HSPA+ Mobile Router User Manual V1.
Table of Contents 1. Introduction ...................................................................................................................... 4 1.1 Features ..................................................................................................................................4 1.2 General Specifications ............................................................................................................5 1.3 Product Overview ......................................................
.6.3. Sent .............................................................................................................................. 18 3.6.4. Draft............................................................................................................................. 18 3.7 System................................................................................................................................ 19 3.7.1. Administrator ..................................................................
1. Introduction HSPA+ Mobile Router is a highly integrated wireless solution for 3G and Wi-Fi. It provides HSPA+ downlink data rate up to 21 Mbps, uplink data rate up to 5.76 Mbps and 3G mobile broadband wherever you are. With HSPA+ Mobile Router, you don’t have to worry about the availability of Internet access as long as 3G network is available. It provides connection with 1 PC USB host (via Ethernet) and at the same time connect up to 6 Wi-Fi enabled devices such as smart phones, laptops, or tablet PCs.
1.2 General Specifications Model Name Technical Standard External Interfaces HSPA+ Mobile Router 3GPP Release 7 compliant GSM/GPRS/EDGE 3GPP Release 99 compliant Micro USB interface: supporting USB 2.0 high speed Standard 6-pin SIM card interface Operating Conditions Voltage Temperature USB 5V Operating：-10℃ to +45℃ Storage：-20℃ to +70℃ Dimension 90mm x 50mm x 12mm Form Factor Bar type mobile router Battery capacity 3.
1.3 Product Overview 1.3.1 Appearance LED Power button Reset LED indicator: Indicator Blinking (Fast) Color Solid Green New incoming message Purple HSPA+ network transmitting Blue WCDMA/HSDPA/ HSUPA network transmitting Green GSM/GPRS network transmitting Red 1. SIM error 2.
Indicator Battery Battery Battery Wi-Fi Blinking (Fast) Color Solid Blue Fully charged Green Battery is 50% to 99% charged Red Battery is 0% to 50% charged Less than 3% capacity, without charge Green Wi-Fi active transmitting Blinking (Slow) 100% to 50% capacity, without charge 50% to 10% capacity, without charge Less than 10% capacity, without charge Solid: LED stays on Blinking (Fast): LED will blink every 0.
1.3.3 FCC Regulations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
The highest SAR value for the device as reported to the FCC, as described in User’s guide is 1.39 W/kg. While there may be differences between the SAR levels of various devices and at various positions, they all meet the government requirement. The FCC has granted an Equipment Authorization for this device with all reported SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR information on this device is on file with the FCC and can be found under the Display Grant section of www.
2. HSPA+ Mobile Router Connection With HSPA+ MOBILE ROUTER, no installation of driver is required. All you need to do is plug-andplay and 6 Wifi-enabled devices can be connected simultaneously. 2.1 Install HSPA+ Mobile Router for Ethernet connection After connecting HSPA+ MOBILE ROUTER by USB, please refer installing steps below. 1. Open battery cover and take out battery to insert SIM card. 2. Put in the battery. to turn on the device. 3. Push 4. Double click “Computer” 5.
3. Connection Manager HSPA+ MOBILE ROUTER provides a connection manager for users to manage mobile broadband connections. Through the connection manager you can manage and adjust settings for your device. Please follow the steps below to enter the webpage of you connection manager. 1. Firstly, turn the power on and connect to HSPA+ MOBILE ROUTER. 2. Open browser and enter http://192.168.1.1. 3. The default user name and password are both admin. Enter “admin” in Name and Password field. 4. Click “Log In”.
3.2 Information 3.2.1. Status After logging onto the connection manager webpage, the status page will show. This is what the default page will look like for your new HSPA+ MOBILE ROUTER device. Refresh: Refresh the status page. Connect: Press "Connect" button to connect to the 3G network. Disconnect: Press "Disconnect" button to disconnect from the 3G network. 3.2.2. Usages Clear History：Reset total connected time and total upload/download data. Refresh: Refresh the statistics page.
3.2.3. Wi-Fi User List This displays the MAC address of associated devices connected to the HSPA+ MOBILE ROUTER. 3.2.4. History This displays the connections information of associated devices connected to the HSPA+ MOBILE ROUTER. 3.3 3G Settings 3.3.1. Profile Auto APN: This is enabled by default. APN will be detected automatically when connected to the 3G network. Profile Name, Name, Password, and APN: Please enter the information provided by your Internet Service Provider if "Auto APN" is disabled.
Manual: You have to go to "Status-> Status" in this web setting page and click the "Connect" button manually to bring up the 3G connection. Maximum Idle Time: On the "On demand" or "Manual" reconnection mode, the 3G connection will disconnect if you do not use the internet within this setting time. 3.3.2. Network Settings Select Operator Automatic (default): This chooses a 3G network automatically. Manual: You need to choose the 3G network manually from the “Operator List” below.
Enable: Enable the PIN Code. You need to enter correct SIM card PIN code to open 3G network. Set PIN Code: When PIN is enabled, you can change the PIN Code from current PIN Code to New PIN Code and confirm it in HSPA+ Mobile Router. 3.4 Wi-Fi Settings 3.4.1. Basic WLAN: Enabled (default): This turns on the Wi-Fi connection, and becomes a router sharing the 3G connection. Disabled: This turns off the Wi-Fi connection and becomes modem mode allowing only one device to internet connection by USB.
3.4.2. Advanced Broadcast SSID: It is enabled by default, and anyone can see this device in the wireless network. If it is disabled, any network client who wants to connect to this device has to enter the correct SSID. Power Save: This function only works on no charging mode. If no any Wireless station connect to Router and idle time is up, the Wi-Fi will be turn off. At this time, user must press power button 1 second, and then the Wireless interface will be wake up again.
3.5 DHCP Device IP: The IP address of the HSPA+ MOBILE ROUTER for the administrator to log on the web setting page. Subnet Mask: The subnet mask of this device is 255.255.255.0. DHCP Server: The HSPA+ Mobile Router could be used as a DHCP server and assign IP address to the network client in your wireless network. The default is “Enabled”. Address Range: Specify the range of IP address that DHCP server can assign to the network client. 3.6 Message 3.6.1.
3.6.2. Inbox Store every received message. Device & SimCard：Total number of received messages/Maximum stored number. Delete Selected：Delete messages selected. Delete All：Delete all messages in the inbox. Read and reply messages selected. 3.6.3. Sent Stores every sent message. Delete Selected：Delete messages selected. Delete All：Delete all messages in the inbox. Sent and Draft Messages: Total number of messages sent and saved in draft / Maximum capacity of messages. 3.6.
Store the draft. You can continue to edit the message afterwards Delete Selected：Delete messages selected. Delete All：Delete all messages in the inbox. Sent and Draft Messages: Total number of messages sent and draft saved / Maximum capacity of stored messages. 3.7 System 3.7.1. Administrator Login Name: Using "admin" account log in this web page for network and wireless settings. New Password: The default password is "admin".
3.7.3. Firmware Upgrade Every device can update firmware version of HSPA+ MOBILE ROUTER by webpage. Browse file of the latest firmware which in every device, and then click “Update” to update. 3.7.4. Language Default Language: You can select the default language for web setting page in this drop-down menu.
4. Troubleshooting 1. Why can’t I access the web setting page? Ans: 1. Please check if the LED is illuminating, otherwise you may need to unplug the HSPA+ MOBILE ROUTER and insert once again. 2. Please make sure if your device has connected to the SSID via Wi-Fi. 3. The default IP address is 192.168.1.1, please make sure you have typed it correctly in your web browser. 2. How to restore to default router settings? Ans: 1.
4. Go to the page “Wi-Fi Settings -> Advanced” and make sure you have selected the “Enabled” option in “Broadcast SSID”. 5. What should I do if my SIM card is locked and I can’t connect to the mobile network? Ans: Please contact your service provider for further assistance.
