Quick start guide

ManualsBrandsBacharach ManualsOxygen EquipmentFyrite® Pro

World Headquarters

621 Hunt Valley Circle, New Kensington, PA 15068

Ph: 724-334-5000 • Fax: 724-334-5001 • Toll Free: 1-800-736-4666

Website: www.mybacharach.com • E-mail: help@mybacharach.com

Printed in U.S.A.

Fyrite

Pro

Quick Start Guide 0024-9393

Rev. 3 – May 2010

This Guide provides basic operating and maintenance information for

Fyrite Pro Model 122E and 125E. Detailed information concerning the

analyzer’s operation, set up, calibration, maintenance, and parts list is

contained in Instruction 0024-9388.

Analyzer Turn On and Warm Up

1. Connect the probe’s flue

gas hose, draft hose, and

thermocouple connector to

the bottom of the analyzer

as shown in Figure 1.

If the optional Combus-

tion-Air Thermocouple is

being used, plug it into

the T-AIR connector.

Summary of content (10 pages)

PAGE 1
Printed in U.S.A. World Headquarters 621 Hunt Valley Circle, New Kensington, PA 15068 Ph: 724-334-5000 • Fax: 724-334-5001 • Toll Free: 1-800-736-4666 Website: www.mybacharach.com • E-mail: help@mybacharach.com If the optional Combustion-Air Thermocouple is being used, plug it into the T-AIR connector. 1. Connect the probe’s flue gas hose, draft hose, and thermocouple connector to the bottom of the analyzer as shown in Figure 1.
PAGE 2
Instruction 0024-9393 2. Push the ENTER button then press either the or button as necessary to display the CO & CO Air Free Screen. If the CO channel is set up for manual zero, and if the CO reading is higher than zero when sampling fresh air, then before proceeding with the test the CO channel must be manually zeroed per Section “CO Channel Zero” on Page 11.
PAGE 3
18 Notes: Fyrite Pro Quick Start Guide Instruction 0024-9393 2 6 0 0 1. 2 F 1 °C mB or button as necessary Instruction 0024-9393 4. Insert the analyzer’s probe into the area to be tested and observe the draft reading on the LCD. 3. The draft reading should be zero when sampling room air. If not, press the button once to display the Draft Zero Screen, and then press the ENTER button to zero the draft channel to ambient atmospheric conditions.
PAGE 4
Instruction 0024-9393 4. Press the ENTER button to select the displayed fuel code and enter the Run Mode. F1 = Natural Gas F2 = Propane F3 = Light Oil F4 = City Gas 3. Press either the or button to step through the fuels codes until the proper fuel is selected. The analyzer defaults to the most recently selected fuel. 2. Turn ON the analyzer as previously described. At the end of warmup the Fuel Screen will be displayed.
PAGE 5
16 Instruction 0024-9393 If the analyzer ‘locks up’ and cannot be turned OFF, reset the microprocessor by removing one of the batteries for 5 seconds. Resetting the Microprocessor If a high CO level is detected at turn OFF, the unit will remain ON with its pump running and display “PUrG CO”. The countdown from 5 will not begin until the detected CO level drops below 50 ppm. Although not recommended, the purging process can be bypassed by pressing the I/O button a second time.
PAGE 6
Atmospheric or Gravity Vented Boiler 80% Eff. Fan Assist or Power Vented Furnace/Boiler Instruction 0024-9393 90% Eff. Condensing Furnace/Boiler Fyrite Pro Quick Start Guide 2 3 . 9 % . 1 % . 5 % 4 1 % 2 9 ° C . 7 ° C . 1 % . 3 % 5 7 p p m 8 0 p p m 0 6 0 0 m B Instruction 0024-9393 Figure 5.
PAGE 7
14 2. Press ENTER to start printing. Instruction 0024-9393 1. With the analyzer in its Run Mode, press the HOLD button twice to display the Print Screen. Then press the button once to display the Print All Screen. Print All Test Data 2. Press ENTER to start printing. 1. With the analyzer in its Run Mode, press the HOLD button twice to display the Print Screen.
PAGE 8
E N T E R . Instruction 0024-9393 Figure 3. Model 122E Run Mode Screens CO2 & O2 TL & Eta qA & Excess Air (LAMBDA) Stack Temperature & Efficiency Draft Zero Stack Temperature & Draft Fuel Select: F1 = Natural Gas F2 = Propane F3 = Light Oil F4 = City Gas Figures 3 and 4 show the order in which the screens are displayed by pressing the ENTER and buttons after the analyzer warms-up and enters its Run Mode. 4.12 Run Mode Screens Fyrite Pro Quick Start Guide Instruction 0024-9393 13 3.
PAGE 9
12 Instruction 0024-9393 1. With the analyzer is in its Run Mode, press the HOLD button twice to display the Print Screen. Note: If no test data has been saved, the option to open the memory for viewing will not be available. Perform the following to open and view saved test data: Opening and Viewing Saved Test Data 3. Press ENTER to save the test data and return to the Hold Mode, or press HOLD to return to the Hold Mode without saving. 2. Press the button once to display the Save Screen.
PAGE 10
Instruction 0024-9393 • Calibrate the analyzer every 6 months to ensure its accuracy. • When storing the analyzer, it’s a good idea to empty the water trap and leave it open to further dry it out. • It is recommended that the analyzer be purged after taking a flue-gas measurement before turning it OFF.