User's Manual
Table Of Contents
- TABLE OF CONTENTS
- 1 GETTING STARTED 1
- 2 MECHANICAL SPECIFICATIONS 4
- 3 POWER AND ELECTRICAL INTERFACE 14
- Power from the MUX32 bus and from an ex ter nal power sup ply 26
- 3.9 LED In di ca tors 27
- 4 SERIAL AND BUS COMMUNICATIONS 29
- 5 MENU CONFIGURATION 34
- 6 RFID INTERFACE 41
- 6.1 In tro duc tion 41
- 6.2 ABx Er ror Codes 44
- 6.3 Anticollision Com mands 47
- 6.4 ABx Stan dard Pro to col 49
- ABxS Com mand 4 (04H): Fill Tag 49
- ABxS Com mand 5 (05H): Block Read 51
- ABxS Com mand 6 (06H): Block Write 53
- ABxS Com mand 7 (07H): Read Tag Se rial Num ber 55
- ABxS Com mand 8 (08H): Tag Search 56
- ABxS Com mand D (0DH): Con tin u ous Block Read 57
- ABxS Com mand 10 (10H): Set Out put 60
- ABxS Com mand 11 (11H): In put Sta tus 62
- ABxS Com mand 84 (84H): Fill Tag All 64
- ABxS Com mand 85 (85H): Block Read All 66
- ABxS Com mand 86 (86H): Block Write All 68
- ABxS Com mand 87 (87H): Read Tag SN All 70
- ABxS Com mand 88 (88H): Tag Search All 72
- ABxS Com mand 89 (89H): EAS Set/Re set All 73
- ABxS Com mand 8A (8AH): EAS Start/Stop 75
- ABxS Com mand 8D (8DH): Con tin u ous Read All 77
- ABxS Com mand 8E (8EH): Mem ory Lock All 79
- ABxS Com mand 94 (94H): SN Fill 81
- ABxS Com mand 95 (95H): SN Block Read 83
- ABxS Com mand 96 (96H): SN Block Write 85
- ABxS Com mand 97 (97H): SN Block Read All 87
- 6.5 ABx Fast Pro to col 89
- ABx Com mand Packet Struc ture: 89
- Com mand/Re sponse Size 90
- Checksum 91
- ABxF Com mand 4 (04H): Fill Tag 92
- ABxF Com mand 5 (05H): Block Read 94
- ABxF Com mand 6 (06H): Block Write 96
- ABxF Com mand 7 (07H): Read Tag Se rial Num ber 98
- ABxF Com mand 8 (08H): Tag Search 100
- ABxF Com mand D (0DH): Con tin u ous Block Read 101
- ABxF Com mand 10 (10H): Set Out put 104
- ABxF Com mand 11 (11H): In put Sta tus 106
- ABxF Com mand 84 (84H): Fill All 108
- ABxF Com mand 85 (85H): Block Read All 110
- ABxF Com mand 86 (86H): Block Write All 112
- ABxF Com mand 87 (87H): Read Tag SN All 114
- ABxF Com mand 88 (88H): Tag Search All 116
- ABxF Com mand 89 (89H): EAS Set/Re set All 118
- ABxF Com mand 8A (8AH): EAS Start/Stop 120
- ABxF Com mand 8D (8DH): Con tin u ous Read All 123
- ABxF Com mand 8E (8EH): Mem ory Lock All 126
- ABxF Com mand 94 (94H): SN Fill 128
- ABxF Com mand 95 (95H): SN Block Read 130
- ABxF Com mand 96 (96H): SN Block Write 132
- ABxF Com mand 97 (97H): SN Block Read All 134
- 6.6 ABx ASCII Pro to col 138
ABxF Command 84 (84H): Fill All
DESCRIPTION
Fill all RFID tags-in-field or all tags in the same family, with a one byte
value over multiple contiguous addresses.
DISCUSSION
This command is commonly used to clear an RFID tag's memory. It writes a
one byte value repetitively across a specified range of tag addresses. All tags
present in the antenna field with the specified Family ID will be affected by
this command.
The Fill All function requires one data value byte, a starting address, and a
fill length. It will fill the tag with the data value byte, starting at the specified
start address for the specified number of consecutive bytes. The Fill Length
must be set to a non-zero value (1-48).
The timeout value is given in 1 msec increments and can have a value of
1EH to FFFEH (65,534 ms). When the Anticollision Index is not zero (mul-
tiple tag-in-field enabled), the LRP820 returns a response after the timeout
expires. If the Anticollision Index is 0, a response is returned when a suc-
cessful operation is performed on 1 tag or when the timeout has expired.
When the timeout is set to 0, the LRP820 will return a syntax error.
Field Content
Header <STX><STX>
Packet Size Packet length in bytes excluding the header, packet size, checksum and ter
-
minator bytes. 0008H for this command
Command 84H
Family ID Tag Family ID - 00H = all tags
Anticollision Index Number of tags expected
Start Address 2-byte value for the starting tag address
Fill Length 2-byte value for the length of the fill in number of bytes (1-48)
Timeout 2-byte value for timeout in 1 ms units. (1EH - FFFEH)
Data value byte 1 byte of fill
Checksum Optional Checksum
Terminator <ETX>
NOTE:
This command can not be used over a MUX32 interface.
Copyright © 2000 Escort Memory Systems
108 LRP820-Series Long-Range Passive Reader/Writer