Please read the following instructions and warnings carefully. Keep this instruction manual for future reference. Tools required (for wall mouting Camera only): Screwdriver and Drill (not included) For technical support see back page. Adult use only. WARNING: Adult assembly required. Keep small parts away from children when assembling. ® ® INSTRUCTION MANUAL Warnings & Guidelines: WARNING: STRANGULATION HAZARD - Keep cord out of baby’s reach. NEVER place Camera or cords within 3 feet of the crib.
Warnings & Guidelines • Continued WARNING: THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT SUPERVISION. • STRANGULATION HAZARD - Keep cord out of baby’s reach. NEVER place camera or cords within 3 feet of the crib. Use enclosed Security Clips to help secure cord away from baby’s reach. Never use extension cords with AC adapters. Only use the AC adapters provided. • When an AC adapter is plugged into an electrical outlet, do not touch the exposed end.
All Components • 1 Camera, 1 Monitor, 1 Movement Unit • 2 AC Adapters • 6 Cable Clips • 1 Anchor and Wall Mount Screw Camera Movement Unit ® AC Adapters Hardware X1 ® X1 X6 Monitor Features • Camera Power On LED Lens Microphone Movement Unit Charging Station (Place Movement Unit in this to charge) Power On/Off AC Adapter Jack 3
Features • Monitor Menu Pause Alarm Talk Back Power On/Off Video On/Off Volume Toggle Left/Right Sound/Lights Power LED LED Battery Indicator OK/Select/Zoom ® Speaker Microphone Brightness Toggle Up/Down (Underneath) Magnetic Clip for Clothing ® Adjustable Kickstand Battery Compartment AC Adapter Plug Power Button 4
Camera Setup • Adult Assembly Required There is no need to pair any of the components. The Camera, Monitor and Movement Unit have all been synched at the factory. If for any reason pairing is lost, please refer to TROUBLESHOOTING section on page 9. 2 Plug AC Adapter with Camera Icon into Camera CAMERA PLACEMENT : ON FLAT SURFACE 1 TABLE TOP: Place Camera in desired location, plug in AC Adapter to Camera and turn on.
3 4 Tighten screw until only 1/4” (6.3mm) of the screw is exposed (screw driver 1/4” not included). 5 Secure the cord to the wall using the 6 Security Clips included to keep cord away from baby’s reach. UG PL at least 3ft IMPORTANT Be sure to test reception and Camera positioning. IN Monitor Setup • Adult Assembly Required Plug Monitor AC Adapter into Monitor and hold the power button on top of Monitor for 5 seconds. ON Be sure to test your Monitor’s reception before initial use.
Max 30 Feet Max 600 Feet Movement & Positioning Data 1 Press the power button on the center top of the Movement Unit for 4 seconds to power on. You should see movement info and orientation of the baby (side, back, stomach) on the monitor screen. SIDE 100% STOMACH Press power on the movement unit until you hear a beep. BACK ® Research shows that sleeping on their back is the safest position for babies.
Movement Unit Icon Status • On Monitor Screen Charging Icon – This means the Movement Unit is currently in the recharging dock in the Camera and is charging. Movement & orientation information is disabled. The Movement Unit will flash Low an amber or red light every 4 seconds while charging. When fully Battery charged the light will turn green. Charging Si Low Battery Icon – This means the Movement Unit needs to be charged. The Movement Unit will flash a red light.
Alarm Icon – After no movement has been detected for 15 seconds, the Monitor will begin to beep. After 20 seconds of no movement detected, the Alarm icon will appear on the Monitor screen and the Monitor will beep rapidly. pause alarm be Pause Icon – Pressing the Pause button on the Monitor when the Alarm Icon is on the screen and the Monitor is alarming will silence the Alarm for 15 seconds. After 15 seconds, if there is still no movement detected, the alarm will resume.
4 With the Camera powered ON, press the CODE button on the bottom of the Camera. 5 You should see live video on the Monitor. code button 100% ® To Re-Pair the Movement Unit and Camera: 1 Place Monitor and Movement Unit within 3 feet of each other. Power off the Movement Unit (hold the POWER button for 4 seconds) and power on the Camera. OF 2 Press the MENU button on the Monitor and use the RIGHT or LEFT button to move to the Movement Unit icon.
Limited Warranty At Baby Delight, Inc. we make innovative and high quality products for babies, children and their parents. We warrant this product to be free from defects in material and workmanship existing at the time of manufacture for a period of one year from the date of initial purchase (sales receipt is required for proof of purchase). If such a defect is discovered during the limited warranty period, we will, at our sole option, repair or replace your product at no cost to you.
www.babydelight.com info@babydelight.com Macari Baby, Inc.
