MODEL: Quattro Product id:QUATTRO13FH Quattro OWNER’S MANUAL
Introduction We thank you for purchasing our amplifiers. Your decision to be part of something different is what we strive for. Our products reflects who we are, going to the extent to deliver you our finest comes natural. Our amplifiers are engineered to accomondate a variety of applications. Whether it is SPL or SQ, the sound provided will be clean & dynamic.
Design features Circuit Configuration: Frequency Response: Signal to Noise Ratio: Input Sensitivity: Crossovers Circuit: High Pass - HPF (CH1 / CH2): High Pass Active - TLA (CH1 / CH2): Tonal Level Adjustment - TLA: High Pass - HPF (CH3 / CH4): Low Pass - LPF (CH3 / CH4): Damping Factor: Bass Boost @ 45 Hz: Remote Control: Fuse Rating: Thermal Protection : Dimensions: Quattro 4 ch class H 9 Hz ~ 42 KHz (+/- 1 dB) > 95 dB 0.
Panel layout Quattro CH1 CH2 HPF TLA SWEET LIKE DANISH CH3 4V 0.2V 4V 0.2V FULL TLA HPF CH1/2 LPF CH4 FRONT REMOTE (CH 3 + 4) REAR RCA signal input for CH 1 & 2. RCA signal input for CH 3 & 4. GAIN GAIN HPF HPF TLA BASS BOOST RANGE LPF Adjusts signal input voltage from the source to match the amplifiers input stage. 0.2 V ~ 4 V is the operational voltage. Voltages beyond may cause damage. Adjusts signal input voltage from the source to match the amp input stage. 0.
Panel layout Head unit Quattro CH2 CH1 CH4 CH3 GROUND BATTERY SPEAKER OUTPUT Connection to the speakers leads. Ensure polarity & corresponding channels are correct. NB! Note the minimum bridged load. Connections below the stated will cause excessive heat & the amplifier can go into thermal. Continious thermal mode can cause damage & void the warranty. + 12V (POWER CONNECTION) Connects to the positive terminal of the battery (+12V). For specified performance 4 GA cable is required.
Installation Installation considerations If you choose to install the amplifier by yourself, please read the owner’s manual carefully. Before you start your installation, please take all steps into consideration. If in doubt, please go to www.b2audio.com for authorized distributors / dealers that will be able to configure your set up & ensure the warranty of your amplifier. Preparation Disconnect the negative (-) battery cable before mounting or making any connection.
Wiring layout Quattro CH1 CH2 HPF TLA SWEET LIKE DANISH CH3 4V 0.2V 4V 0.
Speaker connection CH2 2 ch stereo + 1 ch mono CH1 CH2 CH1 CH4 CH3 Speaker impedance 2 ~ 8 Ohm Speaker impedance 4 ~ 8 Ohm Speaker connection 2 ch bridged CH2 CH1 CH4 CH3 8 CH1 Speaker impedance 4 ~ 8 Ohm CH2 Speaker impedance 4 ~ 8 Ohm
Wiring layout Active Mode (tla) CH1 CH2 HPF TLA SWEET LIKE DANISH CH3 4V 0.2V 4V 0.2V FULL TLA HPF CH1/2 LPF CH4 REMOTE (CH 3 + 4) ACTIVE MODE (TLA) CH1 & CH2 RCA input only. CH3 & CH4 RCA Low Pass signal routed from CH1 & CH2. Low Pass signal routed is dependant of HPF setting of CH1 & CH2. GAIN of CH1 & CH2 is common for all channels, TLA attenuation will adjust signal output to the speakers connected to CH1 & CH2.
Troubleshooting The protection circuits of the amplifier prevents severe damages from faulty conditions & improper use. The protection indicatior will switch on due to short circuit connection & speaker overload, thus the amplifier will be turned off. Prior to inspecting the occurred problem, turn all levels down & all power off, then carefully check the installation for wiring mistakes, shorts or faulty ground (GND).
LIMITED WARRANTY INFORMATION B2 audio offers a limited warranty under the following terms: The product is to be free of defects in material & workmanship under normal use for a period of 1 year from the date of the original purchase, when installed by an authorized dealer. Items not installed by authorized dealers will be warrantied for 30 days from the original purchase. Original sales receips must be accompanied with all returns.
