User guide

ManualsBrandsBaby Control Digital ManualsBaby AccessoriesBC-230

Baby Control

User Guide and Warranty for

• BC-200 one sensor pad,

• BC-210 two sensor pads,

• BC-230 three sensor pads,

• BC-230i four sensor pads for twins

Digital Apnoe Alarm Systems.

Important phone numbers, addresses:

Dear Customer!

Congratulations to you and your newborn baby and to your wisdom in purchasing the “Baby

Control Digital”. Not only will your child be sleeping peacefully!

Some of the features why it worth to choose Baby Control :

• Large Sensor Pads*: the size of the sensor pad is 30 x 50 cm. Depending on the product having 1, 2,

3 or 4 (twins) sensor pads. The product with 3 sensor pads is able to cover the whole resting place of

the baby, even large cots.

• Extra Sensor Pads:* Extra sensor pads can be used at the baby's temporary resting-place. You have to

carry only the control unit.

• Excellent Lateral Sensitivity

• Usable for all mattress models.

• Digital movement display*: luminous display can be clearly seen at night.

• Digitally adjustable sensitivity by 9 degrees*: with the control button you can setup the sensitivity

level (threshold) of the control unit.

• Event Memory*: The control unit stores the event of the last 10 minutes before the alarm.

CE1011

Summary of content (12 pages)

PAGE 1
CE1011 Baby Control User Guide and Warranty for • BC-200 one sensor pad, • BC-210 two sensor pads, • BC-230 three sensor pads, • BC-230i four sensor pads for twins Digital Apnoe Alarm Systems. Important phone numbers, addresses: Dear Customer! Congratulations to you and your newborn baby and to your wisdom in purchasing the “Baby Control Digital”.
PAGE 2
• • • • In case of an alarm it is vital to know and understand the previous events for an examination process. Double Safety Horn* Battery voltage monitor: The control unit warns you, if the batteries are low.
PAGE 3
Functionality The „BABY CONTROL DIGITAL” continuously checks your baby’s breathing and movements to confirm the absence of a possible danger. The BABY CONTROL triggers an acoustic and visual alarm if breathing stops for longer than 12 seconds or if the rate of breathing is bellow 8 breaths per minute. This allows for Apnea (Sudden Infant Death Syndrome) and other life threatening conditions to be indicated in time to save the child.
PAGE 4
Operation 1. Place the sensor pad on the bed bottom. Place the mattress on the sensor pad and be sure that the sensor is well positioned with the mattress using the following guidelines: • Center of the sensor pad should be approximately in the position of where the baby’s chest will be. • The pad should be on a smooth & solid surface – It should not be bent! • If there is only a spring grid supporting the bed, place a solid board (wood, plywood etc.) between the pad and the spring grid.
PAGE 5
3. The green led (6) indicator will flash as the baby breathes or moves. 4. Turn off the unit (press the red button (1) twice) before you take the baby out of the bed. (If the alarm is on the unit can be switched off pressing the red button(1) once) While everything goes well After placing the baby and turning the unit on the digital display(2) shows the sensitivity level every 2 seconds and the green light flashes. (Sensitivity level 9: max, 1: min, 0: no movement (alert)).
PAGE 6
Alarm If the baby is not breathing for longer than 12 seconds, or the breath rate is too slow, after 4 warning signal an alarm signal will sound and the red indicator will flash. On the display(2) the „H”-„E”-„L”-„P” letters will be displayed. (If movement is detected during the 4 warning signal the alarm will not sound. Check the baby and provide first aid if necessary (make sure that there are no reasons for choking, start resuscitation, call for emergency help).
PAGE 7
Test You can test function of the BABY CONTROL in the following way (should be tested once a week): 1. If the baby is in the bed and the unit is ON, the green indicator should flash as the baby is breathing or moving. 2. Leave the unit ON and take the baby out of the bed. The green indicator may continue to blink for a certain time (vibrations of the bed caused by the baby’s removal). Do not hold or touch the bed – the device may detect your breathing. 3.
PAGE 8
1. Place at least one sensor pad under each baby. Connect the sensor pads to the left and the right connection points of the control unit, to identify the sensor pads for each baby. With the given “T” splitter you can also use two sensor pads for each baby. Make sure that you use one “T” splitter for one baby. 2. „Twins” operation switch on - switch off 1. Turn off the BC-230i device 2. Press the button and hold it for at least 30 seconds, until the „S”-„E” sign display. 3.
PAGE 9
Since medicine can not tell them why their baby died, they blame themselves and often other innocent people. Their lives and those around them are changed forever. Being prepared Still today, "cot death" is an unforeseeable occurrence from which every 500th baby dies. 80% of infants affected are entirely healthy beforehand. Only 20% come from so-called risk groups (former premature births or babies already suffering from life threatening conditions or with a "cot death" among close relatives).
PAGE 10
2. Place infants to sleep in a baby bed with a firm mattress. There should be nothing in the bed but the baby - no covers, no pillows, no bumper pads, no positioning devices and no toys. Soft mattresses and heavy covering are associated with the risk for SIDS. 3. Keep your baby’s crib in the parents’ room until the infant is at least 6 months of age. Studies clearly show that infants are safest when their beds are close to their mothers. 4. Do not place your baby to sleep in an adult bed.
PAGE 11
Specification Power: . . . . . . . . . . . . . . . . . . . . . . . . 2 "AA" or "R6" normal battery Control: . . . . . . . . . . . . . . . . . . . . . . microprocessor Operational temperature: . . . . . . . . . + 5 ÷ + 40 °C Operational time: . . . . . . . . . . . . . . . min. 1500 hours with the normal battery Environment:. . . . . . . . . . . . . . . . . . . protect the product against a direct radiant heat from humidity, high vapour content, splashing water Cleaning:. . . . . . . . . . . . . . . . . . . .
PAGE 12
Baby Control Apnoe Alarm Warranty Please ask the retailer to fill the below form! Manufacturing number:.......................... Date: 200…........................... Retailer: .............................................…………… Baby Control is a medical device. It monitors and alerts, but cannot prevent any type of distress. The responsibility of assistance rests on you. Baby Control Digital senses movements and motion only and cannot monitor other occurrences.