Read all instructions BEFORE assembly and USE of product. KEEP INSTRUCTIONS FOR FUTURE USE. Sit N Stand Plus Tandem Stroller with Car Seat Snap N Go Attachment System US PATENT #5,664,795 Instruction Manual Convenience through innovation and thoughtful design 11.07 Copyright © 2006 - 2007, Baby Trend Inc., All Rights Reserved.
WARNINGS WARNING: Please follow all of these instructions to ensure the safety of your child. Keep these instructions for future reference. WARNING: Failure to follow these instructions could result in serious injury or death. Avoid serious injury from falling or sliding out. Always use the safety belts and insure that the children are properly positioned according to these instructions. WARNING: Never leave children unattended.
PARTS Parent Tray Front Wheels Child Tray Foot Rest Stroller Snap N Go Attachment Bar Front/Rear Canopies Jump Seat Pad (optional) Rear Wheels ASSEMBLING TO ENSURE SAFE OPERATION OF YOUR STROLLER, PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. ASSEMBLY 1. Remove stroller from box. The front wheels, rear wheels, child tray, and canopies need to be installed prior to use. 2. To attach the front wheels, unfold stroller as described in the section following.
6. To attach the front child tray, push the tray onto the front frame tube, lining up the tray between the protruding rivets. Push backward on the latch until snapped into place. The protruding rivets on the outside of the frame tube should be between the tray latch. Check that the tray is securely latched in place. Fig. 5 and Fig. 6. 7. To remove front child tray, pull outward on the latches and pull outward on the tray. Fig. 7. Please note that you may attach or remove one end at a time.
TO SECURE REAR STANDING CHILD 1. The rear platform and jump seat are designed to accommodate a child who is at least 2 1/2 years old, has good balance and coordination, and is not over 40 inches tall. Position the child on the platform on the back of the stroller. Be sure child is facing forward and hands are holding frame. Secure the safety belt behind child and engage buckle. Fig. 12. 2. Be sure that the child’s feet are fully on the platform at all times.
STEP TWO: INSTALLING JUMP SEAT PAD (if equipped) 1. Slide the Pad over the front of the Jump Seat platform and into the front pocket of the Pad cover. 2. Insert the safety harness, crotch strap through the Pad in the slot provided. 3. Fold the Pad over the seat and secure conneting the straps together. 4. Have child sit on the jump seat facing backwards. Secure the seat belt, which is attached to the back of the seat, around the child’s waist, and buckle to the crotch strap. Fig. 12B.
BRAKES WARNING: Always set brakes when the stroller is not being pushed so that the stroller will not roll away. Never leave stroller unattended on a hill or incline as the stroller may slide down the hill. Fig. 21. 1. To engage brakes, apply light downward pressure to the brake lever located on each rear wheel. The stroller may require slight forward or rearward movement in order to line up the teeth on the brake with each wheel brake cluster. Fig. 21.
TO UNFOLD STROLLER TO UNFOLD STROLLER Do Not allow children near stroller while unfolding. 1. Release the folding latch, which is located on the right side. Fig. 26. 2. Lift up on the stroller handle with both hands until the stroller frame is erect and locked in the open position. The stroller has spring-loaded latches on both sides of the frame. Test that both latches are fully engaged prior to placing your child in the stroller.
TO USE JUMP SEAT Attention Updated Release 04/18/08 Upper WARNING: Please follow all of these instructions to ensure the safety of your child. Keep these instructions for future reference. Fig. 13 Snap point Lower To Use Jump Seat you must remove the rear seat. STEP ONE: REMOVING THE REAR SEAT 1. Unsnap Rear Canopy buttons from the back of the rear seat. 2. Remove the rear canopy by sliding the square fittings upward until they disconnect from the frame. 3.