AUTOMATIC ROLLING GARAGE DOOR OPENER OWNERS COPY Installation Instructions WARNING It is vital for the safety of persons to follow all instructions. Failure to comply with the installation instructions and the safety warnings may result in serious personal injury and/or property and remote control opener damage. Please save these instructions for future reference.
TABLE OF CONTENTS Important Safety Instructions................................... 3 Features.................................................................... 4 Operating Controls...................................................... 5 - 6 Package Contents..................................................... 7 Before Installation.................................................... 8 Mounting the Opener............................................... 9 - 10 Setting Limits.........................
IMPORTANT SAFETY INSTRUCTIONS Warning - It is vital for the safety of persons to follow all instructions. Failure to comply with the following Safety Rules may result in serious personal injury and/or property damage. For ADDITIONAL SAFETY protection we STRONGLY recommend the fitting of a Photo Electric Beam. In most countries Photo Electric Beams are mandatory on all garage doors fitted with automatic openers.
FEATURES Thank you for purchasing the B&D Controll-A-Door® ShedMaster Automatic Rolling Garage Door Opener. This opener is designed to suit vertical operating continuous curtain rolling doors. The components and materials used in this opener are of the latest technology and highest quality. Listed below are some of the many features.
OPERATING CONTROLS 1. P. E. SHUNT. The shunt has to be removed when connecting a Photo Electric Beam. NOTE: P.E. SHUNT must not be removed otherwise the opener will not function correctly. Remove only when a P.E beam is to be connected. 2. STATUS LED (Yellow) indicates when the datum adjustment screw has reached correct position. 3. DATUM ADJUST SCREW Used to set mid point of door travel during limits set up. 4. 7.
MOTOR P.E PROG 24VAC SUPPLY OPERATING CONTROLS 1 10 2 3 4 5 6 12 11 7 8 9 13 1) 2) 3) 4) 5) 6) 7) P.E.
PACKAGE CONTENTS ITEM QUANTITY B&D CONTROLL-A-DOOR® SHEDMASTER DRIVE UNIT 1 HAND HELD TRANSMITTERS WITH VISOR CLIPS 2 WEIGHT BAR 1 PAN HEAD SCREW M4x50mm 2 NILOCK HEX NUT M4 2 FLAT WASHER I.
BEFORE INSTALLATION IMPORTANT SAFETY INSTRUCTIONS FOR INSTALLATION FIG. 1 Warning: Incorrect installation can lead to severe injury. Follow ALL installation instructions. SIDE ROOM REQUIREMENTS Fig. 1 shows the minimum and recommended side room that is required to mount the opener. The distance between the edge of the door curtain and the inside of the bracket must be at least 40mm. However, for easier access it is recommended that at least 95mm is allowed . 1.
MOUNTING THE OPENER 4. FIXING DRIVE UNIT TO THE DOOR FIG. 4 The Drive Assembly can be fixed to the rolling garage door in a variety of ways. Described below is one method of fixing. Make sure there is enough side room to slide the drive assembly onto shaft. PLEASE NOTE: THE INSTRUCTIONS FOR FIXING THE DRIVE ASSEMBLY TO THE DOOR IS FOR RIGHT HAND INSTALLATION. FITTING DRIVE UNIT TO DOOR (Fig. 4, Fig. 5, and Fig. 6). 1.
MOUNTING THE OPENER 5. FIXING OF DOOR CURTAIN TO DRUM WHEEL DRUM WHEEL FIG. 7 The door curtain has to be secured to the drum wheel with suitable fasteners. 1. With the door in the fully closed position, mark the curtain (Fig. 7) on both ends of the door. 2. Open door slightly to have access to the marked positions. Secure the curtain to drum wheel using self drilling screws (two on each end). The screws should be at least 90 degrees apart. 5.1 MOUNTING THE TRANSMITTER BRACKET (Fig. 7.1) 1.
SETTING LIMITS 6. SETTING DOOR TRAVEL LIMITS IMPORTANT NOTE: The OPERATE button will not function until the open and close limits positions are set. FIG. 8 6.1 SETTING DATUM POSITION 1. Switch the opener into manual mode ( 2. Move the door by hand to an approximately mid open position. 3. Re-engage the opener. 4. Using a small blade screw driver turn the datum adjust screw slowly until the yellow status LED just illuminates.
SETTING SAFETY OBSTRUCTION FORCE 8. SAFETY OBSTRUCTION TEST FIG. 11 Please take care when testing the Safety Obstruction Force. Due to Excessive forces failure to follow this warning may cause SERIOUS PERSONAL INJURY and/or property damage. The test below should be repeated at regular intervals (approximately every two months). 8.1 TESTING CLOSE CYCLE 1. Open the door by pressing the OPERATE button (Fig. 11). 2. Place a length of timber approximately 50mm high on the floor directly under the door (Fig.
CODING TRANSMITTERS . FIG. 13 9. SETTING TRANSMITTER CODES Make sure to insert the battery into the transmitter. The memory in the openers receiver can store up to six unique remote control transmitters, one dipswitch transmitter and one entry keypad. 9.1 CODE SETTING THE RECEIVER WITH SMART CODE OR DIP SWITCH TRANSMITTERS 1. Make sure that the battery is inserted in the Transmitter 2. Press the Door Code button on the opener. The Code Set LED will illuminate to indicate the opener is in Code Learn mode.
PE BEAM AND FINAL SET UP 13. FITTING THE SAFETY PHOTO ELECTRIC BEAM SENSOR (OPTIONAL) FIG. 14 Locate the Photo Electric Beam (P.E.) normally closed contact type in a strategic location within doorway. We recommend 150mm above the floor level and as close as possible to the door opening, inside the garage. Remove shunt from P.E connector (Fig. 14) and connect the wires from the P.E. wiring harness as per Fig. 15.
PARAMETERS DOOR STATUS INDICATORS DOOR OPENER STATE OPEN OPEN LED GREEN CLOSE LED RED DOOR STATUS LED YELLOW BEEPER ON ON CLOSE FLASHING OPENING FLASHING CLOSING DOOR TRAVEL STOPPED FLASHING DOOR OBSTRUCTED WHEN OPENING FLASHING FLASHING DOOR OBSTRUCTED WHEN CLOSING OPENER OVERLOADED MAINS POWER INTERRUPTED BEEPS WHILE DOOR IS MOVING FLASHING ALTERNATING FLASHES ALTERNATING FLASHES RAPID FLASHES BUTTONS FUNCTION OPERATE Opens/Stops/Closes the door Door Code Codes a transmitter button
DEFAULT SETTINGS AND SPECIFICATIONS FACTORY DEFAULT SETTINGS DEFAULT STEP MAXIMUM 30 Secs. — — 8 1 20 MAXIMUM MOTOR RUN TIME OBSTRUCTION FORCE MARGIN TECHNICAL SPECIFICATIONS INPUT VOLTAGE: 230V - 240V AC 50Hz CONTROLLER VOLTAGE: 24V DC STANDBY POWER: 2.
TROUBLE SHOOTING SYMPTOM POSSIBLE CAUSE REMEDY Door will not operate. Mains power not switched on. Door is obstructed. Door is locked or motor jammed. Door tracks/hardware damaged. Switch on mains power. Remove obstruction. Unlock door or remove jam. Door requires service/repair by qualified technician. Door starts to close but automatically reverses to open position. Adverse weather conditions (wind or cold) causing door to stiffen and become tight in the tracks. Possible obstruction in the doorway.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23a 23b 24 25 26 27 28 29 DRIVE CHASSIS SUB-ASSY INTERNAL GEAR AXLE HEX SERRATION HEAD SCREW M6X20 INTERNAL GEAR CLAMP WASHER RETAINING RING STW 45 CLAMPING SADDLE BRACKET CLUTCH GEARED MOTOR ASSY 12-01 WS TRANSFORMER TDB-72-01 KIT (72VA) RATCHET TIMING ASSY POWER CORD A.S 1.5M 2P1R FELT 21 X 29 TERMINAL BLOCK 500/02DS 2 POS CAP POLYFILM 0.
WARRANTY AND EXCLUSION OF LIABILITY 1. Definitions ‘B&D’ means (a) in Australia – B&D Doors of 17 Oasis Court, Clontarf Qld 4019, a division of B&D Australia Pty Ltd (ABN 25 010 473 971), or (b) in New Zealand – B&D Doors NZ Ltd of 70 Allens Road East Tamaki Auckland, which is a subsidiary of B&D Australia Pty Ltd (an Australian company). ‘Purchaser’ means the purchaser of the Opener.
WARRANTY AND EXCLUSION OF LIABILITY 10.
