Specifications

ManualsBrandsB&K ManualsComputer equipmentReference 20

24 BK Radio

QUICK REFERENCE – GROUP 0 (GLOBAL)

RADIO KEYPAD PROGRAMMING

Password

Global Options One

Battery Saver Inhibit 1-12345678

Transmit On Priority 1 1-12345678

Priority 1 Lock 1-12345678

Scan List Lock 1-12345678

Backlight on Display Change 1-12345678

Backlight on Key Press 1-12345678

Silent Mode 1-12345678

Global Options Two

Busy Channel Override 2-12345678

Busy Channel Indicate 2-12345678

Busy Channel Lockout 2-12345678

ANI Only 2-12345678

DTMF Only 2-12345678

DTMF with Manual ANI 2-12345678

Automatic Numeric Identification (ANI)

Transmitter Time-Out Timer

Scan Delay Time

Backlight Duration

Priority 1 Channel/Group

Priority 2 Channel/Group

Flashing number indicates active function.

Keypad Programming Manual 1

TABLE OF CONTENTS

HOW TO PROGRAM RADIOS.............................................................. 2

KEYPAD PROGRAMMING ................................................................... 2

A. NAVIGATION............................................................................ 3

1. Group Parameters (CH 00)............................................... 4

2. Channel Parameters (CH 01 - 20).................................... 4

3. Global Parameters (GRP 00)............................................ 4

B. GROUP PARAMETERS (CH 00) ............................................. 5

1. Group Options: 1-12345678 ............................................. 5

2. Group Label ...................................................................... 6

C. CHANNEL PARAMETERS (CH 01 – 20) ................................. 6

1. Channel Bandwidth........................................................... 7

2. Receive Frequency........................................................... 7

3. Receive Guard.................................................................. 7

4. Transmit Frequency.......................................................... 8

5. Transmit Guard................................................................. 8

6. Channel Label................................................................... 9

D. GLOBAL PARAMETERS (GRP 00) ......................................... 9

1. Keypad Programming Password .................................... 10

2. Global Options One: 1-12345678................................... 10

3. Global Options Two: 2-12345678................................... 12

4. Automatic Numeric Identification (ANI)........................... 14

5. Transmitter Time-Out Timer ........................................... 14

6. Scan Delay Time ............................................................ 15

7. Backlight Duration........................................................... 15

8. Priority 1 Channel ........................................................... 16

9. Priority 1 Group............................................................... 16

10. Priority 2 Channel ........................................................... 17

11. Priority 2 Group............................................................... 17

12. Old-Style BK Priority Scan.............................................. 18

13. Review Global Parameters (GRP 00)............................. 18

E. EXIT PROGRAMMING MODE ............................................... 18

CLONING RADIO SETTINGS ............................................................. 18

TONE CODE GUARD VALUES .......................................................... 22

DIGITAL CODE GUARD VALUES ...................................................... 23

QUICK REFERENCE – GROUP 0 (GLOBAL) .................................... 24

Summary of content (12 pages)

PAGE 1
QUICK REFERENCE – GROUP 0 (GLOBAL) RADIO KEYPAD PROGRAMMING Password Global Options One Battery Saver Inhibit 1-12345678 Transmit On Priority 1 1-12345678 Priority 1 Lock 1-12345678 Scan List Lock 1-12345678 Backlight on Display Change 1-12345678 Backlight on Key Press 1-12345678 Silent Mode 1-12345678 Global Options Two Busy Channel Override 2-12345678 Busy Channel Indicate 2-12345678 Busy Channel Lockout 2-12345678 ANI Only 2-12345678 DTMF Only 2-12345678 DTMF with Manual ANI 2-12
PAGE 2
HOW TO PROGRAM RADIOS DIGITAL CODE GUARD VALUES You can program GPH-CMD radios in three different ways: Codes for the Digital Code Guard system may be chosen from the following list. This can be done during the code programming of the system. Usually systems using direct unit to unit transmission (systems without mobile relays, repeaters, remote control, etc) may use codes from the table. Systems with relays etc. may use code variations for system control and operational efficiency.
PAGE 3
5. Release the [FCN] key and the master switch. The radio is now in the Password Entry Mode. TONE CODE GUARD VALUES The Tone Code Guard system may be set for any frequency in the range of 67 to 255.9 Hz. However, since most systems adhere to the Electronic Industry Association (EIA) standards, tones should be selected from the following EIA list.
PAGE 4
10. If the download was successful, the display on the Master will again display the clone prompt (target and data to be transferred). 1. Group Parameters (CH 00) include: Group Options: 1-12345678 (1-7 = undefined, 8 = group scan list bit) • To clone another channel group, press the Master radio’s [CLR] key. Navigate to a ‘CH’ prompt, then press and hold the [#] key to get the ‘GRP’ prompt.
PAGE 5
PROG|GPHcmD Group 01 Press and Hold [*] Key to Change Target PROG|GPH Group 01 5. Connect the other plug of the cable to the side connector of the radio you want to clone. TX Time-Out Timer Scan Delay 6. Turn on the clone and set it to the desired channel group. Backlight Duration Priority 1 Channel 7. Press the [*] key on the Master radio keypad.
PAGE 6
2. Group Label PROG LABEL 1 GROUP LABEL After Group Options, the display will show the label for the Channel Group. Each Channel Group can have a label of up to twelve characters or spaces. The characters can include 0-9, A-Z, –, -, ., *, +, <, >, /, \, |, $, %, h, or blank. CMND CLN Data that can be cloned to a standard GPH radio includes: If no change is needed, press the [FCN] key to go back to the starting point for Channel 0 settings.
PAGE 7
12. Old-Style BK Priority Scan 1. Channel Bandwidth The radio can be programmed to mimic the Old-Style BK Priority Scan Modes as follows: Mode PR1 TX on PR1 PR2 A Main No Off B Fixed Channel # No Off C Fixed Channel # Yes Off PROG CH 01 N At this point, pressing the [#] key will toggle the channel's bandwidth setting. An 'N' will appear to the right of the channel number when the channel is set for 12.5/15 kHz channel spacing using the narrow band receiver filter.
PAGE 8
PROG RX CG D 023 Rx Guard To enter a Digital Code Guard value press the [#] key, causing the letter ‘D’ to appear followed by three zeros. Enter the desired digital code using keys 0 thru 7 (keys 8 & 9 do not respond). See "Digital Code Guard Values" on page 23 of this manual. Pressing the [PRI] key after the three-digit code has been entered allows the digital code to be inverted.
PAGE 9
Press the [PRI] key to increase backlight duration by 1 second increments from LITE OFF, to 1 SEC ON, 2, 3, 4, 5, 6 SEC ON, LITE ON (illumination remains on constantly) then back to LITE OFF. PROG TX CG D 023 Tx Guard Press the [ENT] key to store changes and advance to the next field. Press the [FCN] key to advance to the next field without storing changes. 8. Priority 1 Channel PROG CHANNEL 1 PRI-1 CHAN After Backlight Duration is set, the ‘Priority 1 Channel’ is displayed.
PAGE 10
seconds). Press the [PRI] key again to change the duration from 225 seconds to zero. 1. Keypad Programming Password PROG Edit-000000 password The current keypad ‘PASSWORD’ is displayed. programming Press the [CLR] key to set the Time-Out Timer duration to zero. If no change is needed, press the [FCN] key to advance to the next field. Press the [ENT] key to store the changed setting and advance to the next field. A new password can be entered by pressing number keys.
PAGE 11
Options Options 6–8: Reserved For Future Option 3: Transmit On Priority 1 When Option 3 is enabled (flashing), transmissions will occur on PR1 (if PR1 isn’t programmed OFF) when operating in Single or Dual Priority Scan Mode. To simulate BK Radio’s Old-Style Priority Mode C, Transmit on Priority 1 must be enabled. Once each option is set as desired, you can store the changes, discard the changes, or disable all displayed options. Press the [CLR] key to disable all displayed options (steady).
PAGE 12
Option 7: Backlight On Key Press PROG 1-12345678 GBL OPTIONS When 0ption 7 is enabled (flashing), the display backlight will illuminate each time a key is pressed, even if pressing the key has no other effect. The display will not illuminate if backlight duration is set to LITE OFF. See "Backlight Duration” on page 15 of this manual. Option 8: Silent Mode PROG 1-12345678 GBL OPTIONS When Option 8 is enabled (flashing), all beeps, tones, and alerts from the radio’s speaker are silenced.