User's Manual
Table Of Contents
- TABLE OF CONTENTS
- 1 GETTING STARTED 1
- 2 MECHANICAL SPECIFICATIONS 4
- 3 POWER AND ELECTRICAL INTERFACE 14
- 4 SERIAL AND BUS COMMUNICATIONS 29
- 5 MENU CONFIGURATION 35
- 6 RFID INTERFACE 42
- 6.1 In tro duc tion 42
- 6.2 ABx Er ror Codes 45
- 6.3 Anticollision Com mands 48
- 6.4 ABx Stan dard Pro to col 51
- ABxS Com mand 4 (04H): Fill Tag 51
- ABxS Com mand 5 (05H): Block Read 53
- ABxS Com mand 6 (06H): Block Write 55
- ABxS Com mand 7 (07H): Read Tag Se rial Num ber 57
- ABxS Com mand 8 (08H): Tag Search 58
- ABxS Com mand D (0DH): Con tin u ous Block Read 59
- ABxS Com mand 10 (10H): Set Out put 62
- ABxS Com mand 11 (11H): In put Sta tus 64
- ABxS Com mand 84 (84H): Fill Tag All 66
- ABxS Com mand 85 (85H): Block Read All 68
- ABxS Com mand 86 (86H): Block Write All 70
- ABxS Com mand 87 (87H): Read Tag SN All 72
- ABxS Com mand 88 (88H): Tag Search All 74
- ABxS Com mand 89 (89H): EAS Set/Re set All 75
- ABxS Com mand 8A (8AH): EAS Start/Stop 76
- ABxS Com mand 8D (8DH): Con tin u ous Read All 78
- ABxS Com mand 8E (8EH): Mem ory Lock All 80
- ABxS Com mand 94 (94H): SN Fill 82
- ABxS Com mand 95 (95H): SN Block Read 84
- ABxS Com mand 96 (96H): SN Block Write 86
- ABxS Com mand 97 (97H): SN Block Read All 88
- 6.5 ABx Fast Pro to col 90
- ABx Com mand Packet Struc ture: 90
- Com mand/Re sponse Size 91
- Checksum 92
- ABxF Com mand 4 (04H): Fill Tag 93
- ABxF Com mand 5 (05H): Block Read 95
- ABxF Com mand 6 (06H): Block Write 97
- ABxF Com mand 7 (07H): Read Tag Se rial Num ber 99
- ABxF Com mand 8 (08H): Tag Search 101
- ABxF Com mand D (0DH): Con tin u ous Block Read 102
- ABxF Com mand 10 (10H): Set Out put 105
- ABxF Com mand 11 (11H): In put Sta tus 107
- ABxF Com mand 84 (84H): Fill All 109
- ABxF Com mand 85 (85H): Block Read All 111
- ABxF Com mand 86 (86H): Block Write All 113
- ABxF Com mand 87 (87H): Read Tag SN All 115
- ABxF Com mand 88 (88H): Tag Search All 117
- ABxF Com mand 89 (89H): EAS Set/Re set All 119
- ABxF Com mand 8A (8AH): EAS Start/Stop 121
- ABxF Com mand 8D (8DH): Con tin u ous Read All 124
- ABxF Com mand 8E (8EH): Mem ory Lock All 127
- ABxF Com mand 94 (94H): SN Fill 130
- ABxF Com mand 95 (95H): SN Block Read 132
- ABxF Com mand 96 (96H): SN Block Write 134
- ABxF Com mand 97 (97H): SN Block Read All 136
- 6.6 ABx ASCII Pro to col 140
- Com mand Packet Struc ture: 140
- Com mand/Re sponse Size 141
- Checksum 142
- Ex am ple ASCII Com mand 142
- COM1 LED In di ca tor 145
- DeviceNet In ter face 145
- 7.2 In ter face Board Mon i tor Mode 145
- En ter In ter face Board Mon i tor 145
- 7.2.1 Down loading Firm ware to the In ter face Board 147
- Pro duce size Š ABx Stan dard, 8 Byte Read 154
- Pro duce size Š ABx Fast, 8 Byte Read 155
- Con sume size Š ABx Stan dard, 8 Byte Read 155
- Con sume size Š ABx Fast, 8 Byte Read 156
- LRP830 Trans mit Mes sage Size 156
- LRP830 Re ceive Mes sage Size 157
- En ter In ter face Board Mon i tor 145
- 7.2 In ter face Board Mon i tor Mode 145
- Pro to col: Poll or Strobe 157
- DeviceNet Se rial Num ber 157
- ABx sep a ra tion 158
- ABx Non-separation 158
- Polled Com mands in ABx Non-separation Mode 159
- Er ror Man age ment 159
- Trig ger Fea ture 160
- Buf Flush En able 161
- Buf Flush De lay 161
- Header De vice Type Pro to col 163
- Using DNSW32 or DNSW16 171
- Header For mat 179
- Header De vice Type Com mand Pro to col 182
- Cal cu lating Mes sage Size 183
7.2.4 Interface Board Configuration Editor
Note: the following menu can be attained via "Y" (above) or selecting "E"
from the Monitor Menu (above). These are the recommended parameters,
however, it is likely that A and/or B (below) may require modification ac
-
cording to customer requirements.
<= LRP830 INTERFACE-BOARD CONFIGURATION MENU =>
Enter Parameter # to Change:
===== Std DeviceNet =====
90 A. 830 Tx Msg Size (0-254)
90 B. 830 Rx Msg Size (0-254)
0 C. DevNet Protocol (Poll=0,Strobe=1)
D. DeviceNet Serial# 04 99 12 34 (hex)
===== LRP830 Specific =====
2 1. Device Type (GENeric: 0=norm, 1=rev; HDR: 2=n, 3=r)
Y 2. ABx separation (Y/N)
N 3. Buf Flush Enable (Y/N)
200 4. Buf Flush Delay (0-9999)
SELECTION 1-C? (Ctrl-C Exits)
When you wish to exit the interface board configuration menu, enter
"CTRL-C." The following prompt will appear which is responded with "n"
in this example.
Update Flash ROM (y/n)?> n [:-( Flash ROM *Not* Updated )-:]
{-:) Please Reset LRP830 to enter RUN mode (:-}
{HALTED}
<RESET>
The LRP830 must now be reset or power cycled to enable the unit to enter
"RUN" mode.
Copyright © 2000 Escort Memory Systems
150 LRP830-Series Long-Range Passive Reader/Writer