User guide
Table Of Contents
- Section 1 - General information
- Section 2 - Basic operation and key functions
- Section 3 - Radio MENU SELECT options
- 3-1 Manage your waypoints list (WAYPOINT)
- Section 4 - Radio setup menu (RADIO SETUP)
- 4-1 Channel (UIC)
- 4-2 Channel names (CH NAME)
- 4-3 Ring volume (RING VOLUME)
- 4-4 Key beep volume (KEY BEEP)
- 4-5 Select units (UNITS)
- 4-6 Internal speaker connections (INT SPEAKER)
- 4-7 Set the priority channel (WATCH MODE)
- 4-8 Weather alerts (WX ALERT)
- 4-9 NMEA protocol (COM PORT)
- 4-10 Select the GPS source (GPS SOURCE)
- 4-11 Favorite channel setup - Wx key (FAV CH SETU)
- 4-1 Channel (UIC)
- Section 5 - DSC setup menu (DSC SETUP)
- 5-1 Enter or view your USER MMSI (USER MMSI)
- 5-2 Maintain your groups
- 5-3 Enter or check your ATIS MMSI (ATIS MMSI)
- 5-4 Enable ATIS functionality (ATIS SELECT)
- 5-5 Response to individual calls (INDIV REPLY)
- 5-6 Enable DSC functionality (DSC FUNC)
- 5-7 Response type to LL polling calls (LL REPLY)
- 5-8 Automatic channel switching (AUTO SWITCH)
- 5-9 DSC Test Reply (TEST REPLY)
- 5-10 Set the inactivity timer (TIMEOUT)
- 5-1 Enter or view your USER MMSI (USER MMSI)
- Section 6 - AIS setup menu (AIS SETUP)
- Section 7 - Wireless handset setup menu (HS SETTING)
- Section 8 - Sending and receiving DSC calls
- 8-1 What is DSC?
- 8-2 Sending DSC Calls
- 8-3 Send an individual call (INDIVIDUAL)
- 8-4 Acknowledgement of an individual incoming call (INDIV)
- 8-5 Reply to the Last Call (LAST CALL)
- 8-6 Send a group call (GROUP)
- 8-7 Send an all ships call (ALL SHIPS)
- 8-8 Send using the call log (CALL LOG)
- 8-9 Send using the distress log (DIST LOG)
- 8-10 View sent call log (SENT CALL)
- 8-11 Request the LL position of a Buddy (LL REQUEST)
- 8-12 Track your Buddy (TRACK BUDDY)
- 8-13 Make a DSC test call (DSC TEST)
- 8-14 View user MMSI and GPS information
- 8-15 Receiving DSC calls
- 8-16 Receiving an all ships call (ALL SHIPS)
- 8-17 Receiving an individual call (INDIV)
- 8-18 Receiving a group call (GROUP)
- 8-19 Receiving a geographic area call (GEOGRAPH)
- 8-20 Receiving a polled position call (POSITION)
- 8-1 What is DSC?
- Section 9 - DISTRESS calls
- Section 10 - AIS functionality
- Section 11 - General functionality
- Section 12 - Wireless handset functionality
B&G - V50 & H50 Operation Instructions32
4-8 Weather alerts (WX ALERT)
US model only.
Use WX ALERT to set your preferences for weather alert information.
The NOAA provides several weather forecast channels on USA and Canadian channel banks.
If severe weather such as storms or hurricanes are forecast, the NOAA broadcasts a weather
alert on 1050 Hz.
The NOAA All Hazards Weather Radio Service (NWR) works in conjunction with the
Emergency Alert System (EAS) to issue weather alerts for specific geographic areas or specific
weather conditions. It uses a digital encoding system known as SAME (Specific Area Message
Encoding) to broadcast these alerts.
Each transmitter in the NOAA All Hazards Weather Radio Service (NWR) network is identified
with a unique 6-digit SAME code. Each transmitter operates on one of 7 frequencies.
Note: To activate a SAME alert, a SAME CODE (county ID) must be selected and turned ON
(see section 4-8-2).
4-8-1 TONE ALERT
If TONE ALERT is ON and an alert tone of 1050 Hz is broadcast from the NOAA weather
station, the weather alert is picked up automatically and the alarm sounds. Press any key to
cancel the alarm and to hear the weather alert message.
RADIO SETUP
INT SPEAKE▲
WATCH MODE
►WX ALERT
COM PORT ▼
►TONE ALERT
SAME ALERT
SAME CODE
TONE ALERT
►ON
OFF
1. Select RADIO SETUP then WX ALERT.
2. Select TONE ALERT.
3. Select ON to hear any weather alerts on 1050 Hz - the TONE ALERT symbol will be
displayed on the LCD or, to ignore these weather alerts, select OFF.
4-8-2 SAME ALERT
Note: SAME ALERT works only after you have entered and selected a SAME code for your
geographic area (see Section 4-8-5 and 4-8-6).
Note: SCAN mode will operate up to 50% more slowly when SAME ALERT is ON to allow time
to decode the special warning code transmissions.