Owner`s manual
Operating Instructions
15
Operating Instructions
14
approximately three meters, however, there is a "spike" reading
where the distance and direction lights fluctuate and the distance
display might flash "SE". At this point, the searching Tracker is
temporarily perpendicular to the vertical aspect of the flux pat-
tern of the buried beacon (Figure G, cross-section view). If you
draw a line in the snow or place a long object on the snow in
the direction you were pointing just before the spike, you can
limit your pinpoint search to that line. Known as "pinpointing on
a line," this technique performed properly is the most efficient
method for pinpointing with the Tracker.
In most cases, the buried beacon will be oriented roughly hori-
zontal, there will be two “spikes,” and the lowest reading will
be between them, as shown in Figure G. If the transmitter is
buried vertically, there will be only one spike and a low reading
on either side. In either case, probe at the lowest reading along
the flux line.
Probing/Digging
At the point where the distance has reached a minimum, probe
the area. Your probe should enter the snow perpendicular to the
slope surface. Once you have confirmed the victim’s location,
leave the probe in the snow and begin digging. To monitor your
progress during a deeper burial, continue to use the Tracker
inside the hole. Upon reaching the victim, first uncover his or her
face. In the event of multiple burials, turn off the victim's beacon
(if possible) before continuing the search for the next victim.
Multiple Burials
Multiple beacon searches are more difficult and complex than
single searches. They require practice and an understanding of
flux lines. A thorough understanding of the Tracker’s special (SP)
mode can also greatly increase the efficiency of the multiple
search, though it is not necessary.
If you begin to receive more than one set of signal data, you
probably have a multiple burial. Stay in search (SE) mode, and
focus on the closest distance reading, attempting to engage that
signal in the center search light. If you are roughly the same dis-
tance from both transmitters, the Tracker will often flash “SE”.
Once you are significantly closer to one signal—and within about
ten meters of it—the Tracker DTS (in SE mode) will “lock” onto
that signal and mask out the others. Once you are locked in, the
Tracker will behave very similar to how it does in a single bea-
con search. Pay attention to the readings you last received from
the other beacon; they will give you an indication of where to go
after finding the closest one.
Once you have located the first beacon (beacon 1), turn it off.
If this is not possible, you might already have a good idea of
where beacon 2 is located. In that case, move in that direction
until the Tracker isolates that signal. If you do not have an idea
of where to look next, then remain in SE mode and take three
steps away from the found victim. Walk in a circle of this radius
around the victim, attempting to acquire another signal in SE
mode. If no signal is acquired, take another three steps back
and repeat up to a maximum of three circles (nine steps). If a
new signal is acquired, pinpoint by bracketing. If no signal is
acquired, return to the point where you abandoned the primary
search and continue the search (in SE mode) from there.
A
DVANCED TECHNIQUE: SPECIAL MODE
For greater efficiency in multiple burials—especially when vic-
tims are close together—use special (SP) mode. This mode
enables the Tracker to display the distance and direction of sig-
nals other than those of the closest beacon. It also reduces the
Tracker’s search “window” to the center three directional lights,
enabling the searcher to mask out beacon 1 and differentiate
ENGLISH
&IGURE(
-ULTIPLEBURIALS
)FTHEFIRSTVICTIMSBEACONCANNOTBE
TURNEDOFFNOVICESSHOULDSTAYIN3%
MODEANDUSETHEhTHREECIRCLE
METHODvTOFINDTHENEXTVICTIM
!DVANCEDUSERSSHOULDUSE30MODE
3TART
M
M
M
DAV Safety Research