BELMONT Wooden Swing Set Model # 2001039 Owner's Manual & Assembly Instructions MANUFACTURED BY: Backyard Discovery 3305 Airport Drive Pittsburg, KS 66762 800-856-4445 WARNING: FOR DOMESTIC USE ONLY. WARNING NOT SUITABLE FOR CHILDREN UNDER 36 MONTHS. SMALL PARTS. average 2 person assembly time assembly time may vary based on skill level For the most up to date assembly manual, to register your set, or to order replacement parts please visit www.backyarddiscovery.
INSTALLATION SERVICES AVAILABLE!* Need a helping hand? Let our team of professionals handle the installation for you! *Installation services are only available to U.S. customers. With Go Con! gure, we bring you 18 years of experience right to your doorstep. We service a wide array of indoor and outdoor recreation products that most consumers don’t have the time or ability to deliver & install themselves.
Owner’s Manual Play Set MISSING A PART? CALL US BEFORE GOING BACK TO THE STORE The store where you made your purchase does not stock parts for this item. If you have assembly questions or you are missing or have damaged parts, please call 1-800-856-4445 you can also visit www.backyarddiscovery.com or e-mail customerservice@backyarddiscovery.
Owner’s Manual Play Set Please read entire booklet completely before beginning the assembly process Please retain these instructions and your receipt for future reference. Keep them in a safe place where you can refer to them as needed. In order to provide you with the most efficient service, it is required that you provide us with the part numbers when ordering parts. For Your Records: Please take time and fill out the information below. This information will be needed for warranty issues.
Owner’s Manual Play Set Operating Instructions and Safety Warnings WARNING: BURN HAZARD • Pay special attention to plastic and metal surfaces as they may be hot enough to cause burns. • Always check the temperature of the product before letting your children play on it. • Remember that the product may cause burns if left in direct sunlight. • Always be aware of the sun and weather conditions, and do not assume that the equipment is safe because the air temperature is not very high.
Owner’s Manual Play Set Positioning Your Playcenter • The playcenter is designed to be installed on a level surface by an adult with an adult helper. Placeinaflat area of your yard to minimize ground preparation. • Choose a level location for the equipment. This can reduce the likelihood of the play set tipping over and loose fill surfacing material washing away during heavy rains. • Place the equipment not less than 6'-7" (2.
Owner’s Manual Play Set APPENDIX A X3.1.3.2 Do not install loose-fill surfacing over hard surfaces such as concrete or asphalt. X3.1.4 Poured-In-Place Surfaces or Pre-Manufactured Rubber Tiles — You may be interested in using surfacing other than loose-fill materials – like rubber tiles or poured-in-place surfaces. X3.1.4.1 Installations of these surfaces generally require a professional and are not “do-it-yourself” projects. X3.1.4.2 Review surface specification before purchasing this type of surfacing.
Owner’s Manual Play Set Instructions for Proper Maintenance IT IS IMPORTANT TO CHECK AND TIGHTEN ALL HARDWARE AT THE BEGINNING AND DURING THE SEASON AS THEY MAY LOOSEN DUE TO WOOD EXPANSION AND CONTRACTION. At the beginning of each play season Additional Maintenance • • • • • • • • • Tighten all hardware. Lubricate all metallic moving parts per manufacturer’s instructions. Check all protective coverings on bolts, pipes, edges, and corners. Replace if they are loose, cracked, or missing.
Owner’s Manual Play Set Instructions for Proper Maintenance Your Backyard Discovery structure is designed and constructed of quality materials. As with all outdoor products it will weather and wear. To maximize the enjoyment, safety and life of your structure it is important that you properly maintain it. About Our Wood Backyard Discovery uses 100% Cedar (C. Lanceolata) wood.
Owner’s Manual Play Set Assembly Tips Protrusion Hazard Incorrect Correct If you see exposed threads and your bolt protrudes beyond the T-Nut you may have over tightened the bolt or used incorrect hardware. If you’ve overtightened, remove the bolt and add washers to eliminate the protrusion. 1/8” Proper Hardware Assembly BOLT Bolt and T-Nut Assembly Tap T-nut into the provided hole. Insert your bolt through the lock washer and insert into the provided hole opposite from the T-Nut.
Owner’s Manual Play Set Assembly Tips ASSEMBLY TIP: Keep and eye out for these boxes which will contain helpful pictures and information making the assembly process as quick and painless as possible. Sorting Wood E1 E2 F1 F2 G1 G2 When removing the wood from the boxes we recommend arranging them by part number before you begin assembly. This will allow for faster assembly and easily identify any parts that may be missing or damaged.
Owner's Manual Tools Required for Installation 12
Owner's Manual Basic Setup Dimensions & Assembly Notes Place the set on level ground, not less than 6'-7" [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. • While assembling unit, take time before and after each phase to make sure fort is level. If fort is not level, assembly will be difficult and improper assembly may result. Extra care must be taken to insure the fort is square.
Parts Identification Owner's Manual Wood Components (Not to Scale) E1 FORT UPRIGHT - W4L13102 (1) 1 3/8"x3 3/8"x89 1/2" (36x86x2273) E2 FORT UPRIGHT - W4L13103 (1) 1 3/8"x3 3/8"x89 1/2" (36x86x2273) E3 FORT UPRIGHT - W2A03016 (1) 1 7/16"x3 3/8"x89 1/2" (36x86x2273) E4 FORT UPRIGHT - W4L13526 E77 ANGLE BRACE - W4L13104 (2) 1 3/8"x3 3/8"x73 1/4" (36x86x1862) (1) 1 3/8"x3 3/8"x89 1/2" (36x86x2273) F1 ANGLE BRACE - W4L13105 (2) 1 3/8"x2 3/8"x18 1/8" (36x60x460) F2 ANGLE BRACE - W4L131
Parts Identification Owner's Manual Wood Components (Not to Scale) H4 FLOOR BRACE - W4L13112 (1) 1"x3 3/8"x34 1/8" (24x86x868) H5 PICNIC TARP SUPPORT - W4L13113 (2) 1"x3 3/8"x24 1/2" (24x86x622) H6 WALL SLAT - W4L13114 (2) 1"x3 3/8"x25 1/2" (24x86x648) H7 PICNIC SUPPORT - W4L13115 (2) 1"x3 3/8"x15 1/4" (24x86x387) H8 PICNIC SUPPORT - W4L13116 (2) 1"x3 3/8"x13 1/2" (24x86x344) H9 PICNIC SUPPORT - W4L13117 (2) 1"x3 3/8"x6 3/4" (24x86x172) H10 FLOOR BRACE - W4L13118 H11 FLOOR JOIST
Parts Identification Owner's Manual Wood Components (Not to Scale) K1 WALL RAIL - W4L13123 (3) 5/8"x5 1/4"x34 7/8" (16x134x887) K2 ARCHED WALL RAIL - W4L13124 (1) 5/8"x5 1/4"x34 7/8" (16x134x887) K3 ARCHED WALL RAIL - W4L13125 K4 WALL RAIL - W4L13126 (1) 5/8"x5 1/4"x34 1/8" (16x134x868) M1 TARP SUPPORT - W4L13127 (1) (2) 5/8"x5 1/4"x34 1/8" (16x134x868) 5/8"x3 3/8"x40" (16x86x1016) M2 FLOOR BOARD - W4L13128 (13) 5/8"x3 3/8"x36 3/4" (16x86x935) M3 TARP SUPPORT - W4L13129 M4 FLOO
Parts Identification Owner's Manual Wood Components (Not to Scale) M8 PICNIC CLEAT - W4L13134 M9 (1) 5/8"x3 3/8"x10 1/8" (16x86x258) (1) M11 (2) M14 (1) M77 (1) WALL RAIL - W4L13137 5/8"x3 3/8"x4 3/4" (16x86x122) M12 (9) 5/8"x3 3/8"x25 1/4" (16x86x640) M71 5/8"x3 3/8"x34 7/8" (16x86x887) SLIDE BRACE - W4L08748 5/8"x3 3/8"x17 1/4" (16x86x438) 5/8"x3 3/8"x6 3/4" (16x86x172) WALL SLAT - W4L13138 FLOOR/TARP SUPPORT - W4L13528 (6) M78 (2) M10 PICNIC CLEAT - W4L13135 (2) M13 (1) WALL RA
Owner's Manual Parts Identification Hardware Components H100115 BOLT WH (30) 5/16x1/2 H100008 BOLT WH (4) 5/16x1 H100027 LAG SCREW WH (40) 5/16x2 H100005 NUT BARREL WH (64) 5/16x7/8 H100028 LAG SCREW WH (2) 5/16x2 1/2 H100004 NUT BARREL WH (4) 5/16 x 5/8 H100010 BOLT WH (20) 5/16x1-1/2 H100011 BOLT WH (6) 5/16x1 3/4 H100031 WASHER LOCK EXT (74) 12x19 H100074 T-NUT (24) 5/16 H100012 BOLT WH (24) 5/16x2 H100030 WASHER LOCK EXT (99) 8x19 H100073 T-NUT (7) 3/8 H100013 BOLT WH (4) 5/16x2 1/4 H100001
Owner's Manual Parts Identification Hardware Components H100088 SCREW PFH (48) 8x1 1/8 H100108 WASHER LOCK INT (4) 8x15 H100083 SCREW TAPPING (9) 14x3/4 H100087 SCREW PFH (30) 8x1 1/4 H100086 SCREW PFH (56) 8x1 1/2 H100106 WASHER FLAT (4) 9x18 H100072 T-NUT (4) 1/4 H100099 SWING HANGER (6) 5/16x9 1/2 H100089 SCREW PFH (9) 8x1 3/4 H100111 SCREW PFH (64) 8x2 H100090 SCREW PFH (30) 8x2 1/2" H100095 WASHER SPLIT (4) 5/16 H100105 WASHER FLAT (15) 8x27 H100006 NUT BARREL WH (4) 5/16x1 1/2 H100103 WA
Owner's Manual Parts Identification Accessory Components (Not to Scale) A100054 (1) A100055 (1) A100028 (2) SLIDE RAIL 8' GREEN RIGHT SLIDE RAIL 8' GREEN LEFT A100164 BYD ID TAG (LARGE) AGES 3-10 (1) A100060 A6P00386 (1) HAND GRIP GREEN PLASTIC (6) CLIMBING ROCK GREEN SMALL SLIDE BED 8' DARK GREEN A100314 (1) A100294 (2) "A" REVISION TAG A100069 QUICK LINK (6) TRIANGLE PLATE 100° 5 HOLE A4M01046 (8) A6P00034 (1) TRAPEZE YELLOW A6P00054 (2) A100053 (4) L BRACKET 2.
Owner's Manual Parts Identification Accessory Components (Not to Scale) (1) PICNIC TABLE TARP A4M00527 (6) GROUND STAKE REBAR 21 (2) (2) A100042 A6P00383 T-40 TORX WRENCH ROOF TARP T-40 TORX BIT (1) A100041 A6P00382
SLIDE ASSEMBLY A6P00386 (x1) STEP 1 M77 SLIDE BRACE - W4L08748 (x1) 5/8"x3 3/8"x17 1/4" (16x86x438) SLIDE BED 8' DARK GREEN H100115 BOLT WH (x3) 5/16x1/2 H100074 T-NUT (x3) 5/16 PLACE 'M77' SLIDE BRACE BOARD 1/4" FROM THE BOTTOM EDGE OF THE SLIDE BED. USING THE BOARD AS A TEMPLATE, MARK WHERE THE PILOT HOLES WILL BE DRILLED. USE A 3/8" DRILL BIT TO DRILL THE PILOT HOLES INTO THE SLIDE BED. ATTACH THE SLIDE BED SUPPORT BOARD USING THE HARDWARE PROVIDED. TIP: PREBENDING THE ENDS WILL EASE ASSEMBLY.
SLIDE ASSEMBLY STEP 2 A100054 (x1) M78 (x2) SLIDE RAIL 8' GREEN RIGHT CENTER SLIDE BRACE - W4L08749 5/8"x3 3/8"x17 1/4" (16x86x438) A100055 (x1) SLIDE RAIL 8' GREEN LEFT H100090 SCREW PFH (x24) 8x2 1/2" NOTE: USING A 1/8" DRILL BIT, DRILL PILOT HOLES IN EACH INDENTATION ALONG EACH SIDE RAIL. THERE SHOULD BE 12 INDENTIONS ON EACH RAIL. PLACE THE SLIDE RAIL ON FLAT SURFACE. STARTING AT THE BOTTOM, INSERT THE SLIDE BED INTO THE CHANNEL ON THE INSIDE OF THE RAIL.
SWING BEAM ASSEMBLY SB74 (1) STEP 1 SWING BEAM - W4L13423 2"x5 1/4"x89 1/2" (50x134x2274) A100294 (2) H100047 BOLT HEX (2) 5/16x2 3/4 TRIANGLE PLATE 100° 5 HOLE H100105 WASHER FLAT (4) 8x27 H100011 BOLT WH (3) 5/16x1 3/4 A100140 L BRACKET (2) 66x66x127 H100110 NUT LOCK (2) 5/16 H100005 NUT BARREL WH (3) 5/16x7/8 140 (x2) L BRACKET 66x66x127 047 (x2) BOLT - 2 3/4" 105 (x2) WASHER - 8x27 105 (x2) WASHER - 8x27 110 (x2) 011 (x3) NUT - 5/16" BOLT - 1 3/4" SB74 (x1) SWING BEAM 005 (x3) NUT BA
SWING BEAM ASSEMBLY W71 (1) STEP 2 H79 SWING BEAM SUPPORT - W4L13424 2"x3 3/8"x46 1/8" (50x86x1170) E77 (1) H80 ANGLE BRACE - W4L13104 (1) 1 3/8"x3 3/8"x73 1/4" (36x86x1862) (2) H100021 BOLT WH (1) 5/16x4 1/2 H100014 BOLT WH (2) 5/16x2 1/2 END SUPPORT - W4L13120 1"x3 1/2"x42" (24x86x1072) GROUND BOARD - W4L13121 1"x3 3/8"x87 3/8" (24x86x2218) H100012 BOLT WH (4) 5/16x2 H100031 WASHER LOCK EXT (7) 12x19 H100027 LAG SCREW WH (2) 5/16x2 H100005 NUT BARREL WH (5) 5/16x7/8 H100006 NUT BARREL WH
SWING BEAM ASSEMBLY STEP 3 (1) SWING BEAM SUBASSEMBLY H100011 BOLT WH (2) 5/16x1 3/4 (1) SWING BEAM END SUBASSEMBLY H100005 NUT BARREL WH (2) 5/16x7/8 011 (x2) BOLT - 1 3/4" 006 (x2) NUT BARREL - 1 1/2" SWING BEAM SUBASSEMBLY SWING BEAM END SUBASSEMBLY 26
SWING BEAM ASSEMBLY STEP 4 H100099 SWING HANGER (6) 5/16x9 1/2 H100103 WASHER SAFETY (6) 17x30 H100105 WASHER FLAT (6) 8x27 H100110 NUT LOCK (6) 5/16 110 (x6) NUT - 5/16" 105 (x6) WASHER - 8x27 103 (x6) WASHER - 17x30 099 (x6) SWING HANGER - 9 1/2" 27
ROCK LADDER ASSEMBLY M71 (6) ROCK BOARD - W4L13140 5/8"x3 3/8"x20 1/4" (16x86x514) M72 (2) STEP 1 H73 ROCK WALL SLAT - W4L13421 5/8"x3 3/8"x20 1/4" (16x86x514) (2) ROCK WALL RAIL - W4L13119 1"x3 3/8"x48 3/4" (24x86x1238) H100086 SCREW PFH (32) 8x1 1/2 NOTE: 1. Assemble slats to rails as shown. 2. Note orientation of slats, be sure to arrange as shown. 3. See drawing below for slat spacing on rails. 4. Using slats as a guide, pre-drill top edges of rails with a 1/8" drill bit.
ROCK LADDER ASSEMBLY STEP 2 A100060 CLIMBING ROCK (6) GREEN SMALL H100088 SCREW PFH (6) 8x1 1/8 H100001 BOLT FA (6) 3/8x1 1/2 H100073 T-NUT (6) 3/8 NOTE: 1. Install T-nuts before attaching rocks. 2. Orient top edge of rocks with top edge of slats. 3. Fasten rocks as shown.
FORT ASSEMBLY E2 FORT UPRIGHT - W4L13103 (1) 1 3/8"x3 3/8"x89 1/2" (36x86x2273) E3 FORT UPRIGHT - W2A03016 (1) STEP 1 1 7/16"x3 3/8"x89 1/2" (36x86x2273) G1 (1) H2 FLOOR JOIST - W4L13111 (1) 1"x3 3/8"x34 1/8" (24x86x868) K4 WALL RAIL - W4L13126 (1) G2 1"x5 1/4"x59 1/2" (24x134x1511) (1) H100027 LAG SCREW WH (2) 5/16x2 N1 (1) WALL RAIL - W4L13422 5/8"x1 1/8"x34 1/8" (16x30x868) 1"x5 1/4"x34 1/8" (24x134x868) H100005 NUT BARREL WH (14) 5/16x7/8 H100031 WASHER LOCK EXT (14) 12x19 012
FORT ASSEMBLY E1 (1) FORT UPRIGHT - W4L13102 (1) 1 3/8"x3 3/8"x89 1/2" (36x86x2273) E4 FORT UPRIGHT - W4L13526 (1) G1 STEP 2 K3 (1) ARCHED WALL RAIL - W4L13125 5/8"x5 1/4"x34 1/8" (16x134x868) 1 3/8"x3 3/8"x89 1/2" (36x86x2273) H1 GROUND BOARD - W4L13107 1"x5 1/4"x59 1/2" (24x134x1511) H100012 BOLT WH (6) 5/16x2 (1) H100030 WASHER LOCK EXT (10) 8x19 H100010 BOLT WH (4) 5/16x1-1/2 ROOF CROSS BRACE - W4L13110 1"x3 3/8"x53 7/8" (24x86x1368) H100005 NUT BARREL WH (10) 5/16x7/8 H100031 WASHE
FORT ASSEMBLY M3 (2) M5 (1) M13 TARP SUPPORT - W4L13129 WALL RAIL - W4L13139 5/8"x3 3/8"x34 7/8" (16x86x887) (1) 5/8"x3 3/8"x36 3/4" (16x86x935) WALL RAIL - W4L13131 M14 5/8"x3 3/8"x34 7/8" (16x86x887) H100027 LAG SCREW WH (20) 5/16x2 STEP 3 K1 WALL RAIL - W4L13123 (3) 5/8"x5 1/4"x34 7/8" (16x134x887) FLOOR/TARP SUPPORT - W4L13528 5/8"x3 3/8"x34 7/8" (16x86x887) (1) K2 ARCHED WALL RAIL - W4L13124 (1) 5/8"x5 1/4"x34 7/8" (16x134x887) H100005 NUT BARREL WH (4) 5/16x7/8 H100115 BOLT WH (8
FORT ASSEMBLY H2 (1) FLOOR JOIST - W4L13111 1"x3 3/8"x34 1/8" (24x86x868) H10 (4) STEP 4 FLOOR BRACE - W4L13118 1"x3 3/8"x3 3/8" (24x86x86) F1 (2) H4 (1) FLOOR BRACE - W4L13112 1"x3 3/8"x34 1/8" (24x86x868) H11 (1) H100090 SCREW PFH (4) 8x2 1/2" 1 3/8"x2 3/8"x18 1/8" (36x60x460) FLOOR JOIST - W4L13527 1"x3 3/8"x34 1/8" (24x86x868) H100013 BOLT WH (2) 5/16x2 1/4 H100015 BOLT WH (4) 5/16x2 3/4 ANGLE BRACE - W4L13105 H100027 LAG SCREW WH (2) 5/16x2 H100031 WASHER LOCK EXT (4) 12x19 H100005 NUT
STEP 5 FORT ASSEMBLY M2 (8) M7 FLOOR BOARD - W4L13128 5/8"x3 3/8"x36 3/4" (16x86x935) (2) H100087 SCREW PFH (20) 8x1 1/4 FLOOR BOARD - W4L13133 5/8"x3 3/8"x32 1/8" (16x86x815) H100111 SCREW PFH (40) 8x2 M2 (x8) FLOOR BOARD 111 (x40) SCREW - 2" M7 (x2) FLOOR BOARD 087 (x20) SCREW - 1-1/4" 34
STEP 6 FORT ASSEMBLY H2 (1) M10 (2) M6 WALL RAIL - W4L13132 M11 WALL RAIL - W4L13137 FLOOR JOIST - W4L13111 1"x3 3/8"x34 1/8" (24x86x868) (1) WALL RAIL - W4L13136 5/8"x3 3/8"x6 1/4" (16x86x160) H100012 BOLT WH (2) 5/16x2 (2) H100027 LAG SCREW WH (4) 5/16x2 5/8"x3 3/8"x4 3/4" (16x86x122) H100030 WASHER LOCK EXT (8) 8x19 H100010 BOLT WH (2) 5/16x1-1/2 030 (x2) 5/8"x3 3/8"x34 7/8" (16x86x887) H100005 NUT BARREL WH (4) 5/16x7/8 H100031 WASHER LOCK EXT (4) 12x19 031 (x2) WASHER - 12x19 WASH
FORT ASSEMBLY H6 WALL SLAT - W4L13114 (2) 1"x3 3/8"x25 1/2" (24x86x648) STEP 7 A100053 (2) H100086 SCREW PFH (8) 8x1 1/2 L BRACKET 54x67 - GRN H100083 SCREW TAPPING (4) 14x3/4 REPEAT FOR OTHER SIDE H6 (x2) WALL SLAT 086 (x4) SCREW - 1 1/2" 053 (x2) L BRACKET 54x67 - GRN 083 (x4) SCREW - 14x3/4" 086 (x4) SCREW - 1 1/2" REPEAT FOR OTHER SIDE 36
STEP 8 FORT ASSEMBLY M12 WALL SLAT - W4L13138 5/8"x3 3/8"x25 1/4" (16x86x640) (4) H100088 SCREW PFH (8) 8x1 1/8 H100087 SCREW PFH (8) 8x1 1/4 M12 (x4) WALL SLAT 088 (x8) SCREW - 1 1/8" 087 (x8) SCREW - 1-1/4" 37
STEP 9 FORT ASSEMBLY M12 WALL SLAT - W4L13138 (5) 5/8"x3 3/8"x25 1/4" (16x86x640) J1 WALL SLAT - W4L13122 (2) 1"x2 3/8"x25 1/2" (24x60x648) A100053 H100088 SCREW PFH (20) 8x1 1/8 (2) H100086 SCREW PFH (8) 8x1 1/2 L BRACKET 54x67 - GRN H100083 SCREW TAPPING (4) 14x3/4 M12 (x5) WALL SLAT 088 (x10) SCREW - 1 1/8" J1 (x2) WALL SLAT 086 (x8) SCREW - 1 1/2" 083 (x4) SCREW - 14x3/4" 088 (x10) SCREW - 1 1/8" 053 (x2) L BRACKET 54x67 - GRN 38
STEP 10 FORT ASSEMBLY 1 1/4 in [33 mm] TOP TOP H5 PICNIC TARP SUPPORT - W4L13113 (2) 1"x3 3/8"x24 1/2" (24x86x622) M3 (1) TARP SUPPORT - W4L13129 5/8"x3 3/8"x36 3/4" (16x86x935) H100115 BOLT WH (4) 5/16x1/2 H100027 LAG SCREW WH (2) 5/16x2 H100031 WASHER LOCK EXT (2) 12x19 A4M01046 (2) L BRACKET 2.
STEP 11 FORT ASSEMBLY F2 ANGLE BRACE - W4L13106 H8 PICNIC SUPPORT - W4L13116 (2) 1 3/8"x2 3/8"x12 1/4" (36x60x310) (2) 1"x3 3/8"x13 1/2" (24x86x344) H100013 BOLT WH (2) 5/16x2 1/4 M2 FLOOR BOARD - W4L13128 (3) 5/8"x3 3/8"x36 3/4" (16x86x935) H100027 LAG SCREW WH (6) 5/16x2 H100088 SCREW PFH (6) 8x1 1/8 M2 (x3) FLOOR BOARD M8 PICNIC CLEAT - W4L13134 (1) 5/8"x3 3/8"x10 1/8" (16x86x258) H100030 WASHER LOCK EXT (8) 8x19 H100074 T-NUT (2) 5/16 H100111 SCREW PFH (12) 8x2 111 (x12) SCREW -
STEP 12 FORT ASSEMBLY G3 (2) PICNIC SUPPORT - W4L13109 1"x5 1/4"x5 1/4" (24x134x134) M2 (2) H100088 SCREW PFH (4) 8x1 1/8 H100010 BOLT WH (8) 5/16x1-1/2 H9 (2) PICNIC SUPPORT - W4L13117 1"x3 3/8"x6 3/4" (24x86x172) (2) M9 FLOOR BOARD - W4L13128 5/8"x3 3/8"x36 3/4" (16x86x935) (1) H100111 SCREW PFH (8) 8x2 H7 PICNIC SUPPORT - W4L13115 1"x3 3/8"x15 1/4" (24x86x387) PICNIC CLEAT - W4L13135 5/8"x3 3/8"x6 3/4" (16x86x172) H100030 WASHER LOCK EXT (8) 8x19 H100089 SCREW PFH (6) 8x1 3/4 H100005 NU
FORT ASSEMBLY M1 (2) TARP SUPPORT - W4L13127 5/8"x3 3/8"x40" (16x86x1016) H100008 BOLT WH (4) 5/16x1 M4 (1) STEP 13 FLOOR/TARP SUPPORT - W4L13130 5/8"x3 3/8"x34 7/8" (16x86x887) H100030 WASHER LOCK EXT (4) 8x19 A4M01046 L BRACKET 2.
FORT ASSEMBLY A6P00382 (1) STEP 14 H100128 SCREW PWH (6) 8x5/8 ROOF TARP 382 (x1) ROOF TARP 1 7/8 in [47 mm] 128 (x6) SCREW - 5/8 REPEAT FOR OTHER SIDE 43
FORT ASSEMBLY STEP 15 H100128 SCREW PWH (6) 8x5/8 A6P00383 (1) PICNIC TABLE TARP 1 7/8 in [47 mm] TYP 128 (x6) SCREW - 5/8 383 (x1) PICNIC TABLE TARP 44
STEP 16 FORT ASSEMBLY A100028 (2) H100062 BOLT PTH (4) 1/4x1 1/4 HAND GRIP GREEN PLASTIC H100108 WASHER LOCK INT (4) 8x15 H100106 WASHER FLAT (4) 9x18 028 (x2) HAND GRIP GREEN PLASTIC 072 (x4) T-NUT - 1/4" 062 (x4) 106 (x4) BOLT - 1/4x1 1/4" WASHER - 9x18 108 (x4) WASHER - 8x15 45 H100072 T-NUT (4) 1/4
FORT ASSEMBLY STEP 17 (1) 4 FT ROCK LADDER H100028 LAG SCREW WH (2) 5/16x2 1/2 H100030 WASHER LOCK EXT (2) 8x19 Using 'M13' ladder attachment holes as a guide,predrill these edges. 'M13' ladder attachment holes.
FORT ASSEMBLY STEP 18 9208100 8 FT - FLAT PACK SLIDE (1) H100115 BOLT WH (3) 5/16x1/2 H100074 T-NUT (3) 5/16 12 3/4 in [324 mm] 9 in [229 mm] 2 3/4 in [70 mm] 1 3/8 in [36 mm] 1 in [25 mm] SLIDE BED DRILLING PATTERN 115 (x3) BOLT - 1/2" 074 (x3) T-NUT - 5/16" 47
FORT ASSEMBLY (1) 4 FT SWING BEAM ASSEMBLY H100042 BOLT HEX (4) 5/16x1 1/4 STEP 19 A100164 BYD ID TAG (LARGE) AGES 3-10 (1) H100095 WASHER SPLIT (4) 5/16 H100105 WASHER FLAT (4) 8x27 A100314 H100074 T-NUT (4) 5/16 (1) "A" REVISION TAG H100128 SCREW PWH (6) 8x5/8 NOTE: INSERT T-NUTS BEFORE ATTACHMENT OF SWING BEAM.
FORT ASSEMBLY A6P00034 (1) TRAPEZE YELLOW STEP 20 A100069 QUICK LINK (6) A100083 (2) A100087 (4) A6P00054 (2) SWING SEAT GREEN 22IN ROPE-CHAIN GREEN 33" ROPE-CHAIN GREEN 51.25" INSERT CHAIN ONTO QUICK LINK SWING HANGER, THEN TIGHTEN SWING HANGER COUPLING. NOTE: WHEN HANGING YOUR SWINGS IT IS RECOMMENDED THAT THE BOTTOM OF THE SWING SEAT, WHEN SITTING ON IT, IS LOCATED NO LOWER THAN (35 cm) 13 7/8 INCHES FROM THE GROUND. 087 (x4) ROPE-CHAIN GREEN 51.
FINAL ASSEMBLY A4M00527 (6) STEP 21 H100115 BOLT WH H100005 NUT BARREL WH (6) (6) 5/16x1/2 5/16x7/8 H100031 WASHER LOCK EXT (6) 12x19 GROUND STAKE REBAR NOTE: FAILURE TO USE GROUND STAKES CAN VOID WARRANTY AND CAUSE INJURY! 1. DRIVE REBAR GROUND STAKE INTO THE GROUND AT A 45 ° ANGLE NEXT TO THE GROUND BOARD, IN THE LOCATIONS SHOWN. 005 (x4) 527 (x2) NUT BARREL - 7/8" GROUND STAKE REBAR 031 (x4) WASHER - 12x19 2. USE HARDWARE PROVIDED TO SECURE THE REBAR GROUND STAKE TO THE GROUND BOARD.
