User's Manual
Table Of Contents
- TABLE OF CONTENTS
- 1 GETTING STARTED 1
- 2 MECHANICAL SPECIFICATIONS 4
- 3 POWER AND ELECTRICAL INTERFACE 14
- 4 SERIAL AND BUS COMMUNICATIONS 29
- 5 MENU CONFIGURATION 35
- 6 RFID INTERFACE 42
- 6.1 In tro duc tion 42
- 6.2 ABx Er ror Codes 45
- 6.3 Anticollision Com mands 48
- 6.4 ABx Stan dard Pro to col 51
- ABxS Com mand 4 (04H): Fill Tag 51
- ABxS Com mand 5 (05H): Block Read 53
- ABxS Com mand 6 (06H): Block Write 55
- ABxS Com mand 7 (07H): Read Tag Se rial Num ber 57
- ABxS Com mand 8 (08H): Tag Search 58
- ABxS Com mand D (0DH): Con tin u ous Block Read 59
- ABxS Com mand 10 (10H): Set Out put 62
- ABxS Com mand 11 (11H): In put Sta tus 64
- ABxS Com mand 84 (84H): Fill Tag All 66
- ABxS Com mand 85 (85H): Block Read All 68
- ABxS Com mand 86 (86H): Block Write All 70
- ABxS Com mand 87 (87H): Read Tag SN All 72
- ABxS Com mand 88 (88H): Tag Search All 74
- ABxS Com mand 89 (89H): EAS Set/Re set All 75
- ABxS Com mand 8A (8AH): EAS Start/Stop 76
- ABxS Com mand 8D (8DH): Con tin u ous Read All 78
- ABxS Com mand 8E (8EH): Mem ory Lock All 80
- ABxS Com mand 94 (94H): SN Fill 82
- ABxS Com mand 95 (95H): SN Block Read 84
- ABxS Com mand 96 (96H): SN Block Write 86
- ABxS Com mand 97 (97H): SN Block Read All 88
- 6.5 ABx Fast Pro to col 90
- ABx Com mand Packet Struc ture: 90
- Com mand/Re sponse Size 91
- Checksum 92
- ABxF Com mand 4 (04H): Fill Tag 93
- ABxF Com mand 5 (05H): Block Read 95
- ABxF Com mand 6 (06H): Block Write 97
- ABxF Com mand 7 (07H): Read Tag Se rial Num ber 99
- ABxF Com mand 8 (08H): Tag Search 101
- ABxF Com mand D (0DH): Con tin u ous Block Read 102
- ABxF Com mand 10 (10H): Set Out put 105
- ABxF Com mand 11 (11H): In put Sta tus 107
- ABxF Com mand 84 (84H): Fill All 109
- ABxF Com mand 85 (85H): Block Read All 111
- ABxF Com mand 86 (86H): Block Write All 113
- ABxF Com mand 87 (87H): Read Tag SN All 115
- ABxF Com mand 88 (88H): Tag Search All 117
- ABxF Com mand 89 (89H): EAS Set/Re set All 119
- ABxF Com mand 8A (8AH): EAS Start/Stop 121
- ABxF Com mand 8D (8DH): Con tin u ous Read All 124
- ABxF Com mand 8E (8EH): Mem ory Lock All 127
- ABxF Com mand 94 (94H): SN Fill 130
- ABxF Com mand 95 (95H): SN Block Read 132
- ABxF Com mand 96 (96H): SN Block Write 134
- ABxF Com mand 97 (97H): SN Block Read All 136
- 6.6 ABx ASCII Pro to col 140
- Com mand Packet Struc ture: 140
- Com mand/Re sponse Size 141
- Checksum 142
- Ex am ple ASCII Com mand 142
- COM1 LED In di ca tor 145
- DeviceNet In ter face 145
- 7.2 In ter face Board Mon i tor Mode 145
- En ter In ter face Board Mon i tor 145
- 7.2.1 Down loading Firm ware to the In ter face Board 147
- Pro duce size Š ABx Stan dard, 8 Byte Read 154
- Pro duce size Š ABx Fast, 8 Byte Read 155
- Con sume size Š ABx Stan dard, 8 Byte Read 155
- Con sume size Š ABx Fast, 8 Byte Read 156
- LRP830 Trans mit Mes sage Size 156
- LRP830 Re ceive Mes sage Size 157
- En ter In ter face Board Mon i tor 145
- 7.2 In ter face Board Mon i tor Mode 145
- Pro to col: Poll or Strobe 157
- DeviceNet Se rial Num ber 157
- ABx sep a ra tion 158
- ABx Non-separation 158
- Polled Com mands in ABx Non-separation Mode 159
- Er ror Man age ment 159
- Trig ger Fea ture 160
- Buf Flush En able 161
- Buf Flush De lay 161
- Header De vice Type Pro to col 163
- Using DNSW32 or DNSW16 171
- Header For mat 179
- Header De vice Type Com mand Pro to col 182
- Cal cu lating Mes sage Size 183
At the Interface Setup window (not shown) just use the defaults by pressing
OK.
Next, load the configuration file ( 830net.SCL), using the FILE>OPEN pull
down menu as depicted in Figure 31 and 32. This file can be found on the
LRP830 installation disk.
Copyright © 2000 Escort Memory Systems
172 LRP830-Series Long-Range Passive Reader/Writer
Figure 31 — Opening the LRP830 Configuration File
Figure 32 — File Open Menu