Installation guide

ManualsBrandsB-Tech ManualsTVs & monitorsBT7382

B-TECH AUDIO VIDEO MOUNTS

www.btechavmounts.com

CONTENTS

INSTALLATION TOOLS REQUIRED

FEATURES

BT7382

FULL MOTION DESK MOUNT WITH SINGLE ARM

INSTALLATION GUIDE & PARTS LIST

This Pack Contains 1 Desk Mount

Crosshead

screwdriver

Installation Safety Notes.....................................................................................................................2

Parts List.............................................................................................................................................4

Installation Instructions.......................................................................................................................6

Product Dimensions..........................................................................................................................15

B-Tech Contact Details.....................................................................................................................16

PLEASE KEEP THIS FOR FUTURE REFERENCE

2.5mm Hex Key

(Supplied)

4mm Hex Key

(Supplied)

● Designed for screens up to 24" (61cm) / 9kg (20lbs)

● Fits screens with VESA mounting patterns:

75 x 75mm and 100 x 100mm

● Optional desk clamp and grommet included

● Maximum extension is 390mm (15.4”)

● Easy tilt adjustment +/-40° tilt

● Features two swivel points: 360° at pole and 180° at interface

● Simple installation with all mounting hardware included

Summary of content (16 pages)

PAGE 1
BT7382 FULL MOTION DESK MOUNT WITH SINGLE ARM INSTALLATION GUIDE & PARTS LIST This Pack Contains 1 Desk Mount PLEASE KEEP THIS FOR FUTURE REFERENCE FEATURES ● ● Designed for screens up to 24" (61cm) / 9kg (20lbs) Fits screens with VESA mounting patterns: 75 x 75mm and 100 x 100mm ● Optional desk clamp and grommet included ● Maximum extension is 390mm (15.
PAGE 2
INSTALLATION SAFETY INSTRUCTIONS CAUTION: This mount is intended for use only with the maximum weights indicated. Use with flat screens heavier than the maximum indicated may result in instability causing possible injury. Do not attempt to install this product until all instructions and warnings have been read and properly understood. Please keep these instructions for future reference.
PAGE 3
CS Společnost B-Tech International Ltd. doporučuje provést instalaci tohoto produktu prostřednictvím odborného instalátora AV či jinak způsobilé osoby. Společnost B-Tech International Ltd, její distributoři a prodejci nenesou odpovědnost za škody nebo zranění způsobená nevhodnou instalací. Tento výrobek je nutno umístit do vhodné konstrukce a používat jen po uvedenou maximální výšku. DE B-Tech International Ltd.
PAGE 4
BT7382 PARTS LIST 9 1 2 17 19 10 9 GROMMET CLAMP 15 11 3 6 13 14 4 16 5 11 12 6 13 7 4 8 Suitable for loads up to 9kg (20lbs)
PAGE 5
REF 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 18 19 20 A B C D E A 21 22 PART NAME INTERFACE ASSEMBLY ARTICULATING ARM HEIGHT ADJUSTMENT COLLAR POLE ASSEMBLY TOP CLAMP CLAMP PLATE BOTTOM CLAMP SHORT HANDWHEEL M6 x 15mm HEX SCREW M5 x 5mm GRUB SCREW M6 x 8mm HEX SCREW M10 E-RING M10 METAL WASHER M10 NUT GROMMET PLATE LONG HANDWHEEL POLE END CAP CABLE CLIP CIRCULAR FOAM PAD RECTANGULAR FOAM PAD CABLE TIE 2.
PAGE 6
INSTALLATION INSTRUCTIONS Choose a preferred mounting method. i. Clamp (page 6) ii. Grommet (page 8) 1 i. Desk clamp option. 4 5 11 19 12 20 Max 70mm (2.
PAGE 7
Attach the foam pads to the underside of the clamp base. 19 20 Place the mount over edge of the desk and tighten the short handwheel.
PAGE 8
ii. Grommet Clamp 4 15 11 19 20 6 13 14 16 Max 95mm (3.
PAGE 9
Remove the desk clamp and attach the grommet plate. Then attach the foam pads onto the grommet plate. 23 23 20 19 11 15 11 5 4 4 Place the mount over the cable management hole and screw the handwheel into the grommet plate, then tighten the nut to clamp the desk.
PAGE 10
2 Attach the interface plate to the flat screen. 2 E A B C D 1 T OP T BOT OM FLAT SCREEN 3 To lock height of adjustment collar, hold the top of the collar and rotate the lower part of the adjustment collar.
PAGE 11
4 Slide the flat screen and arm onto the pole, adjust height,then tighten the grub screw. i. FLAT SCREEN 2 3 iii. 4 UNLOCK COLLAR LOCK COLLAR ii.
PAGE 12
5 OPTIONAL : Cable Management. Insert the cable into the cable management slots on the underside of the arm. WARNING: Ensure arm is fully extended before connecting cables. 2 FLAT SCREEN CABLE 2 CABLE 18 4 CABLE 12 CAUTION: Ensure there is adequate cable slack for movement of the screen, and that cables will not be pinched when the mount is closed.
PAGE 13
6 Tighten/loosen the allen screw on the articulating arm to adjust the resistance for tilt.
PAGE 14
7 Tilt and swivel. 22 360° 10 23 9 +/-90° If this does not hold the screen at the required tilt, remove the flat screen from the interface. Then remove plastic nut cover and tighten the M8 nyloc nut.
PAGE 15
BT7382 PRODUCT DIMENSIONS MAX 390mm 15.4" INTERFACE PLATE 100mm 3.9" 75mm 3" 502mm 19.8" 100mm 3.9" 75mm 3" 95mm 3.7" MAX MAX 70mm 2.8" 72mm 2.8" 35mm 1.4" 120mm 4.7" 110mm 4.3" 83.7mm 3.3" 95mm 3.7" O 30mm 1.2" DESK CLAMP, GROMMET & BASE 169mm 6.7" 325mm 12.8" 182mm 7.2" 45° 342mm 13.5" 45° 320mm 12.6" 408mm 16.1" 120mm 4.7" THESE INSTRUCTIONS ARE INTENDED AS A GUIDE ONLY AND B-TECH ACCEPTS NO LIABILITY FOR THE ACCURACY OF THE INFORMATION CONTAINED IN THIS DOCUMENT.
PAGE 16
www.btechavmounts.com B-TECH AUDIO VIDEO MOUNTS HEAD OFFICE Bennett House, Long March, Daventry, Northants NN11 4NR, UK Email: info@btechavmounts.co.uk EUROPE Brixtonlaan 32, Zaventem 1930, Brussels, Belgium Email: info@btechproav.com NORTH AMERICA 203 Eggert Road, Buffalo, NY 14215, USA Email: info@btechavmounts.com ASIA PACIFIC Ruby Industrial Complex, Singapore 347740 Email: info@btechavmounts.com.sg ©2010 Bennett Technologies Limited. All rights reserved.