Installation Guide

ManualsBrandsBali Cut-to-Size ManualsBlindsRustic Cream 3.5 in. PVC Louver Set - 62 in. L (9-Pack)

PARTS LIST

1. Headrail

2. Louvers

3. Wall brackets with

mounting clip

4. Mounting screws

5. Valance clip

6. Channel panel valance

7. Valance corner

8. S-shape valance corner

OUTSIDE STEP 1: Measure louver length and add 2" to your measurement.

Starting from the floor or window sill, measure and mark this distance at three

points across the top of the window. The top of the brackets will be placed at

this height.

1. Louver Length

2. Floor or Sill

OUTSIDE STEP 2: Center headrail over your window. To mark location of

brackets, make 2" long marks about 4" from each end of the headrail. For wider

windows, additional support brackets are supplied and should be spaced evenly

between the two end brackets.

OUTSIDE STEP 3: Hold brackets up to 2" long marks and mark mounting holes

on the wall. Loosen mounting clip screw and turn ¼ to twist clip out of your

way. Drill holes at mounting hole marks and screw brackets into place using two

screws per bracket. (Use

⁄

" drill bit if using wall anchor or

⁄

" if using screws

only.)

OUTSIDE STEP 5: Twist all mounting clips back to original position and tighten

all screws. Snap headrail into bracket clips as shown.

Note: You will need at least 1½" between the back of the headrail and the wall,

window or any obstructions such as window cranks or molding.

To adjust, loosen adjusting screw and slide clip out to get enough clearance,

then retighten.

1. Adjusting Screw

Go to “Installing Valance.”

VERTICAL KIT INSTALLATION INSTRUCTIONS

OUTSIDE MOUNT

FIRST: Choose how you will mount your blind.

OUTSIDE or INSIDE the window or door frame.

OUTSIDE STEP 4: Snap valance clips onto headrail before snapping headrail

into mounting brackets.

INSIDE STEP 3:

Hold each clip up to the ceiling or window frame so the front of the clip lines up

with your mark. Mark the holes in each clip.

Drill holes at these marks and screw clips into place using one screw per clip.

Additional mounting clips are supplied for wider windows and should be spaced

evenly between the two end clips.

Note: You will need at least 1

⁄2" between the back of the headrail and the wall,

window or any obstructions such as window cranks or molding.

INSIDE STEP 4:

Snap valance clips onto headrail before snapping headrail into mounting brack-

ets.

Insert headrail as shown.

Go to “Installing Valance.”

INSIDE MOUNT

INSIDE STEP 1: To mark location of mounting clips, place a 1" long mark on the

inside of the window frame about 4" from the corners and 2

⁄4" from the window.

1. Back of Headrail

2. At least 1½" gap for 3½" louvers (can be more)

At least 1" gap for 2½" louvers (can be no more)

3. Wall or Window

INSIDE STEP 2: Mounting clips may come attached to mounting brackets, but

brackets are not used for this mounting method. Loosen and remove the screw

on the bottom of the bracket. Discard brackets and adjusting screws.

1. Bracket 2. Clip

Snap

5 cm

10 cm

Snap

Clip Screw

Back of

headrail

At least 1 1/2" clearance (Can be m

NOTE: Window size blinds require 1

Wall or window

gap

78025-00 (2/10)

1 1/2"

MINIMUM

USTING

REW

3.81 cm

LOUVER

LENGTH

WALL

FLOOR

OR SILL

5.08 cm

Summary of content (5 pages)

PAGE 1
VERTICAL KIT INSTALLATION INSTRUCTIONS PARTS LIST 1. Headrail 2. Louvers 3. Wall brackets with mounting clip 4. Mounting screws 5. Valance clip 6. Channel panel valance 7. Valance corner 8. S-shape valance corner 3 4 Note: You will need at least 1½" between the back of the headrail and the wall, window or any obstructions such as window cranks or molding. To adjust, loosen adjusting screw and slide clip out to get enough clearance, then retighten. 1. Adjusting Screw JUSTING 1.
PAGE 2
INSTALLING VALANCE Springs Window Fashions Three-year Warranty Slide louver into channel panel and returns (see below for s-shaped louvers). Attach channel panel to valance clips. For inside mount, go to “Installing Louvers.” For outside mount, attach valance corner to channel panel return. Attach valance corner with returns to valance. 1. Channel panel valance 2. Valance clip 2 1 3. Valance return 4.
PAGE 3
PARA EXTERIOR – PASO 5: Vuelva a girar todos los sujetadores a su posición original y ajuste todos los tornillos. Enganche el riel superior en los sujetadores del soporte como se muestra en la figura. INSTRUCCIONES DE INSTALACIÓN DEL JUEGO VERTICAL LISTA DE PIEZAS 1. Riel principal 2. Celosías 3. Soportes para pared con sujetador 4. Tornillos de instalación 5. Sujetador de cenefa 6. Cenefa de panel acanalado 7. Rincón de cenefa 8.
PAGE 4
INSTALACIÓN DE CENEFA Deslice la persiana en el panel y los retornos de canal (vea más abajo las persianas con forma de "S"). Fije el panel de canal a las abrazaderas para cenefa. Para instalación empotrada, consulte “Instalación de persianas fijas”. Para instalación exterior, fije la cenefa de esquina al retorno del panel de canal. Fije la cenefa de esquina con retornos a la cenefa. 1. 2. 3. 4.
PAGE 5
EXTÉRIEUR, ÉTAPE 5: Remettez toutes les attaches de montage à leur position originale et serrez toutes les vis. Enclenchez la tringle porteuse dans les attaches de support comme il est illustré. Remarque: Il vous faudra au moins 4 cm d’espace entre le dos de la tringle et le mur, la fenêtre ou tout autre obstacle telle que poignée de fenêtre ou moulure. Pour ajuster, desserrez la vis de réglage et faites glisser l’attache afin d’obtenir l’espace de dégagement nécessaire, puis resserrez. 1.