Owner’s Manual & Assembly Instructions Do Not Discard, Retain for Future Reference SunSetter OASIS® Freestanding Awning WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PERSONAL INJURY! For Technical support visit us at http://ownerscorner.sunsetter.com, e-mail at contactus@sunsetter.
READ ME FIRST Congratulations! You have purchased the SunSetter OASIS Freestanding Lateral Arm Awning which will provide you and your family with many years of enjoyment outdoors. Before you begin assembly, take a moment to familiarize yourself with the Awning and its Owner’s Manual. Please check to ensure all of the parts listed have been included with your Awning and that you have the correct color Fabric.
TABLE OF CONTENTS READ ME FIRST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii Parts Supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts Supplied Square Bar Upright Qty 2 Corner Braces Qty 4 Crank Wand Qty 1 3/8” x 21/2” Hex Bolt Qty 10 Leg Assembly Qty 2 Lock Nut Qty 12 Oasis Square Bar Plug, Black Plastic End Cap Qty 4 Rubber Pad Qty 8 3/8” Flat Washer Qty 20 Parts Supplied - Motorized Models Only Wall Mount Kit for Remote Transmitter Qty 1 Multi-Channel Remote Transmitter Qty 1 (spare) Battery CR2430 Qty 1 Cord Cover 74” Long Qty 1 Velcro Straps Qty 4 iv
SunSetter Oasis Freestanding Awning Assembly and Operating Instructions WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS CAN RESULT IN PERSONAL INJURY! PLEASE READ THESE INSTRUCTIONS IN ITS ENTIRETY BEFORE ATTEMPTING TO COMPLETE THIS PROCESS. WARNING: DO NOT REMOVE THE PLASTIC SAFETY SLEEVES FROM THE LATERAL ARMS UNTIL INSTRUCTED TO DO SO. CAUTION: Do not remove the Red Foam Packing located at the middle of the Oasis Awning Assembly until instructed to do so. 1.
2. Position two chairs approximately 8 feet apart. Carefully remove the Awning assembly from the cardboard shipping tube and separate the Corner Braces, Hand Crank Wand, Cover (if purchased) and Fasteners from the Awning. Lay the Awning Assembly across the chairs with the Horizontal Square Bar facing towards the front of the chairs, being careful not to damage the Fabric. See Figure 2.
. Repeat Steps 5 and 6 for the other end of the Awning Assembly. MOTORIZED MODELS ONLY: remove the Nylon Cable Tie that is securing the Electrical Cord to the Awning Top Bracket. 8. Locate the two (2) Square Bar Uprights packaged in the cardboard box. See Figure 5. 9. Orient one of the Square Bar Uprights so that the end of the Bar with the two holes that are approximately 3 inches apart is pointing toward the Awning Assembly. See Figure 5.
Complete the Leg Assembly 16. Orient one of the Leg Assemblies as shown in Figure 6. 17. Push the Leg Assembly onto the Square Bar Upright, making sure that the Bolt Holes in the Leg Assembly and Square Bar Upright are properly aligned. See Figure 6a. Figure 6a Bolt Holes 18. Using two sets of Hardware (1 Nut, 1 Bolt and 2 Washers) secure the Leg Assembly to the Square Bar Upright and securely tighten Bolts. 19. Repeat Steps 16 thru 18 for the other end of the Awning Assembly.
Upright the Awning onto the Leg Assemblies WARNING: THE FOLLOWING PROCEDURE SHOULD BE PERFORMED BY FOUR PEOPLE! 21. One person should be positioned at each Leg Assembly to prevent the Awning from sliding as the unit is placed in the upright position. See Figure 8. Figure 8 22. One person should be positioned at each end of the Awning Assembly, and be able to support and lift the weight of that end of the Awning. See Figure 8. 23.
Test for Proper Operation Motorized Awnings Only Note: When opening the Awning for the first time, the Motor will begin to open, quickly reverse direction closing all the way, then continue to open. This is a standard operation of the Motor after it has been without power for more than two (2) minutes. Figure 13 Note: The Open and Close Stop Position Limits on the Awning Motor were set and tested at the SunSetter factory prior to shipment. 28.
PROTECTING THE SUNSETTER FRAME Your SunSetter Awning contains extruded and die cast aluminum components. These aluminum parts are powder-coated for long lasting beauty. We have included a bottle of color-matched touch-up paint with your Awning in the event that some area of the painted surface gets scratched during installation. Please use as needed. General Care and Maintenance CAUTION: Prior to Operating the Awning, Be Sure That No Objects or Persons Can Come in Contact With it as it Opens and Closes.
Care and Maintenance - SunSetter Woven Acrylic Fabrics SunSetter woven acrylic Fabrics are made of 100% solution-dyed acrylic fiber and have a special finish which delays the formation and accumulation of dirt. To preserve this finish, cleaning of the Fabric must include the following. Standard Maintenance • Thoroughly remove the dust from the dry Awning Fabric by vacuum cleaning, gently beating or brushing. • Then clean with a prolonged spraying of lukewarm water and a mild soap while gently brushing.
Care and Maintenance of Your Electric Motor and Remote Transmitter WARNING: ANY PERMANENT WIRING OF THE AWNING MUST BE PERFORMED BY A LICENSED ELECTRICIAN PER YOUR LOCAL ELECTRICAL CODES. FAILURE TO DO SO COULD RESULT IN PERSONAL INJURY. Changing the Battery in Your Remote Transmitter Please note that you might have to replace the battery (3V Lithium CR2430) after 3 years, or if the Remote Transmitter stops working.
Protective Cover - OASIS Freestanding Awning Installation Instructions - ‘Helper Needed’ Tools Needed: Step Ladder (2) Parts Supplied: Cover, Bungee Cords (7 for 12ft model, 9 for 16ft model) WARNING: FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PERSONAL INJURY. Make sure that your Oasis Awning is in the fully closed position. Remove the Protective Cover from its packaging. Orient the Cover so that the sewn hem is facing down.
TROUBLESHOOTING Problem with Appearance Solution Fabric wrinkles when the Awning is opened/closed The Awning Fabric has a hem along each side; some wrinkling is a characteristic of the extra thickness along those edges. This wrinkling may be more noticeable when retracted and after prolonged periods when the Awning is not used. This condition is normal. Lateral Arms (elbows) are not even when Awning is retracted Each Lateral Arm is individually connected to the Awning assembly Top Brackets.
TROUBLESHOOTING - Continued Problem with Motor or Gear Assembly Solution Can I “hard-wire” the Awning Motor into my home? SunSetter cannot be responsible for any changes in electrical configuration of the Motorized Awning. Have your electrician contact Somfy (motor manufacturer) directly via their website www.somfysystems.com. Note: Some maintenance procedures such as resetting communication between the Remote Transmitter and Awning require power to be interrupted.
APPENDIX A ADJUSTING THE OPEN AND CLOSE STOP LIMITS FOR THE SUNSETTER MOTORIZED AWNING TO CHANGE THE OPEN LIMIT: 1. Open the Awning to its current Open position and let it stop on its own. Close my/Stop Open Channel Indicator Lights Channel Selector Button 2. Press and Hold the OPEN and CLOSE buttons simultaneously until the Awning moves a little bit, or jogs back and forth, then release the buttons. 3.
• • • APPENDIX B Resetting Remote Communication and Reprogramming the Motor This procedure describes the actions needed to reset the communication between the Motor and the primary Remote Transmitter used to control your Motorized Awning. This procedure programs the Awning Motor to accept commands from one primary Remote Transmitter. This procedure overwrites the factory set Open and Closed positions with new Open and Closed positions.
5-Year Limited Manufacturer’s Warranty For the SunSetter OASIS and Accessories A. WHO GIVES THIS WARRANTY? SunSetter Products, 184 Charles Street, Malden, MA 02148. B. WHO IS ENTITLED TO THIS WARRANTY? This Warranty applies only to the original purchaser who paid for the product and may not be assigned or transferred to subsequent owners. This Warranty applies only to products purchased and located in the US. C.
F. WHAT IS NOT COVERED UNDER THIS WARRANTY? 1. The SunSetter OASIS Awning is not designed to be used for carports. Any damage that results from the Purchasers use of the SunSetter OASIS Awning for carports is not covered by this warranty. 2. Any failure or damage of the components that results from any intentional or negligent actions by the purchaser or by any other person is not covered by this Warranty. 3.