Installation Guide

Follow steps # 1 thru # 5 in the Passage
Latchset Installation section before
proceeding to step # 2.
3. Install the outside
adaptor. Insert the flat
head screws through
the inside adaptor and
into the outside adaptor.
Do not fully tighten at
this time.
2. Install the inside
adaptor. This adaptor
will have thru-holes for
the flat head screws to
fit into.
1. Locate the position
for hole in door. If not
used with a double
door, the hole location
should be approx. 40”
from floor. Drill a 1/2”
hole through door.
2. Place backplate on door so that
the flat surface is toward the floor.
The flat surface should be parallel
to the floor and perpendicular to
the door edge. A builder’s square
should be used for best results.
Using the backplate as a template,
mark center locations for (3) screw
holes. Remove backplate and
pre-drill (3) holes for screws ½”
deep using a 1/16” drill bit. Install
backplate with (3) flat head screws
provided. Repeat for both sides of
door. IMPORTANT: Before drilling
1/16” holes ensure the spindle can
insert into one backplate and out
of the other at marked position.
1. With backset marking
facing up, grasp the
faceplate and rotate to
assure bevel side of
latchbolt faces jamb.
Slide the latch into the
door as shown and
secure with (2) #8-3/4”
combination screws
4. Insert the spindle
into the latch with the
ends protruding from
both adaptors. Slide
the alignment bushings
onto the spindle ends
and into the adaptors.
Tighten the screws and
remove the alignment
bushings.
5. Remove the spindle.
Attach the roses by
screwing the threaded re-
tainer onto the adaptors.
Orient the rose as desired
and securely tighten by
using the spanner tool.
For 5” & 10” roses,
ensure rose is parallel
with door edge and
drill 3/32” x 1/2“ deep
pilot holes at marked
locations. Install #8 oval
head screws into door.
7. Slide a nylon washer
onto the base of both
knobs or levers. Slide
the spindle with the
previously attached
knob or lever into the
latch with the set screw
pointed down and
toward the hinges of the
door. Secure the other
knob or lever to the
exposed spindle end.”
FOLLOw STEPS
#5 THRU #7 OF
PASSAGE
LATCHSET
INSTALLATION
FOR ATTACHING THE
ROSE, SPINDLE &
KNOb OR LEVER.
1a. With backset marking facing up, grasp
the faceplate and rotate to assure bevel side of
latchbolt faces jamb. From the side of the latch
that will be inside the room, push in the privacy
lug. On the other side of the lug install either
an oval spacer or round spacer depending on
lug shape with provided screw. The side with
the spacer should be facing outside of the room
after install with the backset marking facing up.
1b. If the privacy latch-
set is being installed
on a 1-3/4” thick door
thread the privacy but-
ton extension onto the
privacy button before
proceeding to step # 2.
2. Insert the privacy
pin into the hole on
the inside rosette and
thread into the latch.
3. Insert the spindle
into the rose so the
end of the spindle with
stops is on the same
side of the door as the
privacy button. The
spindle V groove will
be positioned down and
towards the hinges of
the door.
4. Slide nylon washer
onto base of knob or
lever. Install knob or
lever onto spindle on
the outside. Secure
with set screw pointed
down and toward the
hinges of the door.
5. Slide nylon washer
onto base of other knob
or lever. Install knob or
lever onto spindle on
the inside. Secure with
set screw pointed down
and towards the hinges
of the door.
PRIVACY LATCHSET INSTALLATION
FULL DUMMY INSTALLATION
PASSAGE LATCHSET INSTALLATION
SPANNER TOOL
RETAINER
SPINDLE
ALIGNMENT
BUSHING
ALIGNMENT
BUSHING
PRIVACY PIN
EXTENSION
PRIVACY PIN
BACKPLATE
ROSE
#8 X 3/4” OVAL
HEAD SCREWS
(*See note.)
FLAT HEAD
SCREWS
RETAINER
SET SCREW
KNOB
BACKPLATE
SPINDLE
#8 SCREWS
STOP
BACKSET DIMENSION
(2-3/8” OR 2-3/4”)
*Note: #8 Oval Head Screws are not required
on 3” rose styles.
©2011 Baldwin Hardware Corporation, Lake Forest, CA, 92610
MARK LOCATION
OF HOLES
NOTCHES
HORIZONTAL LINE
Consumer Help Line 1-800-566-1986
wARRANTY INFORMATION
Limited Lifetime Mechanical warranty – Baldwin warrants
that each Baldwin product shall be free from mechanical defects at
the time of delivery and for the lifetime of the product or as long as
you own your home.
Limited Lifetime Finish
™
warranty – The Baldwin Lifetime
Finish
™
uses advanced finishing technology (physical vapor
deposition) to create a finish highly resistant to the effects of
weather and normal wear and tear. The Limited Lifetime Finish
Warranty on Lifetime Finish
™
products covers the original
purchaser for as long as you own your home.
Limited Finish warranty – The finish on Baldwin products
(excluding Lifetime Finish and living finish products) is protected by
a durable topcoat designed to maintain the beauty and quality of the
Baldwin product. The Baldwin Limited Finish Warranty covers the
original purchaser for five years from date of purchase for interior use
and one year for exterior use.
Living Finishes – Due to the nature of Baldwin living finish
products, they will wear over time and may already have begun the
process before reaching your home. No finish warranty is offered
on living finish products, which are designed to age and improve
over time. Living finishes include raw brass, oil rubbed bronze,
stainless steel, and other non-lacquered or non-PVD finishes.
Refer to www.baldwinhardware.com for a complete warranty statement.
6. Insert the
spindle into a
knob or lever.
Align scribed mark
with correct door
thickness and
secure with set
screw.
1-3/4”
1-3/8”
SET SCREW
SPINDLE
or
BACKSET MARKING
INSIDE
ADAPTER
a
OUTSIDE
ADAPTER
a
a
a
BACKSET MARKING MUST BE FACING UP
DOOR EDGE
DOOR EDGE
a
FACE PLATE