INSTALLATION MANUAL B-BAND A5T SIDEMOUNT PREAMP WITH B-BAND UST OR AST TRANSDUCER This is a basic installation manual and tip sheet. For more information, technical support, and pictures of installations about all B-Band products please check the B-Band website at www.b-band.com or contact your B-Band dealer, distributor or B-Band directly.
DEAR CUSTOMER, Thank you very much for purchasing this state-of-the-art B-Band® acoustic transducer system. B-Band takes care to provide the highest quality product and is manufactured and supported in true spirit of acoustic instrument aficionados. The outstanding sound reproduction of B-Band transducers is based on the technology of a very special, worldwide-patented material that is exclusive to B-Band. This material is very different from, and has nothing to do with, piezo-electric films or transducers.
by a professional qualified guitar craftsman or technician. Some installations require a high knowledge about woodworking and guitar structure. When doing any drilling, sawing, cutting or routing at the guitar, be sure to secure the guitar so it will not move when doing such work. B-BAND LTD AND B-BAND, INC. WILL NOT BE RESPONSIBLE FOR ANY DAMAGES, PERSONAL INJURIES OR LIABILITIES RESULTING FROM INSTALLATIONS, IMPROPERLY DONE INSTALLATIONS OR MISUSE OF PRODUCT. 2.
3. OVERVIEW OF A5T PREAMP - Small dress washer - Lock washer - Large dress washer - Large hex nut • 1 pc battery holder with adhesive • 1 pc battery cord harness (length 15 cm / 5.90”) • 2 pcs wire clips • 1 pc instructions and user guide All B-Band A-series preamps are designed to give optimum performance with B-Band UST and AST transducers. The main criterion in designing these preamps was to deliver studio quality and user-friendly electronics to the diverse needs of acoustic instrument musicians.
The cardboard installation template for the 1470 AST is specifically made for bridges that the saddle is at a slight angle to the bridge pinholes. It may also be that the guide is too long for the space. If so, the template can be trimmed with scissors slightly to accommodate this. If in case the template still does not work the transducer may be installed by hand.
.3 Making holes for A5T preamp Find a good position for the preamp at the side of the guitar. Be sure that the position is so, that when the holes are drilled that the holes, and the preamp structure, do not interfere with the any of the guitar braces or supports. For this installation it is very important to check inside the guitar body that there is enough clearance for the preamp at the side between the soundboard and the back of the guitar.
6.4 Installing battery holder Before installing the battery holder it should be checked by inserting a 9-volt battery in and out of it to learn how it works. Once this is checked, find a convenient place inside the guitar where the battery holder can be reached and that there is good access to the snap. Also check that it is in a place that the battery can be put in and out easily. Recommended places are at the neck block or at the back of the guitar.
the extra cord as a “coil” in some of the clamps if necessary. 8. Installing the preamp. For the next portion of the installation, be careful not to catch the pickup on anything as you work; inadvertent tugging may cause damage to the transducers or pull the connectors off the pin headers at the preamp. 9. INSTALLING THE TRANSDUCER If installing UST, do it now. Thread the B-Band UST up from inside the guitar through the hole in the saddle slot.
system will work but it will buzz. • Check that the connectors are inserted correctly onto their pin headers at the preamp. 10.3 Resonance or distortion with some played notes. There are a couple places where a resonance can typically occur with some notes, causing distorted-sounding output. First, check that the lead portion of the transducer to the preamp is not touching anything and that the battery or output wires are not loose and thus cause resonance.
is 0.5 - 0.8 mm (.02” - .03”). This will cure imbalance problems effectively. • A very efficient way is to make the saddle more flexible by modifying it, for example see picture below. Even more efficient it is to cut the saddle into six separate pieces, or to cut it almost through between the strings but leave just a small portion on the bottom side of the saddle, i.e. cut it from the bottom towards the top. • Most of the balance problems are due the fact that the guitar top lives.
Middle control range: ± 12 dB @ 400 Hz (Q = 0.5) Treble control range: ± 12 dB @ 2.5 kHz (Q = 0.5) Presence control range: ± 12 dB @ 12 kHz (± 3 dB @ 2.2 kHz) Nominal output level: -10 dB u (0.245 VRMS) Power supply: 9 V battery (not included) Current consumption: 0.8 mA typical Connections: Transducer input: 2.54 mm (.10”) header; Output: 6,3 mm (.25”) jack Weight (with accessories): 140g Dimensions: L: 86mm (3.38”), W 57mm (2.24”), H 31mm (1.22”). CONTROLS 6 11 8 9 10 1 13.
3. MID (MIDDLE SLIDE CONTROL) 4. TREB (TREBLE SLIDE CONTROL) 5. PRES (PRESENCE SLIDE CONTROL) The Notch Depth and Frequency should be used sparingly as they will affect the tone. Once you experiment with the settings of these controls you will find more about how they work. The BASS, MID, TREB, and PRES slider controls are a 4-band equalizer for controlling tone. 8. PHASE (PHASE BUTTON) The BASS and PRES (presence) tone controls are normal boost / cut shelving controls.
Note LED Display Half Step LED In-Tune LED SETTING UP THE PREAMP FOR USE Tune the guitar. See the tuner instructions at 10 and 11. Before plugging a cable into the guitar’s output jack, slide the volume control OFF (“0”), slide the 4-band EQ controls to “0”; turn the Notch Filter and Frequency rotary controls fully counterclockwise; push the phase button so it is OUT (in phase); and turn the tuner OFF. Flat LED Sharp LED Check that the 9-volt battery is good.
B-BAND LIMITED WARRANTY STATEMENT In the unlikely event that your product needs guarantee service, please contact your dealer, distributor or manufacturer. To avoid any unnecessary inconvenience on your part, we recommend you read this instruction manual carefully before seeking guarantee service. YOUR GUARANTEE By this Guarantee, B-Band guarantees the product to be free from defects in materials and workmanship at the date of original purchase for a period of one (1) year from that date.
A5T opening 1,97 50 2,17 55 PREAMP BOX 15 5 0,0 5 ...
International: B-Band Ltd Konttisentie 8, 02150 Vaajakoski, Finland Tel: +358 14 332 9050 Fax: +358 14 332 9001. Email: sales@b-band.com Internet: www.b-band.com USA: B-Band, Inc. 10909 Vanowen Street, Suite 300 North Hollywood, CA., 91605, USA Tel: (818) 508 9412. Fax: (818) 508 9413. Email: sales@b-bandusa.com Internet: www.b-band.