Installation Guide

ManualsBrandsBALDWIN ManualsKeyed Entry Door Handlesets85360.150.ENTR

Installation Instructions

ENGLISH

Congratulations!

With your purchase of this Premium Entrance Set, you’re among a group

of discerning individuals who know the intrinsic value of selecting the

finest—Baldwin.

Our step-by-step installation instructions will help guide you through your

project quickly and easily.

Before you begin your installation, read and understand the installation

instructions and marking templates. If you have any questions, please

do not hesitate to contact our Baldwin Consumer Help Line at

1-800-566-1986. We’re here to help! We thank you for your purchase

and wish you the fullest enjoyment of your Baldwin product.

Care and Maintenance

WARNING: Do not attempt to clean your hardware with any type of abra-

sive cleaners, solvents, or chemicals. These types of cleaning agents may

mar the finish. A damp cloth is all that is necessary to wipe clean.

Note: Finish Number 102, Oil-Rubbed Bronze, can be cleaned with light

machine oil and wiped with a dry cloth.

©Baldwin Hardware Corporation - A Masco Company

P.O. Box 15048, Reading, PA 19612

Remember Baldwin

With the completion of your project, remember that Baldwin quality hard-

ware and giftware products are available for all your decorating and

remodeling needs. Matching entrance sets for exterior doors, beautiful

bath accessories, and a complete selection of cabinet and door-enhancing

hardware are all available from your Baldwin retailer.

To request a product brochure or the name of a retailer near you,

call 1-800-566-1986.

Baldwin offers a vast array of exceptional solid brass products to elegantly

enhance all areas of the home. Each collection features a wide variety of

beautiful, high-fashion finishes. From locking products to lighting and

bath accessories, Baldwin provides the discriminating decorator with

numerous options to accent and complement the home’s ambience with

distinction, taste, and fine detail.

Complimentary Baldwin

Security Test and Rebate Offer

Be assured that your home is safe and secure with Baldwin’s Security Test.

To get yours free, download it at www.baldwinhard-

ware.com/security and receive a special online

rebate offer. Or write to Baldwin Hardware

Corporation, P.O. Box 15048, Reading, PA

19612.

Consumer Help Line

1-800-566-1986

Hours: 6 a.m. to Midnight C.S.T.—7 days a week

If you have trouble installing your Baldwin product, feel free to call our

toll-free Consumer Help Line.

www.baldwinstyleguide.com

www.baldwinhardware.com

Premium Entrance Set

EMERGENCY EXIT FUNCTION

5360

Blakely

5350

Manchester

PK.EGENTR

8/20/02

5355

Stonegate

Summary of content (13 pages)

PAGE 1
Congratulations! PK.EGENTR With your purchase of this Premium Entrance Set, you’re among a group of discerning individuals who know the intrinsic value of selecting the finest—Baldwin. Our step-by-step installation instructions will help guide you through your project quickly and easily. Before you begin your installation, read and understand the installation instructions and marking templates. If you have any questions, please do not hesitate to contact our Baldwin Consumer Help Line at 1-800-566-1986.
PAGE 2
Required Tools ⁄8" Wood Drill Bit Protective Eyewear Phillips Screwdriver Flat Head Screwdriver Tape Measure Electric Drill 21⁄8" Dia.
PAGE 3
1 Before You Begin • Remove and discard all materials and screw(s) used for packing your Premium Entrance Set. Verify that you have all parts pictured on exploded view section of instructions. • Check the thickness of the door. This lockset works on doors 13⁄4" thick only. For doors greater than 13⁄4" up to 21⁄4" thick, contact our Consumer Help Line at 1-800-566-1986. The conversion kit part number for this item is 5399.XXX.C; please specify the finish of your product.
PAGE 4
Handleset Installation Fasteners Strikeplate Installation Fasteners Set Screw (2) #8-32 x 1⁄4" Screws (2 or 4) #6-32 x 7⁄16" Oval Head Screws (4) #8 x 3⁄4" Combination Screws (2) #8 x 3⁄4" Wood Screws (1) #10-32 x 21⁄2" Flat Head Screw (2) #10-32 x 17⁄8" Flat Head Screws (2) #10-32 x 11⁄4" Flat Head Screws (2) 3" Reinforcing Screws (2) #8 x 3⁄4" Combination Screws If you have any trouble installing your Baldwin product, feel free to call our toll-free consumer help line at 1-800-566-1986.
PAGE 5
Door Hole Template Door Frame Template If you have any trouble installing your Baldwin product, feel free to call our toll-free consumer help line at 1-800-566-1986. Hours: 6 a.m. – midnight (east coast standard), 7 days a week. 5.
PAGE 6
2 Door Preparation (If Needed) door stop B hole template low side of bevel A top of door 1 Pull door toward you to check if it’s level. Observe contact of door to jam and make sure it’s level. Adjust if necessary. 2 (Aerial View) To ensure proper alignment, only use hole template on side facing doorstop. Helpful Hint: Some doors have a beveled edge with bevel facing doorstop. 3 Fold hole template along door edge with center of bottom hole (A), the 21⁄8" dia. hole, 38" from floor.
PAGE 7
2 Door Preparation (If Needed) cont. Masking tape 1" 3 ⁄2"or 3 ⁄8" 1 B A 6 Complete drilling holes (A, B) from opposite side of door. 7 C C D D 7 Very carefully drill (C, D) holes into door edge exactly at pencil marks. 31⁄2" deep for a 23⁄8" backset 37⁄8" deep for a 23⁄4" backset Helpful Hint: Mark edge depth of drilling with masking tape. E 8 Very carefully drill (E) ⁄ " 5 16 hole into door exactly at pencil mark. 9 Insert latch into hole (D).
PAGE 8
3 Handleset Installation Top inside 1 Determine your backset, which is the distance from the edge of door to center of hole. Your lockset is shipped with a 23⁄8" backset (most common). Adjust for a 23⁄4" backset door only. 2 For a 2 ⁄ " backset, grasp 3 4 body and twist faceplate 180º until it stops. Angled side of bolt should face outside. Follow same procedure for deadbolt. Note: See deadbolt orientation during installation step 4. 3 Insert latch with angled side of bolt facing outside.
PAGE 9
3 Handleset Installation (cont.) Spindle V groove on bottom toward hinges E inside inside 6 Attach handle by inserting the #10-32 x 21⁄2" flat head screw on inside of door through screw cover backplate and the lower hole (E). Leave screw loose for adjustment. Note: Go to door preparation if you do not have a lower hole (E). 7 From inside of door, slide alignment fitting between post and around latch. inside 8 Measure the thickness of your door.
PAGE 10
3 Handleset Installation (cont.) Door edge Mounting screw hole is covered Lever Version Tailpiece vertical inside 11 Rotate deadbolt cam toward door edge using a flat head screwdriver. This will cover the mounting screw hole that is closest to door edge. inside 12 Keeping tailpiece vertical, insert cylinder tailpiece through outside handle assembly, deadbolt, and emergency exit cartridge.
PAGE 11
Installation 4 Strikeplate IMPORTANT! You must install Baldwin strikeplate or your warranty is void. 5/32" inside 1 If weather stripping is not installed, you must install weather stripping prior to strikeplate installation. Mark center of deadbolt with chalk, grease pencil, or lipstick. Shut door and lock deadbolt to mark center point on doorframe. 2 On doorframe, align strike hole template with center point. Mark holes for center of latch bolt and outer corners of both strikes with pencil.
PAGE 12
Installation (cont.) 4 Strikeplate IMPORTANT! You must install Baldwin strikeplate or your warranty is void. outside inside 6 For Deadbolt inside Strikeplate: Insert dustbox into hole, add reinforcing strike, and secure with 3" reinforcing screws (outside holes) and #8 x 3 ⁄4" combination screws (inside holes). Helpful Hint: When installing wood screws it is recommended to put beeswax or soap on screw threads to improve installation.
PAGE 13
Troubleshooting Guide If parts are missing do not return product. Please call Baldwin's Consumer Help Line at 1-800-566-1986 and we will quickly send the parts to you. Problem Can’t extend deadbolt unless key is in cylinder. Can’t remove key with deadbolt in extended position. Screws are all tight but the hardware is not firmly attached to the door. Knob or lever keeps coming off the spindle. Door is difficult to latch or will not stay closed unless deadbolt is extended.