Instruction Manual

10 11
Model number PPS1CWE Contact us / 1-877-571-2391 Model number PPS1CWE Contact us / 1-877-571-2391
TROUBLESHOOTING
Problem Possible Solution
Unit not charging • Make sure all of the unit’s functions are turned off.
• Check the connection to the AC power source.
• Confirm there is a functioning AC current.
Wireless Charging
function will not
charge appliance
• Make sure the Wireless Charging Button has been pressed
to turn the Wireless Charging function on.
• Make sure the appliance is placed in the center of the
Wireless Charging Pad.
• Some appliances may not charge/operate with this unit.
Check the manual of the corresponding appliance to
confirm that it can be used with this type of wireless
charging.
• Check that the unit has a full charge. Recharge the unit
if necessary.
Engine fails to jump-
start
• Make sure a proper polarity cable connection has been
established.
• The unit may be overheated due to the excessive engine
cranking. Make sure all the unit functions are turned off
and allow the unit to cool down before resuming operation.
• Make sure the unit is not being operated in the compressor
mode.
• Check that the unit has a full charge. Recharge the unit
if necessary.
Portable Compressor
will not inflate
• Make sure the Compressor Power Button has been
pressed to turn the compressor on.
• Make sure the unit is not being operated in the Jump
Starter mode.
• Make sure the Sure Fit
®
nozzle is securely screwed on
to the valve stem when attempting to inflate tires; or that
the nozzle adapter is securely screwed into the Sure Fit
®
nozzle and is inserted properly into the item to be inflated
on all other inflatables.
• Check that the unit has a full charge. Recharge the unit
if necessary.
USB Power Port will
not power appliance
• Make sure the USB Power Button is in the on position.
• Make sure all the USB Power/Fault Indicators light solid
blue. If a fault condition exists in either of the USB Ports,
the USB Power/Fault Indicators will flash blue. Refer to
the Important Notes in the “USB Ports” section to remedy
any faults.
• Make sure that the total draw of all USB devices plugged
into the two USB Ports does not exceed 3.1A.
• Some USB-powered household electronics will not operate
with this USB charging/power port. Check the manual of
the corresponding electronic device to confirm that it can
be used with this type of USB charging/power port.
• Check that the unit has a full charge. Recharge the unit
if necessary.
LED Area Light does
not come on
• Make sure the LED Area Light Power Button is in the on
position.
• Check that unit has a full charge. Recharge unit if necessary.
ACCESSORIES
Recommended accessories for use with your tool may be available from the
manufacturer. If you need assistance regarding accessories, please contact the
manufacturer at 1-877-571-2391.
WARNING: The use of any accessory not recommended for use with this appliance
could be hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts,
contact the manufacturer at 1-877-571-2391.
TWO-YEAR LIMITED
WARRANTY
The manufacturer warrants this product against defects in materials and workmanship
for a period of TWO (2) YEARS from the date of retail purchase by the original end-user
purchaser (“Warranty Period”).
If there is a defect and a valid claim is received within the Warranty Period, the defective
product can be replaced or repaired in the following ways: (1) Return the product to
the manufacturer for repair or replacement at manufacturer’s option. Proof of purchase
may be required by manufacturer. (2) Return the product to the retailer where product
was purchased for an exchange (provided that the store is a participating retailer).
Returns to retailer should be made within the time period of the retailer’s return policy
for exchanges only (usually 30 to 90 days after the sale). Proof of purchase may be
required. Please check with the retailer for their specific return policy regarding returns
that are beyond the time set for exchanges.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects
resulting from normal wear and tear, accidents; damages sustained during shipping;
alterations; unauthorized use or repair; neglect, misuse, abuse; and failure to follow
instructions for care and maintenance for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you may
have other rights which vary from state to state or province to province. This product is
not intended for commercial use.
APPENDIX
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions: (1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Changes or modifications not explicitly approved by the party responsible for
compliance could void the user’s authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 and part 18 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and candidate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. During the operation of device a distance of 15 cm surrounding the device
and 20 cm above the top surface of the device must be respected.
This device complies with Part 18 of the FCC Rules. This equipment generates uses
and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
INFLATING OTHER INFLATABLES WITHOUT VALVE STEMS
Inflation of other items requires use of the nozzle adapter.
1. Screw the nozzle adapter into the Sure Fit
®
nozzle. Do not overtighten.
2. Insert the nozzle adapter into item to be inflated.
3. Follow steps 2 through 4 of the “Inflating Tires or Products With Valve
Stems” section.
IMPORTANT: Small items such as volleyballs, footballs, etc. inflate very rapidly.
Keep this in mind when setting pressure. Take extra care not to over-inflate.
4. When the desired pressure is reached, the compressor will automatically stop.
Press the Compressor Power Button again to turn off the unit.
5. Disconnect the adapter from the inflated item.
6. Unscrew and remove the nozzle adapter from the Sure Fit
®
nozzle.
7. Allow the unit to cool, then recharge before storing away.
8. Store the compressor hose, Sure Fit
®
nozzle and nozzle adapter in the storage
groove.
USB PORTS
The USB Power Button and the two USB Ports are located on the front of the unit; the
USB Power/Fault Indicator is a translucent ring around each of the USB Ports. Refer to
the “Features” section to locate.
IMPORTANT NOTES
1. The two USB Ports provide a total of 3.1A (5V each).
2. When the USB Ports are in use, the unit will monitor for the following USB fault
conditions on both USB Ports: low battery voltage fault, overload and short circuit.
If low battery voltage fault occurs, the USB Power/Fault Indicators will turn off.
The LCD screen will display the Battery Status Icon and the Voltage Icon for 10
seconds before the unit shuts down automatically. If an Overload Fault or Short-
circuit occurs in either of the USB Ports, the USB Power/Fault Indicators will flash
blue. In any of these cases, the backlit LCD screen will continuously display the
following:
The Fault Icon will flash. The USB Ports will automatically shut down. Should this
occur:
a. Disconnect the USB-powered device and press the USB Power Button again
to turn off the USB Ports immediately.
b. Make sure the unit does not need to be recharged.
c. Allow the unit to cool down for several minutes before attempting to use the
USB Ports again.
d. If an individual USB device is within specifications and the fault occurs, have
the USB device checked for malfunction and do not continue to use it with
these USB Ports.
3. This unit’s USB Ports do not support data communication. They only provide
power to external USB-powered devices.
4. Some household USB-powered electronics will not operate with this unit.
USING THE USB PORTS
1. Press the USB Power Button to turn on both USB Ports. A beep will sound, the
USB Power/Fault Indicators around each of the USB Ports will light blue and the
LCD screen will continuously display the following:
The Battery Status Icon and Battery Voltage Indicator will light solid, as well as the
USB Icon, indicating the USB ports are ready to use.
2. Plug the USB-powered device into the USB power port(s) and operate normally.
3. Press the USB Power Button again to turn off the USB Ports.
Periodically check the unit’s battery status on the backlit LCD screen. Four solid bars in
the battery icon indicates a full battery. When the battery level is nearly empty with only
one solid bar or completely empty with 4 empty bars, the unit must be recharged at this
time or the unit’s built-in low voltage protection will activate. The empty Battery Status
Icon will flash for a short period of time before automatic shut down.
IMPORTANT: Make sure the USB Ports are turned off when the unit is being recharged
or stored.
LED AREA LIGHT
The built-in LED Area Light is controlled by the area light on/off button on the control
panel. Refer to the “Features” section to locate.
1. Press the Area Light Power Button once to turn the light on.
2. Press the Area Light Power Button again to turn the area light off.
When the Area Light Power Button is pressed to turn it on, a beep will sound. The
backlit LCD screen will turn on for 10 seconds (only) and will then continuously display
the Battery Status Icon and the Battery Voltage Indicator.
Periodically check the unit’s battery status on the backlit LCD screen. Four solid bars in
the battery icon indicates a full battery. When the battery level is nearly empty with only
one solid bar or completely empty with 4 empty bars, the unit must be recharged at this
time or the unit’s built-in low voltage protection will activate. The empty Battery Status
Icon will flash for a short period of time before automatic shut down.
IMPORTANT: Make sure the Area Light is turned off when the unit is being recharged
or stored.
CARE AND MAINTENANCE
All batteries lose energy from self-discharge over time and more rapidly at higher
temperatures. When the unit is not in use, we recommend that the battery is charged at
least every 30 days.
From time to time wipe the outside of the appliance with a soft cloth. Do not immerse
the appliance in water.
There are no user-replaceable parts. Periodically inspect the condition of adapters,
connectors and wires. Contact manufacturer to replace any components that have
become worn or broken.
BATTERY REPLACEMENT/DISPOSAL
Battery
Please be advised that the battery is designed to last the service life of the unit
and is not replaceable, removable or serviceable. Service life is dependent on a
number of factors including but not limited to the number of recharge cycles, and
proper care and maintenance of the battery by the end user. Contact manufacturer for
any information you may need.
SAFE BATTERY DISPOSAL
Contains a maintenance-free, sealed, non-spillable, lead acid
battery, which must be disposed of properly. Recycling is
required. Failure to comply with local, state and federal
regulations can result in fines, or imprisonment.
Please recycle.
WARNING:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical
tape to prevent shorting (shorting can result in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
PPS1CWE_ManualENSP_051821.indd 10-11PPS1CWE_ManualENSP_051821.indd 10-11 5/18/2021 3:42:06 PM5/18/2021 3:42:06 PM