAN & Bluetooth module IC--AW-NM387. The module is targeted to mobile devices including Personal Digital Assistants (PDAs), Netbook, Tablet and Gaming Devices which need small package module, low power consumption, multiple interfaces and OS support.
1-2. Key Features Small footprint: 23mm(L) x 11mm(W) x 2.4 mm(H) SDIO interfaces support for WLAN SDIO for Bluetooth Bluetooth 3.0 + High Speed (HS) also complaint with Bluetooth 2.1 + Enhanced Data Rate (EDR) Cellular phone co-existence support Multiple power saving modes for low power consumption IEEE 802.11i for advanced security Quality of Service (QoS) support for multimedia applications Drip-in WLAN Linux drivers are Android ready and validated on Android based systems.
2. Block Diagram 3. Specifications Table Wireless LAN &Bluetooth Module IEEE 802.11b/g/n, Wi-Fi compliant Bluetooth 3.0 +high speed complaint with Bluetooth 2.1+Enhanced Data Rate (EDR) WLAN and Bluetooth through SDIO Marvell 8787 11mm x 23mm x 2.4mm ! " ! 3.3V/1.
802.11b(Ch1~13): typical 17dBm +/- 2dBm 802.11b(Ch14): typical 10dBm +/- 2dBm 802.11g: typical 14dBm +/- 2dBm 802.11n: typical HT20 13dBm +/- 2dBm HT40 12dBm +/- 2dBm Typical power: Bluetooth Bluetooth Class 1.5>1dBm WLAN&BT through U.FL connector ( WLAN: 802.11b: Minimum -86dBm at 11Mbps 802.11g: Minimum -71dBm at 54Mbps 802.
2. Electrical Characteristics 2-1. Absolute Maximum Ratings Symbol 3.3V VIO Parameter Condition Min Typ Max Units 3.3 4.6 V 1.8 2.3 2.6 3.1 3.3 4.2 1.8 2.3 V Min Typ Max Units 3 3.3 3.6 V 1.62 1.8 1.98 2.5 2.6 2.7 2.97 3.3 3.63 1.7 1.8 1.9 PA and Internal voltage power supply Host I/O power supply External Analog I/O power 1.8V supply(optional) V 2-2. Recommended Operating Conditions Symbol 3.3V VIO External 1.
The AW-NM387 external sleep clock pin is powered from the 1.8V voltage supply. Symbol CLK THIGH TLOW TRISE TFALL Parameter Clock Frequency Range Clock high time Clock low time Clock rise time Clock fall time Min 32 or 32.768 -50ppm 40 40 --- 2-4. SDIO Host Interface Specifications Referred from Marvell hardware specifications SDIO Protocol Timing Diagram SDIO Protocol Timing Diagram—High Speed Mode -7- Typical 32 or 32.768 ----- Max 32 or 32.
SDIO Timing Data Symbol Parameter fpp CLK Frequency TWH CLK High Time TWL CLK Low Time TISU Input Setup Time TIH Input Hold Time TODLY Output Delay Time TOH Output Hold Time Condition Min Normal 0 25 High Speed 0 75 Normal 10 High Speed 7 Normal 10 High Speed 7 Normal 5 High Speed 6 Normal 5 High Speed 2 0 High Speed 2-5. Pin Out Power Supply Use VIO PDn SD_CLK SD_CMD SD_DAT[1] SD_DAT[2] SD_DAT[3] WiFi_LED BT_LED -8- 2.5 Typ Max Units MHz ns 7.
3. Pin Definition Pin Assignment Pin No Definition 1 GND 2 External 1.8V(optional) 3 PDn 4 VIO 5 SLEEP_CLK 6 GND 7 8 9 10 11 SD_CMD SD_DAT[0] SD_DAT[1] SD_DAT[2] SD_CLK Basic Description 1.8V voltage optional. Default model is used internal 1.8V, so please keep this pin float. If the customer wants to use external 1.8V model. Please contact to AzureWave.
4.
5. Mechanical Characteristic 5.1 Outline 11X23mm Pin1 5.
No of Contacts 17 B 4.2mm C 4.8mm 5.3 Connector Insertion Depth of FPC - 12 - F 5.
5.
FCC Notice : Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. As long as 3 conditions above are met, further transmitter test will not be required.
Industry Canada statement: This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence.
regarding to Regulatory Domain change. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada.
========================================================= IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization.
être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient des IC: 6100A-NM387".
