User's Manual
Table Of Contents
- TABLE OF CONTENTS
- 1 GETTING STARTED 1
- 2 MECHANICAL SPECIFICATIONS 4
- 3 POWER AND ELECTRICAL INTERFACE 14
- Power from the MUX32 bus and from an ex ter nal power sup ply 26
- 3.9 LED In di ca tors 27
- 4 SERIAL AND BUS COMMUNICATIONS 29
- 5 MENU CONFIGURATION 34
- 6 RFID INTERFACE 41
- 6.1 In tro duc tion 41
- 6.2 ABx Er ror Codes 44
- 6.3 Anticollision Com mands 47
- 6.4 ABx Stan dard Pro to col 49
- ABxS Com mand 4 (04H): Fill Tag 49
- ABxS Com mand 5 (05H): Block Read 51
- ABxS Com mand 6 (06H): Block Write 53
- ABxS Com mand 7 (07H): Read Tag Se rial Num ber 55
- ABxS Com mand 8 (08H): Tag Search 56
- ABxS Com mand D (0DH): Con tin u ous Block Read 57
- ABxS Com mand 10 (10H): Set Out put 60
- ABxS Com mand 11 (11H): In put Sta tus 62
- ABxS Com mand 84 (84H): Fill Tag All 64
- ABxS Com mand 85 (85H): Block Read All 66
- ABxS Com mand 86 (86H): Block Write All 68
- ABxS Com mand 87 (87H): Read Tag SN All 70
- ABxS Com mand 88 (88H): Tag Search All 72
- ABxS Com mand 89 (89H): EAS Set/Re set All 73
- ABxS Com mand 8A (8AH): EAS Start/Stop 75
- ABxS Com mand 8D (8DH): Con tin u ous Read All 77
- ABxS Com mand 8E (8EH): Mem ory Lock All 79
- ABxS Com mand 94 (94H): SN Fill 81
- ABxS Com mand 95 (95H): SN Block Read 83
- ABxS Com mand 96 (96H): SN Block Write 85
- ABxS Com mand 97 (97H): SN Block Read All 87
- 6.5 ABx Fast Pro to col 89
- ABx Com mand Packet Struc ture: 89
- Com mand/Re sponse Size 90
- Checksum 91
- ABxF Com mand 4 (04H): Fill Tag 92
- ABxF Com mand 5 (05H): Block Read 94
- ABxF Com mand 6 (06H): Block Write 96
- ABxF Com mand 7 (07H): Read Tag Se rial Num ber 98
- ABxF Com mand 8 (08H): Tag Search 100
- ABxF Com mand D (0DH): Con tin u ous Block Read 101
- ABxF Com mand 10 (10H): Set Out put 104
- ABxF Com mand 11 (11H): In put Sta tus 106
- ABxF Com mand 84 (84H): Fill All 108
- ABxF Com mand 85 (85H): Block Read All 110
- ABxF Com mand 86 (86H): Block Write All 112
- ABxF Com mand 87 (87H): Read Tag SN All 114
- ABxF Com mand 88 (88H): Tag Search All 116
- ABxF Com mand 89 (89H): EAS Set/Re set All 118
- ABxF Com mand 8A (8AH): EAS Start/Stop 120
- ABxF Com mand 8D (8DH): Con tin u ous Read All 123
- ABxF Com mand 8E (8EH): Mem ory Lock All 126
- ABxF Com mand 94 (94H): SN Fill 128
- ABxF Com mand 95 (95H): SN Block Read 130
- ABxF Com mand 96 (96H): SN Block Write 132
- ABxF Com mand 97 (97H): SN Block Read All 134
- 6.6 ABx ASCII Pro to col 138
![](/manual/balluff/lrp800/user-s-manual-english/images/img-44.png)
Start Address (0-47)
Enter the tag address where you want the read to begin.
Length (1-48)
Enter the length of the read you wish the LRP820 to perform. Make certain
that the length value does not exceed the number of possible addresses fol
-
lowing the starting tag address. Entering a read length of 0 will disable Con
-
tinuous Read Mode.
Delay Between Identical Decodes (0-60)
The Delay Between Identical Decodes parameters can have a value of 0 to
60 seconds. When the Delay Between Identical Decodes is set to 0, the
LRP820 will continuously read AND transmit tag data to the host. This can
flood the buffers and cause communication errors and data loss.
Raw Read Response?
If you have selected ABx Fast or ABx ASCII, you have the option of strip-
ping the command protocol from the data and adding a terminator to sepa-
rate the data packets. You can choose a CR (0DH) or CR/LF (0DH, 0AH) to
terminate the data.
Set RF Communication
The LRP820 should be configured with the default (0) Fast Mode.
*** Set RF Communication ***
RF Communication? [0] Fast Mode* [1] Standard Mode 0
Save Changes to EEPROM? [0] No [1] Yes
Restore Factory Defaults
It is often helpful during troubleshooting to restore the LRP820 to known
default values. To do so, select 1from this menu.
*** Restore Factory Defaults ***
Restore Factory Default? [0] No [1] Yes
The restored defaults will be saved to the EEPROM. The communication
defaults can also be restored by placing the main board DIP switch number 5
in the ON position and then restarting the LRP820. After you have saved
any changes, you must re-initialize the LRP820 with switch 5 in the OFF
position.
Copyright © 2000 Escort Memory Systems
38 LRP820-Series Long-Range Passive Reader/Writer