ZM Series Monitors User Manual ENGLISH bandg.
Preface As Navico is continuously improving this product, we retain the right to make changes to the product at any time which may not be reflected in this version of the manual. Please contact your nearest distributor if you require any further assistance. It is the owner’s sole responsibility to install and use the equipment in a manner that will not cause accidents, personal injury or property damage. The user of this product is solely responsible for observing safe boating practices.
Contents 2 Introduction 2 Items included 3 Display installation 3 3 4 6 Cutout template Fixing options Flush mounting the display VESA mounting the display 7 Connecting the display 7 7 8 9 9 9 9 10 Rear connections Cable retention Connecting power Connecting touch control Serial connection USB connection Connecting NMEA 2000 Typical installation 11 Operating the display 11 11 11 13 13 13 First time operation Shortcut functions OSD menu Updating the firmware Checking current firmware version I
1 Introduction The B&G ZM Series monitors offer a low profile, high brightness solution for displaying video from a variety of sources. This includes two models; the ZM16”, and ZM19” Touch monitors. These models are suited for both indoor and outdoor use. Both monitors accept video via HDMI, DVI-I and composite inputs.
2 Display installation • • • • • • It is recommended that the unit be powered and connected to a video source to assist in selecting a suitable mounting location, prior to irreversible modification of the vessel’s helm station. When planning the display location, the following points should be considered to ensure safe, comfortable and reliable operation: Convenience - the mounting location should be easily accessible to allow operation of the controls and should enable easy viewing of the display.
Flush mounting the display Fit the supplied M4 machine screws, washers, and plastic spacers to each of the four threaded fittings on the back case of screen. Hand tighten only. 1 X4 2 3 x2 200 .0 117.5 mm (4.63") 111.0 mm (4.37") 4 x4 mm mm (7.8 7") mm (7.5 8") (7.3 2") 5 CL 117.5 mm (4.63") 130.0 mm (5.12") .5 .0 6 CLIC 200 K .0 mm .5 186 mm (7.8 .0 7") mm (7.5 (7.38") 192 111.0 mm (4.37") 130.0 mm (5.
Fit brackets to rear of display, aligning ‘key holes’ on bracket with screws on back of display case. With bracket making contact with back of monitor, slide bracket down till it engages with a click and is held in place. CLICK Wind in the wing screw, until stoppers make firm contact with rear of dashboard material. Check front of unit, ensuring that unit’s bezel is making even contact with the dash surface.
VESA mounting the display A VESA bracket adaptor is available as an optional part for all display sizes, allowing a variety of wall and free standing bracket mounting options. The fasteners for attachment to the display are included with the bracket. Monitors mounted using a Vesa bracket have IPX2 rating, and should be mounted in an area sheltered from rain and sea spray. ¼¼ Note: the monitor should not be tilted forward by more than 15 degrees, as this compromises the IPX2 rating.
3 Connecting the display The ZM series monitors largely use industry standard cables, which can be purchased preterminated in a variety of lengths. The following chapter provides additional detail where cables require field termination by the installer.
Connecting power 1234 1 2 3 4 5 + - 6 1 Yellow Wire - power control 2 Blue wire - chassis ground 3 Red wire - positive DC supply (12V or 24V system) 4 Black wire - negative DC supply (12V or 24V system) 5 Fuse - see table at end of section 6 DC supply ¼¼ Note: this display is not intended for use vessels fitted with a positive ground electrical system. The power input cable screen drain wire should be connected to a negative ground. ¼¼ Note: chassis ground will typically not be required.
Connecting touch control The touch screen ZM series monitors can provide touch control to the Zeus2 Processor as well as Windows 7 and Windows 8 PCs. Connection can be made via serial data for Zeus2 Processor or USB for PC systems. Serial connection The ZM series monitors must always be connected to Zeus2 Processor via serial. Make all connections with power turned off.
Typical installation 1 9 8 2 4 3 5 2 6 10 11 7 Key Description 1 ZM16-T or ZM19-T monitor 2 HDMI cable 3 DVI cable (eg. PC, non HDCP sources only) 4 Composite video cable (eg.
5 Operating the display The display is configured and controlled using the row of touch sensitive buttons along the lower edge of the monitor frame. All buttons are backlit - only the power button is illuminated when the monitor is turned off. 1. 2. 3. 4. 5. 6. 7. Power: long press turns display on/off.
Option Sub option HDMI-1 VID-3 VID-4 Option Sub option Range Temperature Allows the user to select colour temperature. The 6500K setting makes the display colour User, 6500K, warmer (slight red tint). The 9300K setting 9300K makes the display colour cooler (slight blue tint).
Option Sub option Range Description Power Control Slave, Master In slave mode monitor will turn on if 12/24V is detected on the yellow wire.
6 Dimensional drawings ZM16: 383mm ZM19: 461mm ZM16: 400mm ZM19: 478mm ZM16: 233mm ZM16: 260mm ZM19: 278mm ZM19: 305mm MAX 25.4 mm (1.00") 8 mm (0.31") 66.0 mm (2.60") MAX 88.0 mm (3.
7 Troubleshooting tips Issue Possible Cause LED on continuously indicates no (compatible) video is available on currently selected source; Confirm that the correct video input is selected No picture - red LED ON Check that the video signal cable is properly connected to the display.
8 Cleaning and maintenance If the display requires cleaning, use a damp soft cloth (e.g. microfiber) with a mild, nonabrasive glass cleaner. Ensure cloth is regularly washed or replaced. ¼¼ Note: Do not use paper products as they may scratch the surface. To minimize the risk of abrasion, allow the screen to air dry. ¼¼ Note: Never use acidic, ammonia based, or abrasive cleaning products to clean the display. These products will damage special coatings on the glass.
Replacing the filters Where displays are installed in an unsealed enclosure, air intake filters should be inspected yearly, and replaced if noticeably fouled. If vessel is subject to major works involving spray painting or sanding, it is recommended that the monitor either be removed, or completely covered in a clean fabric drop cloth. ¼¼ Note: ZM16 and ZM19 models require three filter elements. The filter accessory kit includes five elements.
9 General specifications 15.6” TFT Active Matrix Panel LCD display Brightness 18.5” TFT Active Matrix Panel 1000nit ZM16T = 3.60Kg Weight (monitor only): Screen glass ZM19: 1366x768 AF, AR Protection Thermal: auto screen dimming, overvoltage, reverse polarity, low voltage ZM16: 1366x768 Native resolution ZM19T = 4.
10 Accessories Part description Part number ZM16 bezel trim, silver and black (4 pieces) 000-11620-001 ZM19 bezel trim, silver and black (4 pieces) 000-11621-001 ZM16 Vesa bracket 000-11615-001 ZM19 Vesa bracket 000-11616-001 Cable retention bracket (all models), includes 4 cable ties, screws 000-11614-001 ZM16/19 rear mounting kit 000-11618-001 ZM16/19 dash seal kit (6 pieces) 000-11619-001 ZM16/19 inlet filters (5 pack) 000-11623-001 ZM16/19 inlet filter cover 000-11624-001 HDMI cable
0980 *988-10693-001*
