Installation Guide

ManualsBrandsBaldwin ManualsDoor KnobsReserve Ellipse Venetian Bronze Passage Knob with Traditional Round Rose

If not already installed, insert

the half round spindle

into exterior chassis.

After the completion of Step 1, install the longer half round spindle

supplied in the kit. Install the privacy pin on privacy products only. Proceed

to Step 3 and install with longer screws. During Step 5, install strike

supplied in the kit.

Privacy/Passage Knob and Lever Installation Instructions

Fits 1-3/8" (40 mm) up to 2" (51 mm) doors

(Thick door service kits for

2" (51 mm) up to 2-1/2" (64 mm) doors

available through customer service)

Place knob or lever onto chassis and turn set screw clockwise to secure.

Repeat for knob or lever on the other side.

The set screws are pre-installed.

They do not need to be removed

prior to knob/lever installation.

Adjust tang as needed.

THICK DOOR KIT INSTALLATION INSTRUCTIONS

(AVAILABLE SEPARATELY)

Supports 2" (51 mm) up to 2-1/2" (64 mm) doors

TEMPLATE

1-3/8"

(35 mm)

1-3/4"

(44 mm)

(51 mm)

2-1/4"

(57 mm)

2-1/2"

(64 mm)

Centerline

Ligne médiane

Linea central

Fold

Doble

Plier

2-3/8" 60mm

2-3/4" 70mm

47038 / 01

Door Preparation

If your door requires drilling, use the supplied template below with the door preparation

instructions available at www.baldwinhardware.com

Note: For privacy knob or lever, make

sure the toggle is in the unlocked

position closest to the latch.

www.baldwinhardware.com • Customer Service 1.800.437.7448

Please note: Product

illustrations may differ

from your product.

Installation is the same.

If backset of door measured

2-3/4" (70mm), adjust latch shown

by grasping the spring pin and

moving it to the 2-3/4" slot.

Save the bedroom/bathroom emergency unlock tool for future use.

For privacy function only.

1. Adjust and install latch 4. Install knob/lever

5. Install strike

Measure your door backset as shown.

For Drive In Latch

LATCH ASSEMBLY AND INSTALLATION

Install with 1/2" screws.

Snap on collar.

Drive in with hammer.

For Square Corner and Round Corner

Snap together front and back plate.

Make sure the slant of latch bolt faces in the direction that the door closes.

2. Install spindle

Push and hold in latch bolt, align curve of half round spindle

with latch, and install exterior chassis.

3. Install chassis

exterior chassis

interior chassis

Align curve of half

round spindle with

interior chassis and

install with screws.

exterior chassis

privacy pin

(for privacy function only)

longer half

round spindle

The drilling template must be printed to scale

to ensure correct hole placement. To conﬁrm

correct print scale, the square below must

measure exactly 1" by 1" (25mm x 25mm).

25mm

Measure

after printing.

Summary of content (2 pages)

PAGE 1
Privacy/Passage Knob and Lever Installation Instructions Fits 1-3/8" (40 mm) up to 2" (51 mm) doors (Thick door service kits for 2" (51 mm) up to 2-1/2" (64 mm) doors available through customer service) www.baldwinhardware.com • Customer Service 1.800.437.7448 1. Adjust and install latch 4. Install knob/lever Measure your door backset as shown. Place knob or lever onto chassis and turn set screw clockwise to secure. Repeat for knob or lever on the other side.
PAGE 2
Instructions d’installation de la poignée de sûreté ou de passage et du retour Instrucciones de instalación para la perilla o manija de privacidad S’ajuste sur des portes de 1-3/8" (35 mm) jusqu’à 2" (51 mm) Para puertas de 1-3/8" (35 mm) a 2" (51 mm) (On peut se procurer des trousses de service pour portes d’une épaisseur de 2" (51 mm) à 2-1/2" (64 mm) auprès du service à la clientèle) (El servicio al cliente tiene juegos de reparación para puertas gruesas de 2" (51 mm) a 2-1/2" (64 mm) www.