Yukon III Wooden Swing Set Model: 35211 • Owner's Manual • Frequently Asked Questions • Assembly Instructions • Warranty Information Manufacturer: Backyard Discovery 3001 North Rouse Pittsburg, KS 66762 1-800-856-4445 Register your new swing set on-line @ www.swingsetonline.com (you will also find any updates on assembly instructions and information to order replacement parts) Features the fastening system.
STOP PARE Missing A Part? CALL US BEFORE GOING BACK TO THE STORE! The store where you made your purchase does not stock parts for this item. If you have assembly questions or if you need parts, whether they are missing or damaged Call Toll-Free Help Line or visit www.swingsetsonline.com ¡LLÁMENOS ANTES DE REGRESAR A LA TIENDA! La tienda donde realizó la compra no almacena piezas de este producto.
Owner’s Manual Play Set Dear Customer: Please read entire booklet completely before beginning the assembly process. Equipment is recommended for use by children 3 to 10 years of age. Structures are not intended for public use. The Company does not warranty any of its residential structures subjected to commercial use such as: Daycare, Preschool, Nursery School, Recreational Park, or any similar Commercial Application.
Owner’s Manual Play Set Please refer to the Assembly section of the Assembly Manual for Maximum Fall Height. Positioning Your Playcenter 1. The Playcenter is designed to be installed on a level surface by an Adult with an Adult helper. Place in a flat area of your yard to minimize ground preparation. 2. Choose a level location for the equipment. This can reduce the likelihood of the play set tipping over and loose-fill surfacing material washing away during heavy rains. 3.
Owner’s Manual Play Set The following chart explains the fall height in feet from which a life threatening head injury would not be expected Critical Heights in feet (m) of Tested Materials Material Uncompressed Depth Compressed Depth Wood Chips Double-Shredded bark mulch Engineered Wood Fibers Fine Sand Coarse Sand Fine Gravel Medium Gravel 6" (152mm) 7' (2.13m) 6' (1.83m) 6' (1.83m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 5' (1.52m) 9" (228mm) 10' (3.05m) 10' (3.05m) 7' (2.13m) 5' (1.52m) 5' (1.52m) 7' (2.
Owner’s Manual Play Set 18. Verify that any suspended climbing ropes, chain, or cable are secured at both ends and that they cannot be looped back on it. 19. Instruct children not to attach items to the playground equipment that are not specifically designed for use with the equipment, such as, but not limited to, jump ropes, clothesline, pet leashes, cables and chain as they may cause a strangulation hazard. 20. Instruct children to never wrap their legs around swing chain. 21.
Owner’s Manual Play Set Additional Maintenance: • Check the swing beam and hardware every two weeks due to wood expansion and contraction. It is particularly important that this procedure be followed at the beginning of each season. • Inspect wood parts monthly. The grain of the wood sometimes will lift in the dry season causing splinters to appear. Light sand may be necessary to maintain a safe playing environment.
Owner’s Manual Play Set APPENDIX A Information on Playground Surfacing Materials: The following information is from the United States Consumer Product Safety Commission’s Information Sheet for playground surfacing material; also see the following website for additional information: www.cpsc.gov/cpscpub/pubs/323.html. X3. SECTION 4 OF THE CONSUMER PRODUCT SAFETY COMMISSION’S OUTDOOR HOME PLAYGROUND SAFETY HANDBOOK9 X3.
Owner’s Manual Play Set The American Society for Testing and Materials takes no position respecting the validity of any parent right asserted in connection with any item mentioned in this standard. Users of this standard are expressly advised that determination of the validity of any such parent rights, and the risk of infringement of such rights, are entirely their own responsibility.
Play Set Assembly Manual FAQs: 1. Does the area for the playset need to be level? Yes. Backyard Discovery recommends the playset be positioned on a flat level area for maximum safety and durability. The stakes provided should be used to secure it firmly to the ground. 2. What size area is recommended for the playset? Backyard Discovery recommends at least a 6’ (six foot) perimeter around and above the playset for maximum safety. 3.
www.swingsetsonline.com/support.aspx and follow the prompts to order them. Next, read the assembly manual and get the tools ready for the job as recommended in the manual. If the assembly manual is lost or misplaced a new one can be printed from Backyard Discovery’s website: www.swingsetsonline.com. 9. The playset seems to rock or sway too much. What’s wrong? Rocking is caused by uneven ground or obstructions such as rocks, roots, etc. under the ground rails.
Tools Required for Installation: (These are the tools that are generally required for assembly of our swing sets. These tools are not included in the swing set purchase.
Basic Setup Dimensions Place the set on level ground, not less than 6 ft [2 m] from any structure or obstruction such as a fence, garage, house, overhanging branches, laundry lines, or electrical wires. 72" Safe Play Zone 201 5/8" 98 1/4" 46 7/8" 81 15/16" 87 3/8" 22 1/4" Important Assembly Notes Safe play height: 8'-2 1/4" [2.5 m] Maximum fall height: 6'-3 5/16" [1.9 m] 1) While assembling unit, take time before and after each phase to make sure fort is level.
Parts Identification Wood Components (NOT TO SCALE) (2) E1 - FORT UPRIGHT - W101140 1 3/8"x3 3/8"x85 5/8" (36x86x2176) (2) E2 - FORT UPRIGHT - W101139 1 3/8"x3 3/8"x85 5/8" (36x86x2176) (2) M1 - GROUND BOARD - W101146 5/8"x3 3/8"x85 1/2" (16x86x2172) (1) H80 - GROUND BOARD - W100990 1"x3 3/8"x87 3/8" (24x86x2218) (2) E77 - ANGLE BRACE - W100991 1 3/8"x3 3/8"x74 3/8" (36x86x1890) (5) M2 - FLOOR BOARD - W101143 5/8"x3 3/8"x53 3/4" (16x86x1366) (1) E3 - TARP UPRIGHT - W101141 1 3/8"x3 3/8"x54 5/8" (36x86
Parts Identification Wood Components (NOT TO SCALE) (8) M4 - PICNIC TABLE BOARD - W101151 5/8"x3 3/8"x17 3/8" (16x86x442) (1) H2 - TARP UPRIGHT - W101144 1"x3 3/8"x20 1/4" (24x86x514) (2) M5 - LOWER WALL RAIL - W101154 5/8"x3 3/8"x13 1/2" (16x86x344) (1) H79 - END SUPPORT - W100992 1"x3 1/2"x42" (24x86x1072) (2) H1 - FLOOR BRACE - W101147 1"x3 3/8"x54 3/4" (24x86x1392) (4) M3 - WALL SLAT - W101148 5/8"x3 3/8"x38" (16x86x964) (2) K1 - TARP END CAP - W101145 5/8"x5 1/4"x22 1/4" (16x134x565) (1) G1 - TA
Parts Identification Hardware (4) AJ - BOLT HEX 5/16x1 1/4 - H100042 (2) AN - BOLT HEX 5/16x2-3/4 - H100047 (6) BG - T-NUT 5/16 - H100074 (2) Z - LAG SCREW WH 5/16x2 - H100027 (6) BF - T-NUT 3/8 - H100073 (6) CM - BOLT WH 5/16x1/2 - H100115 (10) H - BOLT WH 5/16x1 1/2 - H100010 (47) AC - WASHER LOCK EXT 8x19 - H100030 (53) AD - WASHER LOCK EXT 12x19 - H100031 (6) A - BOLT FA 3/8x1 1/2 - H100001 (4) J - BOLT WH 5/16x1 3/4 - H100011 (9) BC - SCREW PWH 8x3/4 - H100070 (20) K - BOLT WH 5/16x2 - H100012
Parts Identification Hardware (14) CH - SCREW TAPPING 14x1-1/2 - H100109 (8) CG - WASHER LOCK INT 8x15 - H100108 (4) BJ - SCREW TAPPING 14x1 - H100080 (10) CE - WASHER FLAT 9x18 - H100106 (12) BL - SCREW TAPPING 14x3/4 - H100083 (24) BW - SCREW PFH 8x3 - H100092 (50) BV - SCREW PFH 8x2 1/4 - H100091 (2) T-40 Torx Wrench - A100041 (4) BX - WASHER SPLIT 5/16 - H100095 (4) BS - SCREW PFH 8x1 3/4 - H100089 (35) BP - SCREW PFH 8x1 1/2 - H100086 (20) BQ - SCREW PFH 8x1 1/4 - H100087 (36) BR - SCREW PF
Parts Identification Accessories (NOT TO SCALE) (2) GL - PLATE 3 HOLE BLUE - A100149 (1) GZ - SLIDE RAIL 8' BLUE RIGHT - A100161 (1) HA - SLIDE RAIL 8' BLUE LEFT - A100162 (4) EA - HAND GRIP YELLOW PLASTIC - A100043 (3) GY - Climbing Rock Yellow Small - A100160 (1) EM - SLIDE BED 8' YELLOW - A100056 (3) GX - Climbing Rock Blue Small - A100159 (1) HC - BYD ID TAG (LARGE) 2011 WITH AGES - A100164 (1) GP - TARP .
4 Ft Swing Beam Phase 1 Phase Notes • Assemble with hardware as shown.
4 Ft Swing Beam Phase 2 Phase Notes • Assemble with hardware as shown.
4 Ft Swing Beam Phase 3 Phase Notes • Assemble with hardware as shown.
4 Ft Swing Beam Phase 4 Phase Notes • Assemble with hardware as shown.
Fort Assembly Phase 1 Hardware needed: Parts needed: • (12) D - NUT BARREL WH 5/16x7/8 - H100005 • (12) AD - WASHER LOCK EXT 12x19 - H100031 • (12) AC - WASHER LOCK EXT 8x19 - H100030 • (4) H - BOLT WH 5/16x1-1/2 - H100010 • (8) K - BOLT WH 5/16x2 - H100012 • (2) E1 - FORT UPRIGHT - W101140 • (2) E2 - FPRT UPRIGHT - W101139 • (2) H1 - FLOOR BRACE - W101147 • (2) M1 - GROUND BOARD - W101146 OREINT PRE-DRILLED HOLES IN THE NARROW EDGES OF 'E1' AND 'E2' UPRIGHTS TO THE OUTSIDE OF ASSEMBLY.
Fort Assembly Phase 2 Parts needed: Hardware needed: • (2) M72 - ROCK WALL SLAT - W100023 • (8) BV - SCREW PFH 8x2-1/4 - H100091 Phase Notes • Assemble with hardware as shown. Note: It is vital that the fort be level before and after each phase of assembly. ORIENT PRE-DRILLED HOLES IN THE NARROW EDGES OF 'E1' AND 'E2' UPRIGHTS TO THE OUTSIDE OF ASSEMBLY. E2 E2 BV E1 E1 M72 M72 Step 1: Attach 'M72' Rock Wall Slat to the edges of 'E1' & 'E2' Fort Uprights using hardware 'BV', as shown.
Fort Assembly Phase 3 Hardware needed: Parts needed: • (30) BR - SCREW PFH 8x1-1/8 - H100088 • (6) GW - L BRACKET BLUE 54 x 67 - H100158 • (12) BL - SCREW TAPPING 14x3/4 - H100083 • (5) M2 - FLOOR BOARD - W101143 • (3) N1 - FLOOR SUPPORT - W101152 Phase Notes • Assemble with hardware as shown. GW BL BR M2 N1 Step 1: Place Floor Supports 'N1' on Floor Boards 'M2' approximately 3 11/16" from both edges of 'M2' boards and attach the remaining 'N1' support, as shown.
Fort Assembly Phase 4 Parts needed: • (3) GE - MONKEY BAR RUNG - A100151 Hardware needed: • (6) CH - SCREW TAPPING 14x1-1/2 - H100109 Phase Notes • Assemble with hardware as shown. Note: It is vital that the fort be level before and after each phase of assembly. E1 CH GN Step 1: Secure Monkey Bar Rungs 'GN' to Uprights 'E1' with screws 'CH', as shown.
Fort Assembly Phase 5 Hardware needed: Parts needed: • (6) M71 - ROCK BOARD - W100022 • (1) M72 - ROCKWALL SLAT - W100023 • (3) GX - CLIMBING ROCK BLUE SMALL - A100159 • (3) GY - CLIMBING ROCK YELLOW SMALL - A100160 • (6) BF - T-NUT 3/8 - H100073 • (6) A - BOLT FA 3/8x1-1/2 - H100001 • (6) BR - SCREW TAPPING 8x1-1/8 - H100088 • (28) BV - SCREW PFH 8x2-1/4 - H100091 Phase Notes • Assemble with hardware as shown. Note: It is vital that the fort be level before and after each phase of assembly.
Fort Assembly Phase 6 Parts needed: Hardware needed: • (4) EA - YELLOW HAND GRIP - W100043 • (8) CE - WASHER FLAT 9x18 - H100106 • (8) CG - WASHER LOCK INT 8x15 - H100108 • (8) CH - SCREW TAPPING 14x1-1/2 - H100109 Phase Notes • Assemble with hardware as shown. To prevent board splitting, you must pre-drill each board before attaching with a 1/8" drill bit.
Fort Assembly Phase 7 Parts needed: Hardware needed: • (1) G1 - TARP SWING BEAM CROSS BRACE - W101153 • (1) G2 - TARP CROSS BRACE - W101142 • (1) H2 - TARP UPRIGHT - W101144 • (2) K1 - TARP END CAP - W101145 • (1) M72 - ROCK WALL SLAT - W100023 • (1) E3 - TARP UPRIGHT - W101141 • (2) D - NUT BARREL WH 5/16x7/8 - H100005 • (2) AD - WASHER LOCK EXT 12x19 - H100031 • (4) AC - WASHER LOCK EXT 8x19 - H100030 • (2) H - BOLT WH 5/16x1-1/2 - H100010 • (2) L - BOLT WH 5/16x2-1/4 - H100013 • (2) BG - T-NUT 5/16 -
Fort Assembly Phase 8 Parts needed: Hardware needed: • (2) GL - PLATE 3 HOLE BLUE - A100149 • (4) D - NUT BARREL WH 5/16x7/8 - H100005 • (4) AD - WASHER LOCK EXT 12x19 - H100031 • (4) AC - WASHER LOCK EXT 8x19 - H100030 • (4) BJ - SCREW TAPPING 14x1 - H100080 • (4) K - BOLT WH 5/16x2 - H100012 • (2) BV - SCREW PFH 8x2-1/4 - H100091 Phase Notes • Assemble with hardware as shown. • The Roof Assembly attaches differently on back of the Fort then it does on the front.
Fort Assembly Phase 9 Hardware needed: Parts needed: • (9) BC - SCREW PWH 8x3/4 - H100070 • (20) BQ - SCREW PFH 8x1-1/4 - H100087 • (4) M3 - WALL SLAT - W101148 • (2) M5 - LOWER WALL RAIL - W101154 • (1) GP - ROOF TARP - A100150 Phase Notes • Assemble with hardware as shown. G2 M3 M3 G1 BQ Step 1: Attach one end of each Wall Slats 'M3' to the inside of the Corss Beams 'G1' & 'G2' with Screws 'BQ' and attach the other end to the outside of Floor Supports 'H1' with Screws 'BQ', as shown.
Fort Assembly Phase 10 Hardware needed: Parts needed: • (10) D - NUT BARREL WH 5/16x7/8 - H100005 • (10) AD - WASHER LOCK EXT12x19 - H100031 • (10) AC - WASHER LOCK EXT8x19 - H100030 • (6) M - BOLT WH 5/16x2-1/2 - H100014 • (2) H - BOLT WH 5/16x1-1/2 - H100010 • (2) P - BOLT WH 5/16x3 - H100016 • (4) P1 - PICNIC TABLE UPRIGHT - W101155 • (2) P2 - PICNIC TABLE SEAT SUPPORT - W101156 • (2) P3 - PICNIC TABLE SUPPORT - A100157 • (1) N2 - SWING BLOCK SAFETY RAIL - W101149 Phase Notes • Assemble with hardware
Fort Assembly Phase 11 Hardware needed: Parts needed: • (6) D - NUT BARREL WH 5/16x7/8 - H100005 • (6) AD - WASHER LOCK EXT 12x19 - H100031 • (6) AC - WASHER LOCK EXT 8x19 - H100030 • (4) K - BOLT WH 5/16x2 - H100012 • (2) H - BOLT WH 5/16x1-1/2 - H100010 • (32) BP - SCREW PFH 8x1-1/2 - H100086 • (4) BS - SCREW PFH 8x1-3/4 - H100089 • (8) M4 - PICNIC TABLE BOARD - W101151 Phase Notes • Assemble with hardware as shown.
Swing Beam Attachment Phase 1 Hardware needed: Parts needed: • (4) BG - T-NUT 5/16 - H100074 • (4) BX - WASHER SPLIT 5/16 - H100095 • (4) CD - WASHER FLAT 8x27 - H100105 • (4) AJ - BOLT HEX 5/16x1-1/4 - H100042 • (4) CY - SCREW PFH 8x5/8 - H100128 • (1) SWING BEAM ASSEMBLY • (1) HC - BACKYARD DISCOVERY ID TAG - A100164 Phase Notes • Assemble with hardware as shown.
Slide Attachment Phase 1 Hardware needed: Parts needed: • (3) B - NUT BARREL WH 5/16x5/8 - H100004 • (3) AD - WASHER LOCK EXT 12x19 - H100031 • (3) CM - BOLT WH 5/16x1/2 - H100115 • (1) SLIDE ASSEMBLY Phase Notes • Assemble with hardware as shown. Step 1: Center the wave slide assembly in the opening opposite the swing beam assembly, as shown. Step 2: Using a drill with a 3/8" bit, drill a hole through the holes on the slide and through the fort floor.
Anchoring Instructions Phase 1 Parts needed: Hardware needed: • (6) KD - PLASTIC GROUND STAKE BROWN - A100179 • (2) FB - SWING SEAT ASSEMBLY - A100170 • (1) KF - PLASTIC TRAPEZE BAR ASSEMBLY YELLOW - A100109 • (6) BV - SCREW PFH 8x2-1/4 - H100091 Phase Notes • Assemble with hardware as shown. • Install the screw into the upright so that the tip of the screw does not stick through. Make sure you have enough wood to accommodate the screw before installing.
Limited Warranty This Limited Warranty by Backyard Discovery applies to products manufactured under the Backyard Discovery brand or its other brands including but not limited to Backyard Botanical, Adventure Playsets, and Leisure Time Products. Backyard Discovery warrants that this product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood, hardware, and accessories.