User’s Manual USB to 10/100 Base-TX Ethernet Adapter BF-310
CONTENT 1. Introduction----------------------------------------------------------------------------------2 2. Package Content--------------------------------------------------------------------------2 3. Product Features--------------------------------------------------------------------------2 4. System Requirements------------------------------------------------------------------2 5. Connecting for USB to 10/100 Base-TX Ethernet adapter-----------3 6.
1. Introduction The USB to 10/100 Base-TX Ethernet adapters performs good plug and play connection of PC peripherals “Out-side the box” and mark a significant advance in desktop cable management. Using the USB Ethernet 10/100 adapter you can simplify your PC network connections in the home, office and on the road. The Universal Serial Bus was designed to replace the current serial, parallel and other port types used on a PC with a single universal interface.
5. Connecting for USB to 10/100 Base-TX Ethernet adapter To connect the USB to 10/100 Base-TX Ethernet adapter to local network, please follow the below steps: 5.1 Prepare a straight-through twisted-pair cable, maximum length 100 meters 5.2 Use category 3, 4, 5 cables for connection to 10Mbps Ethernet 5.3 Use category 5 cable for connection to 100Mbps fast Ethernet 5.4 Connection one end of the cable to the RJ-45 port on the USB Ethernet 10/100 adapter 5.
6.1.4 Select “Specify a location” and type D:\DRIVER\BF-310\WINDOWS (D: represents CD-ROM) in the dialog box, then click “Next” 6.1.5 Windows® will search the driver for this device. Make sure the driver that Windows® found is “D:\DRIVER\BF-310\WINDOWS\BAFO.INF” then click “Next”. 6.1.6 After Windows® finish copying “BAFO.INF”; it wills pop-up a dialog box asking “Windows 98 Second Edition CD-ROM”. Take driver CD off and put Windows 98 CD in. Then Click “OK” to continue.
.1.7 Click “Finish” to complete the installation of “BAFO-series USB NIC” 6.1.8 To finish setting up new hardware, click on “Yes” to restart your computer. 6.1.15 After Windows ® installed the entire driver; you have to check “My Computer”-“Control Panel”-“System”-”Device Manager” to make sure the driver has already installed. In the “Network adapters” it will show “BAFO-series USB NIC”.
6.2 Windows® ME installation 6.2.1 Connect the USB port of USB to 10/100 Ethernet adapter to PC with USB cable. 6.2.2 The “Add New Hardware Wizard” dialog box will appears as below. 6.2.3 Choose “Automatic search for a better driver (Recommended)” and click on “Next “to continue. 6.2.4 Click on “Finish” to end this installation. 6.2.5 Click on “Yes” to restart your computer. 6.2.6 You should check “My Computer”-“Control Panel”-“System”-”Device Manager” to make sure the driver has already installed.
USB to 10/100 Base-TX Ethernet adapter User’s Manual 7
6.3 Windows® 2000 installation 6.3.1 Connect the USB port of “USB to 10/100 Ethernet adapter” to PC with USB cable. 6.3.2 The “Add New Hardware Wizard” dialog box will appears as below. 6.3.3 Choose “Search for a suitable driver for my device (Recommended)” then click “Next”. 6.3.4 Choose “CD-ROM drives” and “Specify a location” then click on “Next” to continue.
6.3.5 Type D:\DRIVER\BF-310\WINDOWS (D: represents CD-ROM) in the dialog box, and then click “OK” to continue. 6.3.6 Windows® will search the driver for this device. Make sure the driver that Windows® find is “d:\driver\bf-310\windows\bafo.inf” then click “next” to continue. 6.3.7 While Windows ® install the driver, in the same time it will pop up a “Digital Signature not found” dialog box. Click “Yes” to continue. 6.3.8 Click “Finish” to end the installation of “Bafo-series USB NIC”.
6.3.9 Please check “My Computer”-“Control Panel”-“System”“Hardware”-“Device Manager” to make sure the driver has already installed. Then, in the “Network adapters” it will show “BAFO-series USB NIC”.
6.4 Windows® XP installation 6.4.1 Connect the USB port of USB to 10/100 Ethernet adapter to PC with USB cable. 6.4.2 The “Add New Hardware Wizard” dialog box will appears as below. Select “Install the software automatically (Recommended)” and then click on “Next” to continue. 6.4.3 Windows® will show a warning message about “software not pass Windows® logo”, click on “Continue anyway” to continue. 6.4.4 Click on “Finish” to end this installation.
6.4.5 Please let Mouse point to “My Computer” click on right key -“Properties”-“Hardware”-”Device Manager” to make sure the driver has already installed. 6.4.6 Then, in the “Network adapters” it will show “BAFO-series USB NIC”. 7. FAQ Q: When USB to 10/100 Ethernet adapter be plugged into PC USB Port, but “Add New Hardware Wizard” does not show up. What should I do? A: Check if RJ-45 plug are well plugging into “USB to 10/100 Ethernet adapter” and network Hub or Switch. 8.
§ Reorient or relocate the receiving antenna. § Increase the separation between the device and receiver. § Connect the computer into an outlet on a circuit different from that to which the receiver is connected. § Consult the dealer or an experienced radio/TV technician for help. Consult the dealer or an experienced radio/TV technician for help. 10.Technical Support If you encounter any technical problem, please contact us through: Taiwan First Line Electronics Corp. No.
