User Manual
Table Of Contents
- LRP75 Long Range Passive Reader/Writer
- Table of Contents
- Getting Started
- Mechanical Specifications
- Power and Electrical Interface
- Configuration Menu
- Standard RFID Interface
- 5.1 Introduction
- 5.2 Command Timeout Values
- 5.3 Address Blocks
- 5.4 ABx Error Codes
- 5.5 Command Descriptions
- 5.6 ABx Standard Commands
- 5.6.1 Command 4 (04 Hex): Tag Fill
- 5.6.2 Command 5 (05 Hex): Block Read
- 5.6.3 Command 6 (06 Hex): Block Write
- 5.6.4 Command 7 (07H): Read Tag Serial Number
- 5.6.5 Command 8 (08 Hex): Tag Search
- 5.6.6 Command D (0D Hex): Start/Stop Continuous Block Read
- 5.6.7 Command E (0EH) Read SN and Data
- 5.6.8 Command F (0FH) Start/Stop Continuous Read SN and Data
- 5.7 ABx Fast Commands
- 5.7.1 ABx Command Packet Structure
- 5.7.2 Command 4 (04 Hex): Tag Fill
- 5.7.3 Command 5 (05 Hex): Block Read
- 5.7.4 Command 6 (06 Hex): Block Write
- 5.7.5 Command 7 (07H): Read Tag Serial Number
- 5.7.6 Command 8 (08 Hex): Tag Search
- 5.7.7 Command D (0D Hex): Start/Stop Continuous Block Read
- 5.7.8 Command E (0EH) Read SN and Data
- 5.7.9 Command F (0FH) Start/Stop Continuous Read SN and Data
- Technical Specifications
- LRP75 Beta Connections
- Models and Accessories
- ASCII Chart
LRP75 Long Range Passive Reader/Writer 1
1
Getting Started
1.1 Introduction
Escort Memory Systems' passive read/write system is a complete
family of field-proven read/write Radio-Frequency Identification
products.
The system consists of RFID tags, reader/writers, antennas,
controllers, bus interfaces, and ancillary equipment. Tags can be
attached to a product or its carrier and act as an electronic identifier,
job sheet, portable database, or manifest. Tags are read and updated
via an Escort Memory Systems Reader/Writer, through any non-
conducting material, while moving or standing still.
Escort Memory Systems' LRP-Series long range passive RFID
system is the latest in our line of high performance, industrial RFID
equipment. The passive design of the LRP read/write system uses the
RF field from the antenna to power the tag, eliminating the need for
tag batteries. The LRP passive read/write system is designed to
provide cost effective RFID data collection and control solutions to
automation and material handling applications.
The LRP system uses the internationally recognized ISM frequency of
13.56 MHZ to both power the tag, and to establish a radio link to
transfer the information. LRP-Series passive tags provide 48 bytes of
reprogrammable memory.
The LRP75 is encased in a NEMA2 enclosure. The LRP75 is
equipped with an internal antenna that has a range of 4 inches.
The LRP75 has one serial port that supports RS232 or RS422 serial
communications. The serial port is used to receive commands and
software from the host and to send the data back.
1.2 Unpacking and Inspection
When you unpack the LRP75, retain the original shipping carton and
packing material in case any item has to be returned to Escort
Memory Systems. Inspect each item carefully for evidence of
damage. If any item appears to be damaged, notify your Escort
Memory Systems representative immediately.
The following is supplied with the LRP75:
1 LRP75
2 Short screws
2 Long screws
2 Threaded inserts