EN Instructions for Use Instructions for Use for Baby Control Digital breathing monitor: • BC-200 with one sensor pad • BC-210 with two sensor pads • BC-230 with three sensor pads • BC-220i with two sensor pads, may be used with twin babies • BC-230i with four sensor pads, may be used with twin babies
Introduction Dear mum, dear dad! Thank you for purchasing Baby Control Digital breathing monitor. Thus you take a step to ensure safe and undisturbed sleep for your baby and for you as well. Baby Control Digital continuously monitorsyour baby’s breathing movement rate during periods spent in bed, crib or pram, or wherever you use it. We hope you will be satisfied with Baby Control Digital breathing monitor.
Features of Baby Control Digital breathing monitor (BC-200, BC-210, BC-230, BC-220i, BC-230i) 1. Detection is accomplished through the mattress Baby Control Digital breathing monitor has no direct contact with your baby. Its use does not influence the normal life conditions of the family and their baby. It is discreet and easy to use. 2. Uniquely large monitored area The size of one sensor pad is 300 x 500 mm.
Baby Control Digital BC-210 breathing monitor package includes: 1 pc - BC-103 control unit 2 pcs - BC-101 sensor pads wrapped in plastic (without phthalates according to the European standards) 2 pcs - Alkaline AA batteries 1 pc - Instructions for Use Baby Control Digital BC-210 breathing monitor is in control of every function that characterizes the Baby Control Digital product series. Because it has two sensor pads, the device monitors the entire surface of an average size baby bed.
BC-Wireless supplementary unit to Baby Control Digital breathing monitor package includes: 1 pc - BCR-402 Wireless unit 1 pc - BCR-406 small-scale display unit to be worn e.g. around the neck (rechargeable Li accumulator) 1 pc - Instructions for use What to do if the baby’s room is situated far from the parents’ room or from the kitchen where the mother spends a lot of time? The solution is BC-Wireless supplementary unit.
Legend 1 – on/off button 2 – numerical display 3 – two piezo speakers (acoustic alarm) 4 – upper plastic cover 5 – battery compartment (for two alkaline AA batteries) 6 – green indicator light (sensor pad status), BC-220i and BC-230i have double indicator lights, i.e. green and red combined in one 7 – red indicator light (alarm status), BC-220i and BC-230i have double indicator lights, i.e.
Switching ON/OFF your Baby Control Digital breathing monitor (BC-200, BC-210, BC-230) 1. Press and hold the on/off button (1) for 2 seconds. Baby Control Digital breathing monitor will not start by any shorter pressing. 2. The pre-set threshold level of detection will flash on the display (2) five times. The factory setting is „3“. 3. Then the numerical values - „0” = no movement, „1” to „9” = there is any movement - will repeatedly flash on the display (2). 4.
Operation of Baby Control Digital breathing monitor (BC-200, BC-210, BC-230) The numerical display (2) will show the intensity of breathing movements detected by Baby Control Digital approximately every 2.5 seconds („9“ - the most intensive, „1“ - the least intensive, „0“ - no movement detected). At the same time the green indicator light (6) will flash if the intensity of detected movement reaches or exceeds the pre-set threshold value.
How to readjust the threshold level of detection 1. Switch off Baby Control Digital breathing monitor using on/off button (1) and wait for 5 seconds. 2. Then press the on/off button (1) and hold for 20 seconds. The display (2) will show the actual value of threshold level of detection („1“ to „9“), then letters „P”– „L”. Wait until letters „L” – „E” are displayed. 3. Release the on/off button (1) when „L”- „E” (LEVEL) has appeared.
Event memory of Baby Control Digital breathing monitor (BC-200, BC-210, BC-230, BC-220i, BC-230i) Baby Control Digital breathing monitor features 9 minutes event memory which records the events of last 9 minutes before the switch-off (both numbers on the display and acoustic signals). These recordings may become very useful especially when alarm occurs as they make possible to gain information about whether your baby’s breathing pattern before the alarm was regular or not. How to read the event memory 1.
Testing Baby Control Digital breathing monitor (BC-200, BC-210, BC-230, BC-220i, BC-230i) If you wish to try how the Baby Control Digital breathing monitor triggers a warning signal or whether it is ready for operation, then take the baby out of the bed, crib or pram when the device is switched on. The pre-set threshold level of detection will flash several times on the display (2) after switching on.
To ensure proper functioning of the twin mode, each baby must be in placed his/her own bed. Beds must be placed from each other as far as the cables of the sensor pads make it possible, but at least 40 cm. This way the movements of babies will not interfere with one another’s sensor pads. You may test whether the beds are in adequate distance by taking one baby out of the bed.
Operation of Baby Control Digital breathing monitor – TWIN MODE (BC-220i, BC-230i) The numerical display (2) will show the intensity of breathing movements detected by Baby Control Digital approximately every 2.5 seconds („9“ - the most intensive, „1“ - the least intensive, „0“ - no movement detected). At first, the value coming from the left socket (9) is displayed – breathing movements of the baby lying on the sensor pad to the left.
Temporary/permanent suspension of TWIN MODE (BC-220i, BC-230i) Baby Control Digital breathing monitor of BC-220i and BC-230i types for twinsmay also be used for only one baby. Before that the device must be switched from the twin mode into one-baby mode. This meansa permanent switching from one mode to another - not to be confused with a temporary suspension of the twin mode! 1. When switched off, press the on/off button (1) and hold for approximately 30 seconds until letters „S” - „E” appear.
Technical specifications of Baby Control Digital breathing monitor (BC-200, BC-210, BC-230, BC-220i, BC-230i) Control unit (BC-200, BC-210, BC-230, BC-220i, BC-230i) Power supply 3V, 2×1.
Manufacturer’s Declaration of Conformity Declarer’s Name VMD 95 Kereskedelmi és Szolgáltató Kft. Declarer’s Address Színjátszó u. 19, H-1163 Budapest, Hungary Subject of declaration Baby Control Digital breathing monitor system series MSZ EN ISO 13485:2012 MSZ EN ISO 14971:2013 MSZ EN ISO/IEC 17050-1:2010 GYEMSZI/EMKI: Clinically tested. Certification Certification CE 1011 II.b Certificate No. EMKI 5-738-200-1308 EU Manufacturer: VMD 95 Kereskedelmi és Szolgáltató Kft. Színjátszó u.